- Home
- WED8300SW0
- Instructions
WED8300SW0 Whirlpool Dryer - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
A hole in filter
3 of 3 people
found this instruction helpful.
-
Russ from Vernal, UT
- Really Easy
- Less than 15 mins
Remove old filter
Vacuum out
Install new filter
Vacuum out
Install new filter
Was this helpful?
Thank you for voting!
Dryer would not start!
5 of 9 people
found this instruction helpful.
-
Manny from ODESSA, TX
- Really Easy
- Less than 15 mins
-
Socket set
Unplug unit first.
Took the front cover off the front of dryer below the door.
Took the front cover off the front of dryer below the door.
Was this helpful?
Thank you for voting!
not drying completely on the automatic settings
3 of 3 people
found this instruction helpful.
-
Jason from Colorado Springs, CO
- Easy
- Less than 15 mins
-
Pliers
Not a handyman but this was an easy and cheap fix. Now the automatic settings are working and drying much faster. Unplug machine, front panel has 2 spring clips toward the edges that you stick a flat tool into and pull on the panel to open. Pull off the electrical connections from the old sensors by the right side of the lint screen.
... Read more
Needlenose pliers help with the one farther up there. Then just pull the old ones sensors out, stick the new ones in, reconnect the electrical and get ready to live the good life with dry clothes that don't smell musty.
Read less
Was this helpful?
Thank you for voting!
Dryer squealing loudly during operation
3 of 3 people
found this instruction helpful.
-
Joseph from WEST PALM BCH, FL
- A Bit Difficult
- 30 - 60 mins
-
Screw drivers, Socket set
Unplug dryer from 220VAC outlet
Remove bottom cover panel, slip a flat blade screwdriver into each clamp, and bottom piece becomes removable. Pull forward and lift bottom cover piece.
Pull up top section from dryer frame. Disconnect dryer door off/on contact three wire switch by pressing plastic connector together ... Read more . You may need a small flat blade screwdriver to seperate connector.
Remove two Torx (T15 head) screws in the far left and right corners of the front door panel.
Remove two screws underneath dryer lint screen, be careful to not let front door and front cover fall forward. The rotating dryer drum will now be loose.
Underneath drum, there is a cover panel over the dryer motor. Likely you will find a bunch of lint all about. This dryer had likely not been cleaned in many years.
Remove screws on dryer motor cover.
Remove panel. Likely, you’ll more lint about.
After vacuuming, use a flashlight and hand mirror to locate belt tensioner, back side of motor. If your belt is not broken, press down on the tensioner spring and remove belt from tensioner and motor. Inspect belt, replace if worn. In this instance the belt was well worn.
Slowly pull dryer drum forward, walking belt along as you bring drum forward out of the dryer casing.
At this point you have plenty of room to access the one bolt holding the tensioner, in this instance it was a 13mm socket. Be careful to remove the tensioner springs before removing the bracket. Your PartsSelect is an identical match to the original one.
Install new tensioner, tighten slightly, then put springs back on.
Reverse this entire process to get your dryer back together and back running smooth and quiet as it was when new.
This dryer was quieter than its owners remembered it being back when new 15 years ago.
Well worth saving the $ doing your own work.
Good luck on your repair endeavor!
Remove bottom cover panel, slip a flat blade screwdriver into each clamp, and bottom piece becomes removable. Pull forward and lift bottom cover piece.
Pull up top section from dryer frame. Disconnect dryer door off/on contact three wire switch by pressing plastic connector together ... Read more . You may need a small flat blade screwdriver to seperate connector.
Remove two Torx (T15 head) screws in the far left and right corners of the front door panel.
Remove two screws underneath dryer lint screen, be careful to not let front door and front cover fall forward. The rotating dryer drum will now be loose.
Underneath drum, there is a cover panel over the dryer motor. Likely you will find a bunch of lint all about. This dryer had likely not been cleaned in many years.
Remove screws on dryer motor cover.
Remove panel. Likely, you’ll more lint about.
After vacuuming, use a flashlight and hand mirror to locate belt tensioner, back side of motor. If your belt is not broken, press down on the tensioner spring and remove belt from tensioner and motor. Inspect belt, replace if worn. In this instance the belt was well worn.
Slowly pull dryer drum forward, walking belt along as you bring drum forward out of the dryer casing.
At this point you have plenty of room to access the one bolt holding the tensioner, in this instance it was a 13mm socket. Be careful to remove the tensioner springs before removing the bracket. Your PartsSelect is an identical match to the original one.
Install new tensioner, tighten slightly, then put springs back on.
Reverse this entire process to get your dryer back together and back running smooth and quiet as it was when new.
This dryer was quieter than its owners remembered it being back when new 15 years ago.
Well worth saving the $ doing your own work.
Good luck on your repair endeavor!
Read less
Was this helpful?
Thank you for voting!
