- Home
- VCRC3016AWF
- Instructions
VCRC3016AWF Frigidaire Range - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Bottom burner wouldn’t heat
5 of 8 people
found this instruction helpful.
-
cynthia from SEBRING, FL
- Really Easy
- Less than 15 mins
-
Screw drivers, Wrench (Adjustable)
Watched the video
Was this helpful?
Thank you for voting!
Oven was not heating up properly
4 of 5 people
found this instruction helpful.
-
Robert from GILROY, CA
- Really Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers
I followed the video on the website. The probe is on back of the oven. Just unplug part and replace. That was not our fix all though as I later found that the igniter was not working. The igniter is also an easy fix but you access it through the front of the oven. Also an easy swap.
Oven is working great now.
Our iss ... Read more ues kind of fell between two of the descriptions so I went with high percentage cheaper fix first.
If your oven is intermittingly getting hot or to temperature of 100, it is probably the igniter.
Have used PartsSelect for Washing Machine, Dryer, Refridgerator and now the Range. Super easy to figure out needed parts and videos walk you through the repair.
Thanks
Oven is working great now.
Our iss ... Read more ues kind of fell between two of the descriptions so I went with high percentage cheaper fix first.
If your oven is intermittingly getting hot or to temperature of 100, it is probably the igniter.
Have used PartsSelect for Washing Machine, Dryer, Refridgerator and now the Range. Super easy to figure out needed parts and videos walk you through the repair.
Thanks
Read less
Was this helpful?
Thank you for voting!
F10 code going off
4 of 5 people
found this instruction helpful.
-
edward from BRISTOL, IN
- Really Easy
- 30 - 60 mins
-
Screw drivers
Went well, and working thank you ??
Was this helpful?
Thank you for voting!
Unable to close oven door; door hinge needed to be replaced
3 of 3 people
found this instruction helpful.
-
Alan from WAPPINGERS FL, NY
- A Bit Difficult
- 30 - 60 mins
-
Screw drivers
Remove oven door and place on soft surface
Remove 2 Door Handle Screws
Remove 4 Inner and Outer Door Panel Screws
Remove Door Hinge Screws and remove door hinge
Install new hinge by aligning with holes and secure with screws
Re-join inner and outer door panels
Replace door handle
Replace bottom screws
Remove 2 Door Handle Screws
Remove 4 Inner and Outer Door Panel Screws
Remove Door Hinge Screws and remove door hinge
Install new hinge by aligning with holes and secure with screws
Re-join inner and outer door panels
Replace door handle
Replace bottom screws
Was this helpful?
Thank you for voting!
Bake elemen t shorted out.
3 of 3 people
found this instruction helpful.
-
LARRY from LEES SUMMIT, MO
- Really Easy
- 30 - 60 mins
-
Screw drivers
Turned off power to stove;removed baking racks , loosened Holden screws to pushon bake element removed old bake element,installed new pushon bake element.
Was this helpful?
Thank you for voting!
Bake element went out
4 of 6 people
found this instruction helpful.
-
Nicholas from COTTONDALE, AL
- Really Easy
- Less than 15 mins
-
Socket set
The broil element and range were both working so I removed the bake element to test for continuity. Use a 1/4” socket or wrench to remove the two screws holding the bake element to the rear wall of the inside of the oven. Pull the ends of the element out of their recesses taking care not to lose a wire inside the back panel of the oven. P
... Read more
ull the wires off the element ends. You should be able to do this by hand; use a flathead screwdriver for a little prying if necessary. Visually inspect the element for physical damage. If you don’t see any, test the element with an ohmmeter or multimeter. If it reads anything other than 0 ohms (continuity), your element is defective. Installation process is reverse of removal.
Read less
Was this helpful?
Thank you for voting!
Oven would not heat
3 of 3 people
found this instruction helpful.
-
Kevin from Swanville, ME
- Very Easy
- 15 - 30 mins
-
Screw drivers
Pulled stove away from wall and unplug .Removed grates for better access. Unscewed element scews removed element & tested for continuity.there was none element is bad . Replaced with new one . Time about 20 minutes.
Was this helpful?
Thank you for voting!
Oven wasn’t heating
3 of 3 people
found this instruction helpful.
-
Felicia from FORT MILL, SC
- Very Easy
- 15 - 30 mins
-
Nutdriver
Used instruction video & replaced part.
Was this helpful?
Thank you for voting!
Bake element began burning itself up.
