This drain pump for your washer is designed to remove the dirty water during and after the washing cycle. If your washer has water left in it after its washing cycle is over, or if your washer is experiencing leaks around the drain pump, the pump may be damaged or bad and in need of replacement. Ensure you remove and test your drain pump ...Read morewith a multimeter before replacing it. Replacing this pump will require some disassembly of your washer. This pump is sold individually, and does not come with any wire harness or other accessories.
This hose clamp is used in a wide variety of household appliances. Most often it is found in washers, dishwashers, refrigerators, freezers, dehumidifiers, garbage disposals, or air conditioners. This clamp is used to securely attach a hose to another part of your appliance, which helps prevent leaks from those connections. Depending on th...Read moree appliance, it can attach hoses to drain pumps, water inlet valves, pressure switches, and injector nozzles. We recommend you refer to model-specific diagrams for appropriate uses and exact placement. This hose clamp is made of metal, and is sold individually. To access and replace this part you will need a nut driver, pliers, and screwdrivers. Before you begin any repair work, make sure you have unplugged your appliance, and shut off the water supply if applicable.
The front facing foot is sold individually. It is used on your washing machine and can also be known as an adjustable leveling leg. This specific front facing leveling leg has a rubber foot. It is important that when installing this part you are very careful, if not installed correctly your washer will be off balance which will then cause...Read more it to vibrate and/or shake during the cycle. The function of the adjustable foot is to keep your washing machine supported and to make sure that it is level at all times. The tools you will need for this repair include a pair of channel lock pliers, and a 9/16 wrench.
This is a door hinge, which allows for your washer door to properly shut during the washing cycle, and open after it is finished. If your door hinge is bent or broken and not allowing the door to shut properly, this hinge needs to be replaced immediately. Replacing this hinge will require a screwdriver to remove and install. This door hin...Read morege is an OEM part made of durable metal, and does not come with any other parts, like the necessary securing screws or install bracket.
This is a door bellow, also known as a door seal gasket, made for various models of washing machine. This bellow is designed to seal the inner drum of the washer from the outside of the washing machine and its internal components. If your washer is currently experiencing issues with leaking, this gasket is likely worn out and in need of r...Read moreeplacing. This gasket is made of gray rubber and is sold as an individual OEM part and is sold separately from its necessary clamp.
This touch-up paint can be used on a wide variety of household appliances. It is most often used on washers, dryer, refrigerators, dishwashers, ranges, freezers, trash compactors, or microwaves. It is an 18 ml, or.6 fluid ounces, bottle of touch-up paint. It also features a brush for easy application. This quick-drying, long-lasting paint...Read more is perfect for fixing any nicks, scratches, or chips on the exterior of your appliance. This paint is white in color, and provides a durable finish.
This washer dispenser drawer assembly holds detergent, fabric softener, and bleach, dispensing them during the wash cycle to optimize cleaning performance. Compatible with select Whirlpool, KitchenAid, Maytag, Jenn-Air, Amana, Inglis, and Magic Chef models, the assembly includes the drawer, divider, and insert but excludes the front handl...Read moree and housing. Replace your dispenser drawer if it’s leaking, clogged, or not dispensing properly. For safe installation, unplug the washer and refer to the owner’s manual.
The hose clamp is used to hold the water hose in place which will prevent the hose from leaking water. Sometimes the clamp may lose its ability to latch on, causing a leaking washer. For the installation, you will need a flat head screw driver to replace the clamp and a drill to access the screws to remove the front of the washer. Be care...Read moreful if you do not have specific clamp pliers as the clamp could fly off. Once the front of the washer has been removed, take a quick look for water damage or any obvious signs of where the leak is coming from. If it is not obvious, run water to test.
Affresh Washing Machine Cleaner includes three slow-dissolving tablets that help remove odor-causing residue from inside the washer. Suitable for all washer brands, including high-efficiency (HE) machines, the formula is also septic-safe. Place one tablet directly in the empty wash basket and run the Clean Washer cycle, or use a normal cycle with hot water. Use monthly or every 30 wash cycles for best results.
This is a dryer door hinge cap, also known as a bushing, which is a durable plastic cap that is installed on the door hinge and is used to allow your dryer door to operate smoothly when opening and closing. If the door for your dryer is not properly opening and closing, this cap needs to be replaced immediately. To replace this door hinge...Read more bushing, you will need a screwdriver to remove and disassemble the door for your dryer. This door hinge bushing is sold individually, but normally wears at the same rate as the others within your dryer door, so order as many as are needed.
This part is located behind the control panel. It helps determine the level of water in the washer. As the water fills the hose, while tub is filling, it will push the air against a diaphragm inside the switch. More water that enters the tub, more pressure is applied against the switch.