Bad screaming noise
3 of 3 people
found this instruction helpful.
-
David from HUNTINGDON VY, PA
- Really Easy
- 30 - 60 mins
-
Screw drivers, Socket set
Replaced 4 wheels and new belt
Was this helpful?
Thank you for voting!
Squealing when running
3 of 3 people
found this instruction helpful.
-
MICHAEL from Baden, PA
- A Bit Difficult
- 30 - 60 mins
-
Nutdriver, Pliers, Screw drivers, Socket set
You tube and supplied video directions for the make and model. Follow step by step and the repair went easy. Worried when removing the dryer drum but it went smooth.
Was this helpful?
Thank you for voting!
Belt was raffling and there was aloud knocking sound
3 of 3 people
found this instruction helpful.
-
Genette from CLEVELAND, MS
- Really Easy
- 15 - 30 mins
-
Socket set
Removed the screws replaced the belt and lubricated the wheels and that fixed my Knocking and it runs like when I first got it
Was this helpful?
Thank you for voting!
Replace heating element and belt
3 of 3 people
found this instruction helpful.
-
James from LAFAYETTE, TN
- Easy
- 30 - 60 mins
-
Nutdriver, Socket set
Replaced heating element and went ahead and replaced the belt since the dryer was coming apart and belt taken off also. I used the parts select video and paused the video through each step to complete each step. There videos are great for this and as long as you pause and do each step per the video it is quite easy. I Highly recommend doi
... Read more
ng each step one at a time as I did not have a problem. Thanks for great repair videos.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
cold air vent in dryer was broken
3 of 3 people
found this instruction helpful.
-
MIKE from WESTLAND, MI
- Really Easy
- 30 - 60 mins
-
Screw drivers
remove 3 screws vent comes out put new part in works grate just like new a gain
Other Parts Used:
Was this helpful?
Thank you for voting!
dryer making noise. order parts
4 of 6 people
found this instruction helpful.
-
Thomas from TULELAKE, CA
- Very Difficult
- 30 - 60 mins
YOU NEVER SENT ME THE PARTS!!!
I had to drive to a parts store to find them. On January 17, 2024, I tried to call you when the parts did not arrive and your recording said there were no reps available and you hung up. WE CANNOT GET HELP TO CANCEL THIS ORDER. We have been going in circles with PartSelect and shipping. SO, how do I ... Read more get my refund of the $107.26 for the parts that I never received!!
I had to drive to a parts store to find them. On January 17, 2024, I tried to call you when the parts did not arrive and your recording said there were no reps available and you hung up. WE CANNOT GET HELP TO CANCEL THIS ORDER. We have been going in circles with PartSelect and shipping. SO, how do I ... Read more get my refund of the $107.26 for the parts that I never received!!
Read less
Was this helpful?
Thank you for voting!
Dryer was very loud and sounded like it was scraping
3 of 3 people
found this instruction helpful.
-
Annde from JEFFERSON CTY, TN
- Really Easy
- 15 - 30 mins
-
Pliers, Screw drivers, Wrench (Adjustable)
Took the back and top off of my front loader. I had checked on you tube for the problem and how to fix it and ordered the part. Just followed the directions on how to remove the old idle pulley and installing the new one. Dryer runs like new!
Was this helpful?
Thank you for voting!
Squeaky dryer
3 of 3 people
found this instruction helpful.
-
robert from ELMA, WA
- Really Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
Ezee pezee lemon squeezee.
Was this helpful?
Thank you for voting!
Dryer would shut off mid way through cycle and give an E1 error code
5 of 9 people
found this instruction helpful.
-
Dwayne from Bainbridge, PA
- Easy
- 15 - 30 mins
-
Pliers, Socket set
After turning off the power to the dryer I removed two screws to the bottom front panel and droped it out of the way. I remved three screws hloding the lint screen in place just for better axcess to the element. I then removed the two wires attached to the element and then the two screws holding the element in place. I put everything back
... Read more
together in reverse. I also took the time to clean any dust and lint out.
Read less
Was this helpful?
Thank you for voting!
Dryer would not start.
3 of 3 people
found this instruction helpful.
-
MONA from SHAMROCK, TX
- Really Easy
- 15 - 30 mins
-
Screw drivers, Socket set
I watched the video or I would have likley just called a repair man. It took longer to clean behind the dryer than to install the new thermal fuse. After taking the back off the dryer is was as simple as changing a fuse. Dryer works like new for about $20 bucks and we avoided the hasle of getting a repair man, especially since we live in
... Read more
the country. Thanks for having a web site that is so easy to use and full of good information.
Read less
Was this helpful?
Thank you for voting!
i exchange thermal fuse
5 of 9 people
found this instruction helpful.
-
Greg from HANOVER PARK, IL
- Really Easy
- 30 - 60 mins
very easy
Was this helpful?
Thank you for voting!