3 of 3 people
found this instruction helpful.
-
Don L from La Grande, OR
- Really Easy
- 15 - 30 mins
-
Nutdriver
Originally I had anticipated a major problem requiring the removal of the back of the range and perhaps the necessity of employing the services of a repairman ($$!). Fortunately I waited for the arrival of the replacement element, which, upon inspection, was not configured to go through to the back of the range. What a relief!
... Read more The hardest part of the repair was finding the correct nutdriver (5/16"). Removal of the damaged element was simply backing out the two retaining screws inside the oven and pulling the element out far enough to expose the clips to the wire. Pulling them apart was easy enough, and then the element I disposed of immediately.
Reverse of removal of the old element was the installation of the new: Reconnect the clips to the element, push the wires back into the insulation, re-inserting the two retaining screws and tightening them gently.
The final step was to plug the range 220 cord into the outlet. Testing whether the element was functional was a breeze; the oven and the range elements worked perfectly.
... Read more The hardest part of the repair was finding the correct nutdriver (5/16"). Removal of the damaged element was simply backing out the two retaining screws inside the oven and pulling the element out far enough to expose the clips to the wire. Pulling them apart was easy enough, and then the element I disposed of immediately.
Reverse of removal of the old element was the installation of the new: Reconnect the clips to the element, push the wires back into the insulation, re-inserting the two retaining screws and tightening them gently.
The final step was to plug the range 220 cord into the outlet. Testing whether the element was functional was a breeze; the oven and the range elements worked perfectly.
Read less
Was this helpful?
Thank you for voting!
Burnt out baking element
3 of 3 people
found this instruction helpful.
-
Joseph from HAMPTON, VA
- Really Easy
- 15 - 30 mins
-
Nutdriver
Removed the back panel, disconnected the terminals and removed the old one and installed the new one.
Was this helpful?
Thank you for voting!
Repaired Oven Range Light Bulb
3 of 3 people
found this instruction helpful.
-
Alan from SAN MATEO, CA
- Very Easy
- Less than 15 mins
-
Screw drivers
The bulb has a plastic clear cover. That cover can just be carefully removed using a screwdriver. It's held in by a metal bracket. After you remove the cover. You'll just need to replace the bulb and then re-install the cover and bracket.
Was this helpful?
Thank you for voting!
the old bake element was corroded and non-funtional
5 of 9 people
found this instruction helpful.
-
Stephen from RONAN, MT
- Really Easy
- Less than 15 mins
-
Screw drivers
Using a socket set and Robertson #3 (smallest) driver head,with the breaker shut off before working I removed the old element and disconnected the old element from the wire connections.I then installed the new element by connecting the terminals to the wire connection in the range before screwing the old retaining clips to the back of the
... Read more
oven compartment wall.Then I flipped the breaker switch back on and turned on the oven dial to 425 degrees to see the element heat up and glow red affirming the success of the repair.Total time to repair about 15 minutes.
Read less
Was this helpful?
Thank you for voting!
Change on e of the inside glass
4 of 7 people
found this instruction helpful.
-
Ronald from Ozone Park, NY
- Easy
- 1- 2 hours
-
Screw drivers
removed the screws holding the front part of the door and from there worked my way, untill the third glass.
It took a couple hours, my first time,. Overall easy,
It took a couple hours, my first time,. Overall easy,
Was this helpful?
Thank you for voting!
Bake Element caught on fire
4 of 7 people
found this instruction helpful.
-
Judy from Spencerville, OH
- Really Easy
- Less than 15 mins
-
Nutdriver, Screw drivers
First we turned off the electic, then we took the back off the stove and pulled the wire off the bad element then replace the new element. It was very easy to do.
Was this helpful?
Thank you for voting!
Broiler broke apart in pieces. Also we found an round honeycomb part
3 of 4 people
found this instruction helpful.
-
Betty from KNIGHTDALE, NC
- Really Easy
- 30 - 60 mins
in the bottom of the oven when I was looking to see what was going on. My husband did the repair just as the video described. I suspect this part honeycomb round maybe ceramic piece goes over where the heat is vented from the oven. Where do I get another one of these and how does it attach in the oven-under t
... Read more
he burner. HELP I tried to look on the schematics and did not see anything. The repair went fine, except when we turned everything back on it did not work. Then my husband remembered he forgot to plug the new part IN. Once plugged in it is working fine. Thanks
Read less
Was this helpful?
Thank you for voting!