This part is used for the shaft on the rear of the tub and is sold individually. The head bolt is part of the spider arm assembly, and they are generally changed at the same time. If you are replacing the entire spider arm assembly, make sure you order as many hex bolts as you will need. The spider arm assembly contains 6 of these hex bol...Read morets. The hex bolt or spider arm assembly may need to be replaced if you notice that your inner tub is going out of balance. The hex bolt measures 1.5 by 0.5 inches.
This is an outer seal clamp for the washer door boot of your Samsung washing machine. This clamp tightly seals the boot of the drum within the door of the washer to prevent leaks. This clamp is made of metal and features a spring in the middle, but over time can be worn down or break, and result in water leaking out of the washing machine...Read more and into your home. Replacing this clamp will require a screwdriver, pliers, and safety gloves. This clamp is an OEM part that comes individually, without any other parts or accessories.
This is a door diaphragm, also commonly known as a door boot seal, for a washer. The boot is fitted between the washer door and the tub to prevent leaking while the appliance is in use. It is made of rubber and is gray in color. Your boot can tear if the washer is overloaded. Alternatively, age and detergents can wear and dry out the boot...Read more which causes it to become brittle and weak. This may cause your washer to leak, and you may need to replace the boot. This is an authentic replacement part from the original manufacturer.
This is the drain pump assembly for various models of Samsung washing machines. The drain pump is used to remove any water from the washer after it has completed its washing cycle. If your washer still has water left in the tub after it has finished washing this drain pump assembly is likely bad defective or worn out and in need of replac...Read moreing immediately. It is important that you do not use your washer with a bad drain pump as that could lead to further damage to your washer clothes or home. This drain pump assembly is approximately 4.5 inches tall and will require tools such as a wrench and screwdriver to access and replace. This drain pump is sold as an individual OEM part and does not include any securing screws.
Shipping bolts are installed through the back of the washing machine, and hold the wash tub and basket in place while your washer is being transported. The tub suspension holds the tub correctly in place during the wash, rinse, and spin cycles. If this suspension is damaged during shipping, the tub can shake and move, tilt to one side, or...Read more spin incorrectly. This could lead to the suspension or motor failing. When moving your washer, it is suggested that you insert the shipping bolts back into place before moving the machine. This part is also called a washer transit bolt. Remember that this part is sold separately, and to check your model to see how many you require.
This manufacturer-approved screw is for refrigerators, including Kenmore refrigerator model. Avoid cross-threading refrigerator screw during installation.
Ask our experts a question about this model and we'll get back to you as soon as possible!
We may have answered a similar question already! Search questions and answers left by others using simple keywords like "fit", "broken", "easy", or "quality" to find questions that match.
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Sort by:
Prev
1
Next
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Adela - For model number WF231ANWXAA
October 28, 2022
Hi my washer fill with water but don't spin an is a code in the 3E we change the water pump still don't work
Hello Adela, thank you for reaching out. According to our research, code 3E appears when the motor is not running properly. First, restart the cycle by pressing the start/pause button. If the code reappears, we would recommend checking the following parts to fix your issue: RPS Sensor, part number PS4204673, Motor Stator, part number PS4204678, and Motor Rotor, part number PS4204680. If you require assistance to place an order, please contact customer service. We hope that helps!
See how others fixed this model. Time, tools, difficulty, and steps that lead to victory!View More
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
OE error code, water keeps flowing during spin cycle, softener dispenser left half full of water, clothes wet after washer stops
3 of 3 peoplefound this instruction helpful.
Gary from Peachtree City, GA
Really Easy
15 - 30 mins
Screw drivers
Found a repair video of a Samsung washer that looks like mine (9 years old). Removed two screws from the back of the washer, slid the top a few inches toward the front and lifted it off. Disconnected the two double electrical connections, the two rubber tubes from the solenoids, the cold water hose from the back and removed the two scre
... Read morews holding the valve in place. Installed the new valve by reversing those steps, slid the top back into place and secured it with the two screws and viola (as Kelly Bundy would say)! The washer now functions normally. I'm waiting for my next water bill to arrive to see whether the sudden increase in usage decreases to its normal amount. We have three adults and four small children in the household so the washer is constantly in use.
Read less
Was this helpful?
Thank you for voting!
Leaking water inlet hoses.
4 of 6 peoplefound this instruction helpful.
Helen from NASHUA, NH
Really Easy
30 - 60 mins
Removed the old hoses and screwed on the new hoses.
Was this helpful?
Thank you for voting!
Old hot water inlet hose had budge at both ends.
2 of 5 peoplefound this instruction helpful.
Jimmy from MEMPHIS, TN
Very Easy
Less than 15 mins
Pliers
Turn water off at the inlet valve of hose you are replacing. Disconnect inlet hose the washer and let water drain out in a bucket. Then remove old hose. Replace new hose to inlet valve then washer . Use pliers to tighten both ends. Turn on water to check leaks at both ends of hose.
My Orders
