EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

WED8300SW0 Whirlpool Dryer - Instructions

All Instructions for the WED8300SW0
61 - 75 of 877

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Door latch (female part) was broken.
11 of 11 people found this instruction helpful.
  • JEANMARIE from BELLEROSE, NY
  • Really Easy
  • Less than 15 mins
  • Screw drivers
I used a screwdriver to remove the old part and pushed the new part in with my fingers, it was very easy. If I could do it, anyone can. I was a lot cheaper then having a repair man come to house. I am very glad I found your site online, I will definitely be using your company again.
Was this helpful?
Thank you for voting!
Rear dryer drum seal came out
17 of 29 people found this instruction helpful.
  • William from Pontiac, MO
  • Easy
  • More than 2 hours
  • Screw drivers, Socket set
Used my Whirlpool Dryer User Instructions Manual and followed instructions and used the Cabinet Parts page to see the diagrams.
Was this helpful?
Thank you for voting!
User Interface was not working correctly. Although indicator was pointing to a specific setting, this setting was not lighted and did not work. The dryer would in fact still operate but not to the selected cycle.
12 of 15 people found this instruction helpful.
  • Louie from Brewer, ME
  • Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers
I assumed that since the display was not working properly that the cause must be the user interface. To remove the interface you must first unplug the power to the unit. In the back of the top of the dryer are 2 5/16" screws that need to be removed (Nutdriver). Once removed, the top panel of the dryer can be slid back exposing the drum and the back of the user interface. The interface can then be pried outwards to unsnap it from the housing. Once you've freed this panel, follow the wires back to where they plug into the electrical connection near the drum and unplug the interface from this connection. With this complete, flip the panel over so that you're looking at the back of it and carefully pry the tabs out (screwdriver)so that the inner interface can be removed. The selector knob will come off and will need to be put back on once you've added the new part. Now add the new interface, ensuring that all tabs click back into place, add the selector knob and route wires back to the electrical connection and plug in. Snap the front interface panel back into place and re-install top dryer panel over drum and replace the 2 5/16" screws. Return power to the dryer and you've finished.
Was this helpful?
Thank you for voting!
Scratches in Surface
83 of 228 people found this instruction helpful.
  • Michelle from Richardson, TX
  • Really Easy
  • Less than 15 mins
This product comes in a bottle with a brush like Liquid Paper. It goes on incredibly easy. A second coat might be needed. I wanted to prevent rust from setting in so I covered the scratches and dings. The paint is a little brighter since my washer is 10 years old but it still looks great.
Was this helpful?
Thank you for voting!
squeaking sound due to worn out bearing idler pulley wheel.
13 of 18 people found this instruction helpful.
  • Evan from NORTHRIDGE, CA
  • Really Easy
  • 30 - 60 mins
  • Nutdriver, Screw drivers
BEFORE ANYTHING ELSE UNPLUG THE POWER AND TURN OFF THE GAS SUPPLY 1. unscrew the 3 nut screws at the back to remove the cover lid. 2. pull the control console cable from the electronic board. (only 3 wires on it).3. unscrew the 2 nut scr ews of the control console then remove it by pulling up.4. unscrew the 5 screws to remove the door. (pull little up to unhinged then remove). 6. unscrew the 5 nut screws to remove the lower siding. 7. unscrew the copper 4 nut screws then remove the lint suction fixture 8. unscrew the 4 nut screws to remove door fixture ,then just lay next to the machine.(the wires are long enough so you don't need to unplug and separate it from the machine.9. remove the belt by pulling the idler pulley towards the motor pulley (against the tension spring) 10. remove the drum by lifting a little bit upward. 11. remove the plastic triangular lock using a small screw driver then remove the idler pulley wheel then install the replacement. (clean your machine using a vacuum cleaner and remove all the lints). 12. install back the drum, be sure to set the drum belt to the right position. (groove on drum side). 13. install back the belt to the pulley the same procedure as to remove it. 14. assemble back what you have removed. end.
Was this helpful?
Thank you for voting!
When using the dryer the cycle would stop and display E1 as the reason
13 of 18 people found this instruction helpful.
  • Joyce from Holbrook, NY
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
Unscrewed the bottom panelof the dryer and located the thermistor through the schematic for my machine. Removed the old one and put the new one in the same way. No more E1 problems and all cycles now complete themselves.
Was this helpful?
Thank you for voting!
Dryer not heating
16 of 27 people found this instruction helpful.
  • Stephen from Andalusia, AL
  • Easy
  • 30 - 60 mins
  • Nutdriver, Wrench (Adjustable)
Open breaker and ensure power was off. Checked heating components for continuity.Found thermal fuse had an open circuit.Replaced High limit thermostat and thermal fuse.Now is a good time time check for free flowing vent piping.I discovered mine was crimped below the floor and caused lint build up and obstructing the flow which could have led to the thermal fuse blowing.I replaced the vent piping as well.My wife says the dryer works better now than it ever has.
Was this helpful?
Thank you for voting!
Idler pulley wore out
10 of 11 people found this instruction helpful.
  • Peter from HUEYTOWN, AL
  • Very Easy
  • 15 - 30 mins
  • Screw drivers, Socket set
Removed the back panel and saw that the idler pulley was worn out. It only took me 5min. To replace, it was very easy to replace.
Was this helpful?
Thank you for voting!
Heater Element bad.
10 of 11 people found this instruction helpful.
  • Christian from JOHNSTON, IA
  • A Bit Difficult
  • 1- 2 hours
  • Nutdriver, Pliers, Screw drivers
Followed video step by step. Perfect instructions. I’d only add that you should get and wear mechanics gloves. My hands got torn up by the sharp metal edges taking apart and putting it back together. Ouch!!
So happy with Partselect though. Super fast shipping and a perfect instructional video. Thanks!!

