VT636200 Campbell Hausfeld Compressor - Parts

Designed for use in compressors, this genuine replacement part is used to provide a seal and prevent leaks. It is red, made of rubber, is not part of a kit or assembly, and is sold individually. When this part is worn, you will notice leaks from your machine, and it will need to be replaced. As with most rubber seals, this part is known...Read more to wear with regular use of your compressor, and will no longer be able to properly seal when it needs to be replaced. It is found at the bottom of the air tank, and you will need a wrench to complete this repair. Customers rate this repair as Easy.

This is an original manufacturer approved replacement air filter assembly which is specially designed for use with Campbell Hausfeld air compressors. Its purpose is to ensure the air that goes into the engine is free of dust and other harmful contaminants, over time it may get dirty and clogged eventually requiring replacement to maintain...Read more good air flow. This part consists of a durable metal housing with a pleated paper filter element.

This is a genuine OEM sourced replacement part used on Campbell Hausfeld air compressors. Its purpose is to filter out dust and debris from contaminating the engine. This filter is made out of paper and metal. This item is sold individually. To replace this you would need a wrench to remove the air cleaner cover.

Genuine Campbell Hausfeld replacement part, this item is sold individually. The ST033001AV Compression Nut is used to attach the copper tubing to certain components of the compressors listed below. Along with the Compression Nut you will need to use a compression sleeve ( or Ferrule) to seal the tube from leaking air. The Compression Nut will go on the tubing first then the Ferrule will slide into the nut.

It is a genuine OEM part that is made for Campbell Hausfeld air compressors. The unloader valve is an important component which allows a user to safely drain the air from the tank. Unfortunately, over time it may wear out or get damaged eventually requiring a replacement to ensure your unit operates properly. Note, this high-quality unloa...Read moreder includes multiple parts however it is sold as an individual component. Check the owner\\\'s manual and the diagrams of your model to ensure the correct installation and application. You will need a wrench set and pliers to perform this repair.

Sourced directly from the manufacturer, this plug is an exact replacement part for a variety of air compressors. This part is sold individually, not as part of a kit or assembly. It is gold, made of metal, and will be found on the pressure switch. This part will leak when it has become defective and will need to be replaced if it is dam...Read moreaged or worn. When you install the part, apply Teflon tape to the threads before tightening it in place. You will need a wrench to complete this repair. Customers rate this repair as Easy.

This is a genuine Campbell Hausfeld replacement drain valve, sold individually. When using an air compressor, moisture naturally condenses inside the tank. If this water is left sitting for too long, it can lead to internal rust and damage. The drain valve allows you to release this built-up moisture easily. It's especially important to d...Read morerain your tank after each use—particularly if you tend to leave air in the tank for extended periods. Regular draining helps extend the life of your compressor and maintain its performance. Be sure to open the valve regularly to prevent water buildup and potential tank corrosion.

1/4

This genuine OEM replacement nipple is designed for use in air compressors, serving as a critical connector between the pressure switch, the tank, and the regulator. A damaged or corroded nipple can lead to air leaks and inconsistent pressure, affecting overall performance. To check for leaks, apply soapy water to the fittings around the ...Read morepressure switch and watch for bubbles. If replacement is necessary, the process typically involves disassembling the pressure switch. Begin by draining the tank using the valve at the bottom, then remove the coupler from the regulator and unthread the nipple. Access the wire connections by removing the pressure switch shroud, and carefully note the position of each wire before disconnecting them—starting with the motor wire, followed by the cord wires and ground wires. Remove the strain relief, pressure gauge, and the airline connecting the check valve to the switch. Finally, unthread the pressure switch from the tank nipple and remove the nipple itself. When reassembling, it is recommended to use thread tape to ensure a proper seal. This replacement part is sold individually.

It is an authentic replacement item that is specially supplied by original equipment manufacturer for use with Campbell Hausfeld air compressors. This is the push-in fitting for the check valve which is sold separately. It is a quick-connect style fitting that is designed to accommodate for 1/4

This is an authentic replacement part manufactured for use with Campbell Hausfeld air compressors. The check valve works with the unloader valve and is used to prevent air from exiting the tank when the unloader is draining air trapped in the cylinder over the piston. A faulty check valve would allow air to exit the tank through the unloa...Read moreder, and the motor would then switch on to raise the pressure in the tank, and this could potentially burn out the motor. This unloader valve is sold as an individual replacement part.