This oven temperature sensor, for ranges, works together with the oven control board to measure and regulate the oven temperature. The sensor detects the temperature in the oven cavity. If the following symptoms occur, replacing the temperature sensor could be the solution: Little or no heat when baking, oven not heating evenly, oven will...Read more not start, and/or oven is overheating. Often, if the sensor is defective, the oven temperature will fluctuate and be inaccurate by more than 50 degrees. The tool needed for this replacement is a #2 square head screwdriver or a #2 Philips screwdriver. Remember to unplug the range before installing the part.
This is a multi-use and multi-appliance screw. It can be used on a microwave, refrigerator, range/oven, air conditioner, dehumidifier, washer, or dryer. The measurements of this screw are 8 x 1/2 inch. It has 6 threads. Refer to the manual provided by the manufacturer for further information on repair and accurate guidance. Remember to wear work gloves as a safety precaution.
This is an oven igniter for various ranges. This part is designed to ignite the gas from your oven and provide the heat output inside it. If your oven is having issues turning on or heating up properly, this igniter is likely bad or shorted, and in need of replacement. Replacing this igniter will only require a screwdriver and will simply...Read more need to be disconnected via its wire harness connection, and then reconnected with the new one. This igniter is an OEM part and is sold on its own, without any other parts.
This oven rack is an OEM part designed specifically for ovens. It provides an accessible storage system for oven racks and baking sheets when not in use. This rack measures 15.5 x 25in.
This oven door gasket is designed to form a secure seal around the perimeter of the oven door, helping to maintain consistent internal temperatures during cooking. Made from heat-resistant materials, it prevents heat from escaping the oven cavity, improving energy efficiency and reducing cooking times. Over time, gaskets can wear out or b...Read moreecome damaged, leading to performance issues. Replacing a worn gasket is a simple way to restore your oven’s efficiency. This part is sourced directly from the manufacturer and is sold individually.
Appliance spray paint is a great way to cover up any chips and scratches that have appeared on your appliances. Instead of replacing the part entirely, this is an easy fix. This is also a great way to give a fresh new look to any handles or areas that have discoloring due to wear. Make sure to clean the area before you begin and wear a pr...Read moreotective mask for safety. Give the can a good shake and spray a few inches away from the surface. Apply the paint until the area is fully covered as desired. Wait until the paint has dried before using the appliance.
Ask our experts a question about this model and we'll get back to you as soon as possible!
We may have answered a similar question already! Search questions and answers left by others using simple keywords like "fit", "broken", "easy", or "quality" to find questions that match.
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Sort by:
Prev
1
2
3
Next
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Dennis Warrick - For model number WFG320M0BW2
February 15, 2020
Where is the oven sensor located?
Hello Dennis,
Thank you for your question. The part you are referring to would be under part number PS11749737. The sensor is located on the inside of the oven, in the back. We hope this helps you.
Hi Barbara, thank you for getting in touch. The exterior door glass for your model is part number PS11756071, and the inner door glass is part number PS11756069. We hope that helps!
Oven won't ignite every time I see glow coming from igniter but takes long time for flame
Hi Edward, thank you for reaching out. According to our research on the model, the Oven Igniter appears to be weak and you may need to replace it with part number PS12348439. If you need help placing an order, customer service is available 7 days a week. Glad to be of help!
Switching from propane to natural gas, need the orifices to complete conversion. Phone representative said can order through you. Did not see them.
Hello Barbara, thank you for your question. You will need one of each part number PS11753337, PS11749489, and PS11749491 to convert to natural gas. If you require assistance to place an order, please contact customer service. We hope that helps!
Oven worked perfect yesterday. Today ignites for stove top do not work. What is the cause? Made slight click then quit
Hi Rhonda, thank you for your question. If the surface burners are not igniting, there are a couple of things that you will need to check. First check and see if the burner caps aligned correctly. If they are not aligned correctly, you will need to re-position them. If you have recently cleaned the cooktop or if there has been excess moisture caused from either cooking or spills, remove the burner caps and allow the burners to dry out before using them again. If there is food debris in the burners, they will need to be cleaned, so they can work properly. If you have done all this and the burners will not light, you may need to replace either the spark module, the spark ignition switch or the igniter. We hope this helps!
See how others fixed this model. Time, tools, difficulty, and steps that lead to victory!View More
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
mice had made nests in the insulation wrap in the range
127 of 208 peoplefound this instruction helpful.
Wendy from Red Hook, NY
Easy
More than 2 hours
Screw drivers
I numbered every part. ex: 1 L., for first part removed left side. I used a magic marker to circle the holes and wrote the number of screws used on the part, set the srews in a separete place, so that I new where these screws went to. The cleanup was pretty time consuming, but I was able to keep my stove, when every repairman I called to
... Read more fix my stove told me I was better off buying a new stove. ($600.00 stove 2 years old)Please Note: The insulation blanket needed for the entire stove is two pieces, the sides and top are one part # and the bottom and back, are another part #. I did not know this. I just purchased the top and sides. I got lucky, the back and bottom were still in good shape. So I guess I should have read the description of the part more carefully to see what it covers, before I ordered it. It took two people two hours to do the work, it was really nice to have an extra set of eyes, to remember what direction pieces of metal from the stove went. I would do it all over in a heart beat instead of buying a new stove.
Read less
Was this helpful?
Thank you for voting!
temperature not accurate after 3 1/2 years of happy usage
144 of 272 peoplefound this instruction helpful.
Ruth from Oregon, IL
Really Easy
15 - 30 mins
Screw drivers
Opened up the back of the stove. Unpluged the sensor. Replaced the sensor. Replace the back of the stove.
The sensor that has been replaced is not what is expected. After reading all of the instructions for adjusting the temperatures, the only temp that stays steady is when we first turn on the oven to 350 degrees. That stays s
... Read moreteady but when I turn it to 400 it slowly goes up to 425 degrees.
Read less
Was this helpful?
Thank you for voting!
Oven stuck in cleaning mode
48 of 88 peoplefound this instruction helpful.
Hal from Santa Rosa, CA
Really Easy
Less than 15 mins
Screw drivers
Google the error code that the range was displaying and found others with the same symptoms. Then found several people that had fixed the problem by replacing the oven sensor. I then ordered the sensor and replaced it, which fixed the problem.
My Orders