Ask our experts a question about this model and we'll get back to you as soon as possible!
We may have answered a similar question already! Search questions and answers left by others using simple keywords like "fit", "broken", "easy", or "quality" to find questions that match.
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Sort by:
Prev
1
2
3
Next
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Nick - For model number WFW72HEDW0
December 21, 2019
The drain pump stays on and the door is locked and none of the controls work
Hello Nick and thanks for writing.
Your washer may get stuck on this cycle which is called SIPHONING. -Siphoning happens when the end of the washer drain hose is lower than the level of the water inside the washing machine. Siphoning may begin when water is first pumped out of the machine.
We suggest to try a hard reset:
Go to your breaker box and shut the breakers for your unit off, wait 5 minutes and then turn the breaker to on again. That should clear this problem. If it does not clear you would most likely need to replace the drain pump # PS11756700
I recently cleaned out the drain filter. Now, i'm getting water leaking underneath. All of the other hose connections are dry. There are a few drops of water at the base of the drain filter, but the drain filter is tightly screwed in. Would the gasket around the drain filter cap be leaking? Where can i get a replacement?
Hi Scott,
Thank you for your question. If there is water leaking near the cap it is possible the gasket is worn and damaged and the cap may need to be replaced. You will need to remove the cap and inspect it. If it is damaged, the part number for the cap is PS10061775. To place an order for the part you may order it either online, by visiting our live chat sessions, Monday to Friday from 8AM to 4PM EST, or by calling our customer service line at 1-888-738-4871 and anyone will be happy to assist you. We hope this helps. Thank you and have a great day.
2 peoplefound this instruction helpful.
Was this helpful?
Thank you for voting!
Bill - For model number WFW72HEDW0
March 5, 2023
when washer spins thair a knocking sound do you have any idea what is causing this
Hi Bill, thank you for contacting us. According to our research, a knocking sound can be caused by a damaged shock absorber, part number PS11751419. If it does not solve your problem, you need to check your drain pump, part number PS11756700. We hope that helps!
Hello Dennis, thank you for contacting us. Yes the stack kit, part number PS12069913, allows the dryers to be installed on top of the washer. We hope this information is useful!
Hello Bill, thank you for your question. The first part we would recommend checking is the drain pump. The drain pump and filter. If the filter is clogged the water will not all be dispelled. The filter is Part #: PS10061774 and the pump is PartSelect Number: PS11756700. I hope this helps.
See how others fixed this model. Time, tools, difficulty, and steps that lead to victory!View More
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Door locked because of faulty water level switch
28 of 34 peoplefound this instruction helpful.
George from ORO VALLEY, AZ
Really Easy
Less than 15 mins
Nutdriver
First some background. The door locked up the first time when appliance was less than one year old. The "Maytag Repairman" finally succeeded in getting the door open after propping up the front of the machine and fumbling around underneath for a period of time and then assured me the problem was solved. The problem recurred less than a
... Read more year later, and I called another repairman who seemed to have an easier time of it, and charged $293.42 to replace the water level switch. About six months later the same problem recurred and I took the cover off the top of the machine and found there a booklet "For Service Technician's Use Only". VERY HELPFUL. Told how extremely easy it was to unlock door - took about five seconds. Replacing the switch itself involved pulling one tubing off and disconnecting one elec connection from old switch and replacing on new switch. Total cost $50 plus a few dollars for shipping.
Read less
Was this helpful?
Thank you for voting!
Drain pump was cracked
26 of 36 peoplefound this instruction helpful.
JASON from HILLIARD, FL
Very Easy
Less than 15 mins
Nutdriver, Pliers
Turned washer on its side. Pulled the bottom plate off. Then unplugged the electrical lines. Then unbolted the drain pump and bolted the new drain pump in. Then reversed the process.
Was this helpful?
Thank you for voting!
One of the hinges broke, making the door sag
21 of 30 peoplefound this instruction helpful.
Sandy from MILWAUKIE, OR
Easy
1- 2 hours
Using the Torx Screwdriver, we removed the door from the unit. Then we removed all of the screws on the inside of the washer door. After that we flipped it over and opened it up exposing the inside. We couldn't separate them entirely because there was a screw under the latch piece that we couldn't figure out how to get to. However with a
... Read morell the screws out on the inside of the door, we did have enough room to open it up and access the place cover that holds the hinges in. Once we accessed that we removed the roller tips from the old unit and placed them on the new one. Then we reversed the process. With a couple screws in we realized we had put the hinge in reversed from what it needed to be, so we reopened it and switched it around. Then completed replacing all the screws and reattached it to the washer. It opens and closes perfectly and we saved a couple hundred dollars for sure, as the quote to come out had been a $150 trip charge.
My Orders