P.S. Wear gloves! !!
Was this helpful?
Thank you for voting!
Broken belt. Broken idle pully and replace 4 rollers
11 of 14 people found this instruction helpful.
  • Mike from INOLA, OK
  • Easy
  • More than 2 hours
  • Nutdriver, Screw drivers, Socket set
By watching the video it made the job much easier than I thought it would be. I was very pleased with the speedy delivery of the Dryer kit I had ordered. I had called a local repair facility and they wanted twice as much for the same parts.
Was this helpful?
Thank you for voting!
Dryer squeeching very loud
9 of 9 people found this instruction helpful.
  • Michael from ENOLA, PA
  • Very Easy
  • 15 - 30 mins
  • Nutdriver, Socket set
Took off back of dryer Undid belt from belt adjuster pulled and took off adjuster put new one on redid belt and put back on dryer. Done
Was this helpful?
Thank you for voting!
gasket came off lent filter
11 of 15 people found this instruction helpful.
  • stephen from langley, KY
  • Really Easy
  • Less than 15 mins
i could not find this part anywhere locally,so i found this web site which had this part.i ordered this part and am very glad i did.i received it in 2 days.thank you very much.if you need anything check this place first,you will be very satisfied.
Was this helpful?
Thank you for voting!
my teenage son was messing around and got into the dryer and broke the door catch and bent the door.
13 of 21 people found this instruction helpful.
  • Dawn from Chesapeake City, MD
  • Really Easy
  • Less than 15 mins
removed the catch and the pin and replaced it. We were sent a couple different sizes so we tested the one that looked like the closest match. I think the pin was made with different thicknesses of metal. Worked great and saved us from having to get a new dryer!
Was this helpful?
Thank you for voting!
The old door catch failed. Clothes won't dry with door open !
8 of 8 people found this instruction helpful.
  • Theresa from Norfolk, VA
  • Really Easy
  • Less than 15 mins
  • Pliers, Screw drivers
Old door catch came out, new one slipped in. All works great.
Was this helpful?
Thank you for voting!
Dryer was working but not generating heat.
8 of 9 people found this instruction helpful.
  • Laurie from Natick, MA
  • Easy
  • 15 - 30 mins
  • Screw drivers
I was reluctant to call a repair service. Typically when an appliance is as old as my dryer (14 years old), service people encourage you to replace, not repair. I had replaced the dryer's motor within the last 5 years and believed my dryer still had life to it. At first, I tried cleaning the lint build up from the dryer cavity and hose s. This worked but only for a couple of days. After reading other successful repair stories on the website, I decided to try replacing the thermal fuse. It was so easy. The part was easily identifiable. It was just a little hard to yank off the connecting wires. Good as new and no service call.
Was this helpful?
Thank you for voting!
All Instructions for the WED8300SW0
61 - 75 of 877