VV209 Frigidaire Freezer - Parts

This refrigerator defrost thermostat is a genuine OEM part and is sourced directly from the manufacturer. Located on the back wall of the freezer section in the refrigerator, the defrost thermostat is used to regulate the appliances temperature to keep the refrigerator cold and constant. The part is made of plastic, and has a 4 inch termi...Read morenal on the white lead and a 6 inch terminal on the red lead. A refrigerator defrost thermostat may need to be replaced if the appliance is experiencing temperature related issues such as: too cold, too warm, frost buildup, not running, or running too long.

This is a 120 volt defrost timer manufactured for refrigerators. The defrost timer manages the automatic defrost systemin the unit. It acts like a clock by switching between activating the cooling cycle and the defrost heater to maintain the set thermostat temperature, preventing the unit from being too warm or cold. The defrost timer may...Read more need to be replaced if the fridge will not maintain its temperature or has frost buildup. Depending on the model, it could be located on the rear panel or ceiling of the fresh food compartment. Be sure to disconnect power to the refrigerator before replacing this part.

This evaporator fan blade is a genuine OEM part that is sourced directly from the manufacturer. The evaporator fan blade circulates air through the refrigerator to control the amount of cold air goes that goes to internal compartments of the unit. It may need to be replaced if the fridge is noisy or not cold enough. This part is made of p...Read morelastic and is sold individually. It will be necessary to disconnect power to the refrigerator and empty the freezer compartment of the refrigerator. The tools needed to complete this repair are a 1/4 inch nut driver and a pair of needle nose pliers.

This part could be found underneath a fridge, dryer, or freezer. The original foot may be cracked, broken, or perhaps missing altogether. If you notice the appliance is uneven to the floor or wobbling, it may indicate that the levelling foot needs to be replaced. You will need pliers and a block of wood to perform this task. There will be...Read more one adjustable foot found in the package. Lift the dryer and place the wood to keep it propped up. You may need to use the pliers to remove the old foot. Screw the new foot into place using your hand. Once the new leveling foot is in place, lift the appliance and remove the block. Test the machine out to ensure it is now sitting level.

Sold Individually.

A filter-drier in a refrigerator has two essential functions. The first is to absorb system contaminants, such as water, which can create acids. The second is to provide physical filtration. This means trapping moisture, small metal chips, and dirt found in the refrigerant gas. If your refrigerator motor is constantly running, but the ref...Read morerigerator is not getting cold, the issue could be due to a damaged or faulty filter-drier. Faulty filter-driers are sometimes the cause for abnormal freezer compartment temperatures and partially frosted evaporators. This filter-drier is approximately 11 inches long. Remember to disconnect the power from your refrigerator before beginning this repair.

The compressor start relay attaches to the compressor in your refrigerator. If your refrigerator will not start, one of the most common parts to fail is the compressor start relay. Sometimes called the controller, this device is used to boost the compressor until the unit is running. Other common symptoms connected to start relays include...Read more: refrigerator will not start, will not cool, is making a clicking, humming or buzzing sound, or the compressor itself is warm to the touch. You may also smell a burnt plastic odor if the relay has failed. Shake the relay and listen for any rattling, as this is a sign that it is faulty.

This evaporator fan motor is located in the back of the freezer, and circulates air over the refrigerator coils. These coils will convert the heat into cool air, which is then circulated.

This gasket goes around the evaporator cover to help prevent air from going around the evaporator coil.

This strap is designed for use with the evaporator in your refrigerator. The function of this part is to hold wires, tubes, defrost heaters and other parts in place. If you notice that any of these parts are not held in place properly, you will most likely need to replace the refrigerator strap. This part is made entirely of thin metal. T...Read morehe part is very bendable, and the smaller end is designed to fit inside the large one. This part is sold individually. It is an OEM part sourced directly from the manufacturer. Many of our customers have rated this repair as easy.

This refrigerator compressor is a key component in the cooling system, responsible for compressing and circulating refrigerant gas throughout the appliance. It increases the pressure and temperature of the gas before sending it through the condenser coils, where heat is released and the gas condenses into a liquid. The refrigerant then tr...Read moreavels to the evaporator, where it expands and evaporates, creating a cooling effect that is distributed throughout the refrigerator. A malfunctioning compressor can lead to poor cooling performance or complete system failure. Proper lubrication and cooling are essential for maintaining its efficiency and extending the life of your appliance.