WDF110PABW2 Whirlpool Dishwasher - Instructions

The repair was easy. Getting the unit to slide out from under the counter was more time consuming.
After water and power is disconnected, tip the unit over onto one side to gain access to bottom. Look for two white composite plastic posts (insulators) about 2" long each with a single wire inside. Remove the two wire connectors then ... Read more unscrew the insulators from the old heating element using an adjustable wrench. Inside the box remove the two metal element supports and pull out the old element. Clean and dry the area in and around the openings where the new element will be re-inserted. Carefully place the new element into the holes with the included new rubber washers. Re-install the two metal element supports on the inside of box. On the bottom, re-install the two insulators to the ends of the element, do not to tighten too much to avoid over compressing the rubber washers which could cause premature cracking. Reconnect both wires and check continuity from the door mircro-switch (white-violet) lead to the (white-red) lead on Electronic Controller connector #1 (P6). The circuit thru the element should be good if the Multimeter reads 10-35 ohms. Put the unit securely back under the counter and run a test wash. Works fine now.
I do recommend, if don't know how to use a multimeter or are concerned about accessing the electronic control box; contact a professional.

I turned off the power to the dishwasher, removed the kick plate, raised the front levelers, disconnected the electric to the appliance, turned off the water supply to the appliance, disconnected the water supply, disconnected the drain system from the garbage disposal, unscrew the appliance from the countertop, then I remove the applia ... Read more nce from underneath the counter. I then tilted the appliance back and then in screwed the plastic retainers that held the heater element in place, removed the old one, replaced it with the new one in reversed the whole process

After bailing out the unit, filled filter hole with a moderate amount of Dawn dish washing detergent. Ran dishwasher twice to remove all Dawn from the unit. Had to bailout the water (and suds) from the washer both times. After the dishwasher finally drained I inserted the new filter..

Looked at other side of top rack which still had the stop. Just had to orient the direction of the stop and push it firmly onto the rack arm. Took a couple tries, but it went in and locked. Works perfectly. Inexpensive and easy fix to to very annoying problem.

The video included with this part is perfect. Unplug the dishwasher, take off the front trim piece, remove the drain hose from the pump, unclip the power, press the little clip that holds the pump in while turning it counter clockwise to remove. Then just do that in the opposite order to put the new one in. Just make sure you hear it clic ... Read more k when you twist the new one on so you know the clip has engaged. Super easy.

Soak up the water in the dishwasher with an old towel. Removed the cover under the dishwasher. Found the pump and twisted it off anti clockwise. Replaced with the new pump. Run a quick cycle, to make sure it pumped out all the water. My wife has used it several times since without any issues.

I unscrewed the dishwasher from the counter (two screws under the countertop), and pulled it out about a foot so I could access the friction sleeve. I used a needle nosed pliers to slip a spring latch off the door. Then I slipped the new friction sleeve on and reattached the spring. Tested the door. Success! Super easy. About 5 minutes of ... Read more work.

repair went smooth for the grommet. suggest a small of vasoline to ease installation of grommet

I did not relize that the drain hose was in two parts. Naturally I ordered the wrong half. So after I relized my mistake, I re-ordered the correct part. Once the correct part was received the repair was easy and went well.

Looked under machine, saw wire going to heater was burned off.Seal on heater failed, water leaked onto terminal, shorted and burned, ruined plastic terminal nut.Replaced heater and wire terminal, and nut, took minutes, works great.

Turn off breaker to dishwasher.
Remove lower basket.
Drain any water using a wet vac.
Remove bottom cover plate. Should be 2 plastic screws using flat head screwdriver.
Should be able to reach pump. Turn counter clockwise to remove.
Disconnect plug wire on pump.
Install new pump by turning clock wise.
Re ... Read more attach wire plug.
Run a wash cycle with empty dishwasher and check for leaks.
Replace cover plate.
Done.

The water valve float lever was broke. So I replaced that and the water level switch. Probably didn’t have to replace switch. Very easy!!

put new hose on, very easy.

Snapped the new stops on. It took about 2 minutes.

Ordering the part was very easy. It shipped fast and delivered over 3 days. It fit perfectly