Switch to Classic
Models > WDT750SAHZ0

WDT750SAHZ0 Whirlpool Dishwasher - Overview

Sections of the WDT750SAHZ0

[Viewing 11 of 11]
Keep searches simple, eg. "belt" or "pump".
Dishwasher Lower Dishrack Wheel Assembly - Gray – Part Number: W10195416V
Dishwasher Lower Dishrack Wheel Assembly - Gray
★★★★★
★★★★★
(284)
PartSelect #: PS11722152
Manufacturer #: W10195416V
This OEM gray Dishwasher Lower Dishrack Wheel Assembly is a plastic kit that allows the rack to slide in and out of the dishwasher easily. If it breaks or becomes damaged. sliding will feel difficult....
$38.01
  In Stock
Door Balance Link Kit – Part Number: 8194001
Door Balance Link Kit
★★★★★
★★★★★
(187)
PartSelect #: PS972325
Manufacturer #: 8194001
This part is a door balance link kit, also sometimes known as door cable or door spring cable kit, that helps support the door as it opens and closes by connecting to the dishwasher door hinges. The k...
$32.89
  In Stock
Upper Rack Adjuster Kit - White Wheels, Left and Right Sides – Part Number: W10712395
Upper Rack Adjuster Kit - White Wheels, Left and Right Sides
★★★★★
★★★★★
(359)
PartSelect #: PS10065979
Manufacturer #: W10712395
This authentic Dishwasher Upper Rack Adjuster Kit with white wheels is a kit made up of primarily plastic and metal components, and which will require a screwdriver to install. This kit comes with all...
$42.29
  In Stock
Rack Track Stop – Part Number: WP8565925
Rack Track Stop
★★★★★
★★★★★
(43)
PartSelect #: PS11746591
Manufacturer #: WP8565925
The rack track stop on your dishwasher is designed to stop the dish rack at the appropriate place when opening and closing the rack. If your dishwasher is not cleaning your dishes properly, the rack s...
$8.14
  In Stock
Mounting Bracket – Part Number: WP8269145
Mounting Bracket
★★★★★
★★★★★
(12)
PartSelect #: PS11745496
Manufacturer #: WP8269145
The mounting bracket is sold individually, without screws. This part secures the upper side of the dishwasher to the underside of the counter or cabinet to prevent the dishwasher from moving, shaking,...
$17.04
  In Stock
Tine Pivot – Part Number: WPW10082853
Tine Pivot
★★★★★
★★★★★
(25)
PartSelect #: PS11748190
Manufacturer #: WPW10082853
The tine pivot clip, also known as the tine row pivot, is used in dishwashers and is located in the upper dishrack. At around 3 inches in length, the clip is used to keep the tine row in place in the ...
$6.34
  In Stock
Front Track Stop – Part Number: WPW10508950
Front Track Stop
★★★★★
★★★★★
(26)
PartSelect #: PS11755805
Manufacturer #: WPW10508950
This stopper is attached to the front of the top dishrack track. This stop keeps the upper rack from pulling out too far and falling from the track.
$6.54
  In Stock
Dishwasher Positioner – Part Number: WPW10195840
Dishwasher Positioner
★★★★★
★★★★★
(6)
PartSelect #: PS11750093
Manufacturer #: WPW10195840
Also known as rack adjuster. Sold individually. This is an original part from KitchenAid, Kenmore, Whirlpool, Jenn-Air, and Maytag for use with Dishwashers. The dishrack adjuster arm positioner clip...
$33.72
  In Stock
Dishwasher Dishrack Adjuster – Part Number: WPW10195839
Dishwasher Dishrack Adjuster
★★★★★
★★★★★
(4)
PartSelect #: PS11750092
Manufacturer #: WPW10195839
Sold individually. This dishrack adjuster is for dishwashers. Dishrack adjuster lets you change the height of the dishwasher's upper rack. Wear work gloves to protect your hands when installing this part.
$36.82
  In Stock
Retainer Clip - Black – Part Number: WPW10503548
Retainer Clip - Black
★★★★★
★★★★★
(16)
PartSelect #: PS11755736
Manufacturer #: WPW10503548
This part is used to hold the access panel in place. Sold individually.
$24.97
  In Stock

Questions And Answers for WDT750SAHZ0

We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.

13 questions answered by our experts.
Sort by:
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Val
February 3, 2020
Top rack of dishwasher left side the wheel broke now can’t carry weight of dishes. What is the replacement part needed?
For model number WDT750SAHZ0
Hello Val, Thank you for contacting us. I have researched the model you have provided and have found the part you are looking for is PartSelect Number PS10065979. The wheel is only sold as part of the Rack Adjuster Kit. Thank you for your inquiry, good luck with this repair!

15 people found this helpful.

Was this helpful?
Thank you for voting!
Charles
January 4, 2020
Dishwasher will fill with water. Not wash and then drain water within 5 minutes. It never sprays.
For model number WDT750SAHZ0
Hello Charles and thank you for writing. You should try a hard reset first. Go to your breaker box, turn the breaker for your unit off, wait 5 minutes and turn the breaker back on. If this does not fix this problem then your unit might need to be leveled with kit PS972325 also you need to check the door latch PS11756967 as it might be faulty and possibly needs to be replaced. We hope this helps. Please contact us anytime.

2 people found this helpful.

