WCC31430AW01 Whirlpool Cooktop - Instructions

I simply removed the elements and replaced the drip bowls with new ones. Put the elements back in and my stove looks %1000 better!

Unplugged burners. . . . . Removed old bowls and replaced with new. . . . . . Plugged burners back in. However, I do want you to know that I could not believe the promptness of your service and the courteous customer service person that assisted me with my problem in selecting the correct drip bowls. You are definitely a unique company!!!!

Replacing the bowls was simple, simply removing the burner units and pulling out the bowls and inserting the new ones.

The ONLY reason I am answering this questionaire is to complement Partselect.com for their incredibly fast shipping of my parts after I placed the order. I received my order within 2-3 days with normal shipping. I expected to wait at least a week or longer. Thanks again Partselect.com for being there when I needed you the most!

So often we feel inclined to contact repairmen for simple jobs. This was easy because I ordered the part by looking on the side of the range. It arrived in less than a week. I simply snap the bowls inside the correct sockets and now my stove looks new. I definitely would use this service again.

Turn off breaker in electric panel fore stove. Put screw driver into slots in front of glass top surface. Pry top up carefully until top pops up.Remove burner dial, remove two philips head screws holding switch. Lift top carefully and prop up.With new switch close remove wires from old switch one at a time and place on new switch. Place new switch back in place, securing with philips screws. Remove prop and carefully press top down until it snappes into place.Replace dial, turn breaker back on and try burner.

Lift and remove heat elements
Lift and remove Drip bowls

Replace Drip bowls and heat elements

Very easy remove the burner and instill the drip bowls

Shut off power at breaker box , pull stove away from wall , remove Phillips screws from back of range pull knob off of switch . Look to see how switch is oriented remove 2 screws that hold switch in . Remove one set of wires at a time and place on new switch in same location . Put back together in reverse order .

Pull out the range...hardest part.
Remove back panel.
Remove/install switch
PS,
This is second switch I had to replace. Try making them in the United States.

This range was easy. Only 4 screws under the front panel that allows the panel to come off. No need to pull the range out for back screws.

Replacement part was exact and worked perfect.

Turn off the circuit breaker for the range.

Remove the 4 screws under the front panel, one on each end and one one each side of the display/control panel.

Pull the bottom of the front panel out about 30 degrees and lift off the top.

Once panel is off pull of the dial knob, remove the two screws for the control and swap wires on at a time with the new one.. Reverse the procedure and all is good. You may need to use needle nosed pliers on the spade connectors if they are too tight to pull off by hand.

unplugged power took the back panel off unplugged the 5 wires removed knob by grabbing and pulling off took two screws out of front panel removed the switched put new switch in place and reversed the procedure went very smooth know problem at all any one with any kind of ability should change this switch in know time at all

Problem I had was finding the right ones to fit the stove top. Burner pans that tell you will fit most stoves, do not. After I had paid over $20.00 for some that did not fit, I got on the internet, found you, ordered the replacement parts and had them within a few days. Put them in and there you go. A perfectly happy me and a nice looking stove again.

Changing out the switch was easy. Paid attention to wire connections to avoid mixup. Removal and installation of the switch was easy. It's the back panels that gave me the most challenge. Used screwdrivers and needle nose pliers to do repair. Having a second set of hands for the two part back panel reinstall was most helpful, but can be accomplished by 1 person.
Burner works great. This is a easy DIY fix.

replaced control

I purchased an 8" canning element for my new Kenmore Stove. The ordering process was easy. I printed my order out. I did not receive a confirmation by email, however I received the part in a timely manner. I was satisfied with the process.