UT905011 Homelite Generator - Parts

This inline fuel filter is a genuine OEM part designed for use with pressure washers and generators and is sold as an individual part. Made of plastic, this filter is used to prevent dirt and debris from entering the carburetor and engine of your equipment. Regular maintenance, routine inspections, and replacement of this part will help t...Read moreo prevent any issues with your equipment in the future and ensure best performance. If your equipment is experiencing starting issues or you notice blue or dark-colored smoke coming from your equipment, the filter may need to be replaced. To replace your current filter, gain access to the fuel line or tank, restrict the flow of fuel through the filter, and simply remove it before replacing it. If your filter needs replacing, check your fuel lines for any clogs or debris build-up.

This fuel shut-off valve, also known as a fuel valve or fuel selector valve, is an OEM replacement part designed for use in generators. The valve controls the flow of fuel to the engine. When the valve is in the on position, fuel flows to the engine, enabling it to run. When the valve is in the off position the flow of fuel stops and the ...Read moregenerator shuts down. Over time the valve may become clogged or damaged, and unable to fully close or open. Once the fuel shut off valve is no longer functioning, the generator will leak fuel, and may have difficulty in starting or running. Before replacing the valve, first disconnect the fuel line and place a container below the fuel tank to allow the fuel to drain out. Detach the old fuel shut off valve and install the new one in its place. Apply thread sealant to the new valve for a good seal and reattach the fuel line. Refill your tank with fresh fuel and run the equipment to ensure there are no more leakages.

This is a genuine OEM sourced replacement part that has been sourced from the original manufacturer to be used with portable generators from Homelite and Husky. The carbon brush is used to relay electricity from the generator head. This item is sold as an individual replacement part.

This authentic manufacturer-sourced part is specially designed for use with portable generators. It is an identical replacement for a missing or a faulty component that was installed on a new unit. The part helps to secure fuel tank to the main frame, please make sure to refer to the appropriate diagrams of your model for the correct loca...Read moretion and application of this hardware. Keep in mind this high-quality isolator is made of durable rubber and is sold individually.

This is a genuine Homelite, Ridgid, and Ryobi replacement part for use in generators. The fuel cap attaches to the fuel tank. No tools should be needed during the replacement of this part. It is made out of metal and will need to be replaced if it breaks. This item is sold individually.

The fuel tank vapor vent attaches to the bushing rollover valve and the fuel tank. This is a genuine Homelite and Ridgid part sourced directly from the manufacturer for use in generators. It is sold individually and is made out of plastic. During the installation process, a wrench and a set of pliers might be needed to replace this item. This part will need to be replaced if it breaks.

This is an authentic Homelite replacement part. The outlet cover is designed by the manufacturer for use in portable generators. This part is made of flexible rubber, and is attached to the cover plate to protect the duplex receptacle outlets when not in use. You will require a screwdriver when replacing this part. This item is sold individually.

This authentic item is supplied directly from the original equipment manufacturer for use with pressure washers and generators. The wear pad is made of hard rubber and attaches to the foot bracket with a washer and a bolt. It may require a wrench during replacement if the part becomes broken. The pad is sold individually and helps to reduce vibrations and cushion the bracket.

This replacement automatic voltage regulator is sourced directly from original equipment manufacturer for use with Homelite and Ridgid generators. It regulates the output voltage of the generator by limiting the amount of voltage in the electrical system. Please note this high quality item is sold individually.

This is an authentic manufacturer-sourced replacement washer which is specially designed for use with pressure washers. The purpose of this part is to provide a tight seal between connected components, over time it may wear out or simply get lost eventually requiring a replacement. Please make sure to refer to the appropriate diagrams of ...Read moreyour model for the correct location and application of this hardware. Keep in mind this high-quality washer is made of durable metal and is sold individually.

This is a genuine manufacturer-sourced replacement lock nut which is specially produced for use with pressure washers. A lock nut is a type of nut that resists loosening when properly threaded onto a bolt, please make sure to check appropriate diagrams of your model for the correct location and use of this hardware. Not this high-quality component is made of durable metal and it is sold individually.