W20HA2C Magic Chef Washer - Instructions

Disconnected both power and hot and cold input water lines. Laid the washer on its front side for access to the bottom. Removed the small access panel from the back of the machine to remove the metal screws holding the pump in place. Removed the single drive belt. New pump installed easily, replaced the belt and access panel. Reconne ... Read more cted the power and water hoses and everything worked fine.

Changing the hinge was not difficult, but here's a hint: the top of the washer raises up if you pry it with a big screwdriver- be sure to wrap the screwdriver in a cloth so as not to scratch the appliance. Doing it this way makes it easy to access the retaining screws. You can push the wash tub to one side and reach the screws from undern ... Read more eath, but they're a tight fit and doing it that way is difficult. Overall a pretty easy repair and I'm only moderately handy.

Removed access panel to expose pump, removed drive belt, and old pump, repeated the avove steps in reverse order, tested for leaks and proper operation.

My husband took out the 2 screws in the front panel and loosen the 3 nuts from the pump.

The parts was easily removed and the entire job tooked 30 mins.

Used a water hose to syfen out the water. Placed hose in the tub. Turned outside facet to fill hose. Undid hose outside and allowed to drain. Pulled pump. Order online ( Delv fast 2 days ) .Replaced pump . Works great . Good luck with yours.

used putty knife to to raise the top, took out two screws, replaced parts , then closed the top.

removed hoses and belt. removed 3 screws that secured pump. and then removed pump. received new pump and just reversed the process to repair!

UNPLUG ELECTRICITY. I pulled out the washing machine turned the water off pulled all of your hoses from the back of the machine there may be a mess so you need some thing that will catch the water as it comes out of the hoses. On the bottom of the machine is a belt you have to remove it. Its easy just pull it off. On the back is a panel t ... Read more hat you unscrew four screws. On the water pump it self you unscrew three screws. Then for the new part you do in reverse order screw your three screws back in put your hoses back on make sure your clamps are tight around your hoses or you will have a leak. Put your panel back on. Put your belt back on. Turn your water on from the wall plug in the electricity and you are done.

Removed water lines and drain, removed back panel, removed drain lines from pump. Unscrewed 3 screws to remove pump. attached drain lines to new pump, screwed in new pump, reattached everything. Reinstalled belt (very easy, not like an altenator). done

First I got everything I needed, unplugged the washer. Using the puddy knife I freed the top of the washer by inserting the knife about four inches from each side on front. The machine is in a place where it can not be pulled out far, hence the two by fours. Remove the loose cover, reach in with the stubby and unscrew the screw on both si ... Read more des. Take the broken cover pins off the cover and install the new ones, put the other hinges in the cover, put the hole cover in place and install the one screw perside, remove wood and close the hole top, your in business , no drinking

I first changed the belt which helped but it still sounded like it was going to take off through the roof.....I did the pulley and bearing kit in hopes that it would do some good....it went really smoothly with no issues however it did not solve the problem....so it is working and I am going to just ride it out until it quits....thanks

I pulled washer out and removed filler hoses from water supply and drain hose and tilted it forward placing three short 2X4's under the washer to keep it tilted forward. Removed
back plate with nutdriver. Removed belt from pulley and disconnected the two hoses from pump with pliers. Removed three large screws from pump base with nut ... Read more driver and removed old pump. Installed the new pump in reverse order. Quick and fairly easy took about 30 minutes.

1. Remove 1 screw holding each of 2 Hinges - use T15 driver. 2. Push tub to one side to get access to each screw from underside. 3. remove & replace broken Hinge Pin from Lid with T15 driver. 4. Drive broken pin out of the Hinge with a punch & hammer. 5. Install new Hinge Pin to Lid. 6. Add a little Vaseline to Hinge Pin & slide Hin ... Read more ge Pin into Hinge. 7. Line up Hinges to holes & re-install both Hinges with Lid. Have somebody help hold the Lid in a slight angle will make re-installation easier.

Unhooked the macine pulled out for easy access .removed drive belt rear cover plate ,vaccumed remaining water out thru drain hose with wet and dry vac. Removed hose clamps and hoses .removed the three hex screws holding the pump to the base plate. The removed the old pump , Installed the new pump hoses access plate and belt . Hooked the ... Read more machine up . Worked perfect.











the

Tilted machine back, put a paint can under it and did R & R with belts.