WF448AAPYE Samsung Washer - Parts

This washer door lock and switch assembly is a critical safety and control component for front-loading washing machines. It secures the door during wash and spin cycles, preventing accidental opening and ensuring the appliance operates only when properly latched. The integrated interlock switch communicates with the washer’s control syste...Read morem to verify door status, helping prevent cycle interruptions and operational errors. This model features a four-lead switch for precise functionality and is compatible with a wide range of front-load washers. Replacing this part can resolve issues such as a door that won’t close, won’t open, or won’t lock, as well as a washer that fails to start. Installation should be performed with the appliance unplugged and may require basic tools.

This part is used for the shaft on the rear of the tub and is sold individually. The head bolt is part of the spider arm assembly, and they are generally changed at the same time. If you are replacing the entire spider arm assembly, make sure you order as many hex bolts as you will need. The spider arm assembly contains 6 of these hex bol...Read morets. The hex bolt or spider arm assembly may need to be replaced if you notice that your inner tub is going out of balance. The hex bolt measures 1.5 by 0.5 inches.

This is an individually sold front shock absorber designed for use with Samsung dryers. Shock absorbers are used to distribute the weight of the dryer drum evenly and ensure that the different bumps and bounces that occur during the drying cycle are smoothed and counter acted. A broken shock absorber is noticeable by the amount of noise y...Read moreour dryer will make during operation. Replacing this absorber and its rear counterpart may even be necessary to the lifespan of the other dryer parts, so be sure to inspect both absorbers before ordering. To install this OEM shock absorber in your dryer, you will need to disassemble the dryer, which requires a screwdriver and wrench.

This is an outer seal clamp for the washer door boot of your Samsung washing machine. This clamp tightly seals the boot of the drum within the door of the washer to prevent leaks. This clamp is made of metal and features a spring in the middle, but over time can be worn down or break, and result in water leaking out of the washing machine...Read more and into your home. Replacing this clamp will require a screwdriver, pliers, and safety gloves. This clamp is an OEM part that comes individually, without any other parts or accessories.

This is a door switch assembly designed for Samsung washing machines. This door switch assembly is used to latch and lock the door shut before the washing cycle commences and communicates with the control board when that is done. If your washer door is not locking or latching properly, the door switch is likely bad or broken and will need...Read more to be replaced. To replace this assembly, you will need a flat-head and Philips-head screwdriver. This part is a genuine OEM switch assembly and is sold individually, without any wire harnesses or securing screws.

Shipping bolts are installed through the back of the washing machine, and hold the wash tub and basket in place while your washer is being transported. The tub suspension holds the tub correctly in place during the wash, rinse, and spin cycles. If this suspension is damaged during shipping, the tub can shake and move, tilt to one side, or...Read more spin incorrectly. This could lead to the suspension or motor failing. When moving your washer, it is suggested that you insert the shipping bolts back into place before moving the machine. This part is also called a washer transit bolt. Remember that this part is sold separately, and to check your model to see how many you require.

Assembly BOLT;SWF-P12,MOTOR/

The thermistor monitors and helps regulator the water temperature in the washer.

The pressure switch senses and controls the water level in the washer.

This is a seal for various models of Samsung washing machines. This part acts as a seal for the rear and front outer part of your washing machine tub and is used to prevent any matter of leaks. If your washing machine is leaking or you notice water outside of the tub after a cycle is finished, this seal could be worn out or damaged and ne...Read moreed immediate replacement. This seal will be located between the two halves of the inner tub and replacing it will require you to disassemble your washing machine, and only requires a few parts like a screwdriver, wrench, and pliers. This OEM seal does not come with any other parts and is sold individually.

This drain pump filter helps trap lint, debris, and small objects before they enter the pump system. By reducing blockages and improving water flow, it supports efficient drainage and helps protect internal components from damage.