Was this helpful?
Thank you for voting!
Related Parts:
Joseph
January 8, 2020
Runs through its cycles until discharge of water..i hear motor running.r
For model number WDT750SAHZ0
Hello Joseph, thank you for your question. We would recommend replacing the drain pump which is PartSelect Number: PS11738151. I hope this helps.

1 person found this helpful.

Was this helpful?
Thank you for voting!
Martha
December 1, 2019
Rubber part on the bottom I guess where it drains. Rubber is ripped open.
For model number WDT750SAHZ0
Hi Martha, Thank you for your question. Based on what you described, it sounds like you are referring to the grommet, part number PS11756098 that is near the diverter shaft. If this is not the part that you are referring to, please provide us with more information and we will be happy to check on this for you.. I hope this helps. Thank you and have a great day!

1 person found this helpful.

Was this helpful?
Thank you for voting!
Norma
February 6, 2020
Gasket on soap dispenser came out of sliding cover. Is this needed for proper operation? I would think that it is needed because it is factory installed. Is there a way to replace/reinstall gasket?
For model number WDT750SAHZ0
Hello, Thank you for your question. Looking at your model number that seal is important so detergent doesn't leave out. You will need to purchase the whole dispenser assembly- PartSelect Number PS11731570. We hope this helps.

1 person found this helpful.

Was this helpful?
Thank you for voting!

Common Symptoms of the WDT750SAHZ0

[Viewing 11 of 11]
Leaking
Fixed by
these parts
Show All
Door latch failure
Fixed by
these parts
Show All
Not cleaning dishes properly
Fixed by
these parts
Show All
Door won’t close
Fixed by
these parts
Show All
Not drying dishes properly
Fixed by
these parts
Show All
Not draining
Fixed by
these parts
Show All
Will not fill with water
Fixed by
these parts
Show All
Noisy
Fixed by
these parts
Show All
Will not dispense detergent
Fixed by
these parts
Show All
Will Not Start
Fixed by
these parts
Show All
Will not stop filling with water
Fixed by
these parts
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Replaced Hinge Link
Pulled dishwasher from under counter, attached link to spring, hooked spring back into frame/chassis, threaded link through pulleys, attached other end of link onto door, reinstalled dishwasher under counter. All's well. Note-I purchased an extra link anticipating that the other one will fail. They're cheap enough.
Parts Used:
Door Balance Link Kit
  • Scott from Fort Lauderdale, FL
  • Difficulty Level:
    Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
602 of 618 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Door spring link broken
1. Open the dishwasher and remove the two plastic grommets about halfway down on either side of the opening. Then remove the two screws under the grommets.

2. Remove the kick plate under the door. May have to lower unit by turning the feet using the adjustable wrench.

3. Make sure you have enough slack in the water input line and electrical wiring that you can pull the dishwasher out about 12 inches or more.

4. There is a spring and nylon rope link on both sides of the unit. Probably just one link is broken, but the replacement comes with two, so you can replace both or save one as a spare. Look at the good side and it should be pretty self explanatory how it attaches. I found it easiest to first thread the link around the lower pulley, then attach the link to the spring, then spring to the rear support, then the link to the door.

5. Reverse (2 to 1) to reinstall the dishwasher.
Parts Used:
Door Balance Link Kit
  • Sean from Ramona, CA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers, Wrench (Adjustable)
146 of 155 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The door would drop open when it was released
This was the second time I had this problem so I knew the symptoms and remedy. The tools needed were two nut drivers a ¼” and 5/16” along with a flat pry bar and Phillips screw driver. I started by removing the lower front panel by removing the two ¼” screws on either side. The lower panel will lift up and then can be removed by pulling on the bottom. There is a flat sheet metal piece behind the front panel with insulation that can be removed very easily along with the front panel. When the front panel is removed it exposes the front legs that may need to be dropped to let you lift the dishwasher over the tile (if you have ceramic tiles). The next step would be to remove any ties to the counter top if it is attached. Mine were attached by the two straps on either side with Phillips screws. After the top is free, lower the front legs by lifting the dishwasher with the flat pry bar and threading the legs up into their holders. With the legs lifted the dishwasher can be pulled out to expose the tension springs located along the sides at the very bottom. Chances are the ropes are broken off the plastic holders that fit over the door hooks.
Remove the plastic guides by removing the 5/16” nut from the middle of the lower roller. Remember to note which hole the screw is coming from this also sets the tension for how fast or slowly the door drops. Placing the nut closer to the front will drop the door slowly and toward the back will drop the door more quickly. I placed mine in the middle hole. When the plastic guides are removed attach the nylon pope to the spring and attach to the back of the dishwasher. There is a hole located on a flat piece of sheet metal the spring will attach to at the back of the dishwasher (if it is broken). Check the other side if it is still in tact. With the spring in place weave the rope around the plastic guides then pull the springs to help get the plastic end over the door hook located at the bottom of the door. Repeat this operation for the other side (kit has a both sides covered) and reinstall dishwasher in cabinet.
Steps
1) Remove front panel (1/4” nut)
2) Release Dishwasher from Cabinet
3) Lower front legs
4) Pull Dishwasher out from under Cabinet
5) Remove Rope Guide (5/16” nut)
6) Install new Rope Guide (Supplied in Kit)
7) Attach new rope to Spring and attach spring to dishwasher
8) Weave rope through rope guide
9) With door closed pull spring to relieve tension so rope can be attached to door
10) Repeat for other side (Kit has both sides)
Parts Used:
Door Balance Link Kit
  • David from La Quinta, CA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver
118 of 123 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!