- Home
- WD-10580BD
- Instructions
WD-10580BD LG Washer - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Noisy and drum still full of water . Will not go to next cycle.
6 of 7 people
found this instruction helpful.
-
Marshall from ROSEVILLE, CA
- Easy
- 30 - 60 mins
-
Pliers, Screw drivers
Follow the LG washer video.
Was this helpful?
Thank you for voting!
w/d repeatedly fills with water during warm or hot loads
5 of 5 people
found this instruction helpful.
-
kevin from WASHINGTON, DC
- Very Easy
- Less than 15 mins
-
Screw drivers
E. Z. hardest part (which isn't hard) was moving the appliance to reach the back, then putting the appliance back into place. the actual repair (swapping out valve) took less time than that to do.
Was this helpful?
Thank you for voting!
The pump filter leaked after cleaning it out. Would work with teflon tape, but wanted to see if a new part would eliminate the need to wrap it every time.
5 of 5 people
found this instruction helpful.
-
Sandra from Livonia, MI
- Very Easy
- Less than 15 mins
Unscrewed the old part; screwed in the new part and said a quick prayer - LOL!
The part worked great, but I wanted to mention how quickly I received the part!
I would definitely order from this company again!
The part worked great, but I wanted to mention how quickly I received the part!
I would definitely order from this company again!
Was this helpful?
Thank you for voting!
Error Code OE showed drain pump problem
5 of 8 people
found this instruction helpful.
-
Joshua from DELTA, PA
- Really Easy
- 30 - 60 mins
-
Nutdriver, Pliers, Screw drivers
I youtube searched this problem and found a video from partselect. I watched the video, purchased the part, and followed the video instruction step by step to repair the washer. Part with tax and shipping was $52.
Was this helpful?
Thank you for voting!
washer dicharge water pump
4 of 5 people
found this instruction helpful.
-
stephen from FRANKLIN, NJ
- Really Easy
- 30 - 60 mins
-
Pliers, Screw drivers
you tube it , not to hard to install
Was this helpful?
Thank you for voting!
While replacing the tub support (spider) I chose to replace the gasket.
2 of 2 people
found this instruction helpful.
-
Robert from HYDE PARK, VT
- A Bit Difficult
- More than 2 hours
-
Pliers, Screw drivers, Socket set
The spider repair and the tub seal replacement are fairly complicated, and time-consuming, but manageable with patience. I viewed the youtube video that showed the process, which gave me confidence. It entails disassembling the machine and removing quite a few major pieces. Take care with the numerous screws and bolts, and be patient and
... Read more
you can be successful. Plan a lot of time for all the steps.
The hardest part is putting the door bellows back on.
The hardest part is putting the door bellows back on.
Read less
Was this helpful?
Thank you for voting!
Water wouldn't drain
2 of 2 people
found this instruction helpful.
-
lawrence from DOBBS FERRY, NY
- Really Easy
- 30 - 60 mins
-
Pliers, Screw drivers
I followed the video. Everything worked exactly as described. i ran a quick cycle and everything seemed to be fine. Started a wash and the machine was going fine but stopped, and wouldn't drain. I thought that maybe it might be the Rotor Position Sensor assembly, which I had already purchased just in case.But first i drained the machine a
... Read more
nd checked out the pump filter. Plugged solid. I'm guessing when the pump went there must have been a lot of lint and debris in the machine. something you might want to check out, after that repair. Thanks. you guys saved me a couple of hundred dollars
Read less
Was this helpful?
Thank you for voting!
The hot water valve was leaking
2 of 2 people
found this instruction helpful.
-
christen from HUMBLE, TX
- Very Easy
- Less than 15 mins
-
Pliers, Wrench (Adjustable)
It went great. First of all, thank you Part Select for the video on how to do this myself. My home warranty company was giving me a hard time. Blah, blah, blah. A mechanic friend of mine referred me to this site. Within minutes I found the part I need and a GREAT!!!! price. Ordered it, got it super fast, fixed it my self and my second han
... Read more
d washer is no longer peeing all over the floor. Very very happy. I will definitely be a repeat customer, hopefully not anytime soon.
Thank you again for an amazing experience.
Thank you again for an amazing experience.
Read less
Was this helpful?
Thank you for voting!
Did not draw the water and did not finish its cycle
2 of 2 people
found this instruction helpful.
-
saul from NEW YORK, NY
- Really Easy
- 15 - 30 mins
-
Pliers, Screw drivers
Remove where the water pumps are and remove the one that was damaged easily
Was this helpful?
Thank you for voting!
Drain pump inoperable
2 of 2 people
found this instruction helpful.
-
Gregory from PITTSBURGH, PA
- Really Easy
- 30 - 60 mins
-
Pliers, Screw drivers
1 tilt washer back
2 remove cover plate screw from front of drain filter access panel.
3 Remove cover plate and remove 2 more mounting screws .
4 go below washer and pull down sliding clip and move pump assembly back.
5 remove wires and 3 mounting screws around pump housing
6 Swap pump and re-attch wires
2 remove cover plate screw from front of drain filter access panel.
3 Remove cover plate and remove 2 more mounting screws .
4 go below washer and pull down sliding clip and move pump assembly back.
5 remove wires and 3 mounting screws around pump housing
6 Swap pump and re-attch wires
Was this helpful?
Thank you for voting!
Washing machine stopped purging water from drum to hose
2 of 2 people
found this instruction helpful.
-
Andria from EDINA, MN
- Easy
- 30 - 60 mins
-
Pliers, Screw drivers, Wrench set
Do not pay a service company to come to your house to make this fix!!! If you have common sense, simple tools, a phone camera and some mini zip ties you can do this!
After watching a couple YouTube videos on installing a new motor I had the confidence to start the job. My biggest worry was I'd forget where a screw/part went s ... Read more o I took a lot of pictures as I disassembled. I also laid all the parts out on a table reflective of where they belonged on the machine. I learned washers aren't rocket science - YOU CAN DO THIS. The most difficult part of the fix was my washer was a different model so much of the caging was completely different than YouTube disassembly, but once I got into the machine it was fairly identical. Easily popped out the old, broken motor and inserted the new LG certified part. Reassembled in 1/2 the time of disassembly and my machine works like new:) Hoping to get another 10+ years out of this washer.
Thanks PartsSelect for the high quality certified LG part. Very nice quality and weight.
After watching a couple YouTube videos on installing a new motor I had the confidence to start the job. My biggest worry was I'd forget where a screw/part went s ... Read more o I took a lot of pictures as I disassembled. I also laid all the parts out on a table reflective of where they belonged on the machine. I learned washers aren't rocket science - YOU CAN DO THIS. The most difficult part of the fix was my washer was a different model so much of the caging was completely different than YouTube disassembly, but once I got into the machine it was fairly identical. Easily popped out the old, broken motor and inserted the new LG certified part. Reassembled in 1/2 the time of disassembly and my machine works like new:) Hoping to get another 10+ years out of this washer.
Thanks PartsSelect for the high quality certified LG part. Very nice quality and weight.
Read less
Was this helpful?
Thank you for voting!
Dishwasher would not fill
2 of 2 people
found this instruction helpful.
-
Jesse from CARNEGIE, PA
- Really Easy
- 30 - 60 mins
-
Nutdriver, Pliers
Used Youtube to look for a set of repair instructions. From start to end 35 min.
The difficult part was getting the door back on. Only 1 Youtube video I watched stated Do not remove the 2 center screws at the top. Wish I had seen that video first.
Overall very easy to do.
The difficult part was getting the door back on. Only 1 Youtube video I watched stated Do not remove the 2 center screws at the top. Wish I had seen that video first.
Overall very easy to do.
Was this helpful?
Thank you for voting!
Te error
4 of 9 people
found this instruction helpful.
-
Luis from LEHIGH ACRES, FL
- Very Easy
- Less than 15 mins
-
Screw drivers
Change the thermistor
Was this helpful?
Thank you for voting!
Broke cold water inlet while moving
1 person
found this instruction helpful.
-
Daniel from COLUMBUS, OH
- Really Easy
- 15 - 30 mins
-
Nutdriver
Replaced cold water inlet. Removed 4 water lines and 5 wires put new part in and reinstalled lines and wires
Was this helpful?
Thank you for voting!
Hot water valve was leaking
1 person
found this instruction helpful.
-
Rick from KERRVILLE, TX
- Really Easy
- 15 - 30 mins
-
Pliers, Screw drivers
After I watched the repair video for the part, it was a snap. It went exactly as the video described the steps. Hardest part was moving the washer to get behind it.
Was this helpful?
Thank you for voting!