UT08514 Homelite Leaf Blower / Vacuum - Parts

The OEM Air Filter is used to stop debris and particles from entering the carburetor and engine, which could cause damage. It is attached in the air filter housing. It comes in black, and is contructed from foam. Installation is rated as "Easy" by customers, and will require a screwdriver. (Tip: You can place the filter in a plastic bag w...Read moreith a bit of oil, remove it, and then squeeze the filter to drain the excess oil. The remaining oil will work as a sticky trap). If the part becomes worn over time, the engine will be hard to start and will run rich. In this case, replace the part. Refer to your make, model and diagram to ensure this is the correct part for you.

This OEM spring, also known as a recoil or rewind spring, is housed in a container and is used to retract the starter rope on various lawn equipment models. Over time and through use, the spring will eventually lose its tension, and will break. If your starter rope has no resistance when pulling it, the starter spring is likely broken. Me...Read moreasuring at approx. 3-inches by 3-inches, this spring is suitable for use with a variety of lawn equipment models and is sold individually.

This crankcase cover gasket seals the crankcase cover of your lawn equipment engine, preventing air or fuel leaks and maintaining proper internal pressure. It is sized at 2 1/2 inches by 2 1/2 inches and is commonly found where the crankcase cover attaches to the engine block. You can tell if a crankcase cover gasket is broken if there is...Read more oil around the edges of the cover. Your machine may also experience a loss of power or unusual noise. If the gasket is not replaced, your machine may have fuel leaks or decreased performance. Debris and contaminants will also enter the engine, reducing the lifespan of your machine. When replacing the gasket, use a wrench or socket to unthread any bolts securing the crankcase cover. You will then be able to take the gasket off your machine. Bear in mind that this OEM gasket is sold individually.

Genuine OEM replacement part, this item is sold individually. This Fuel Cap is is on the fuel tank on the outdoor products shown below. This is a vented Fuel Cap. It includes a gasket inside the Cap.

This is an OEM replacement part,it is sold individually. The purpose of the Air Purge Bulb is to purge all of the air from the carburetor. It then brings fuel up through the fuel line in the tank into the carburetor. Once the carburetor is full of fuel the Bulb will force the excess fuel back into the tank through the fuel return line. ...Read moreOver time the bulb will loose it elasticity or begin to crack, it will need to be replaced at this time.

This item has been OEM sourced and is intended to be used with gas-powered trimmers and pruners from Ryobi & Homelite. The gasket is used to seal the connection between the cylinder and the crankcase. It is recommended to replace gaskets when servicing the motor to ensure proper seals and spacing when the parts are reassembled. This item is priced as a single part.

The choke lever is part of the air box base assembly. This authentic item is supplied directly from the original equipment manufacturer for use with blowers, trimmers, and vacuums made by Homelite, Toro, and Ryobi. This part is available individually and is made of plastic. During the installation process, a screwdriver and a wrench might be needed to replace this item. It will require replacing if it becomes broken.

This item has been OEM sourced to ensure a high-quality standard. The rotor is intended to be used with trimmers, blowers, and chainsaws from Homelite and Ryobi. The rotor is the engine's flywheel and is used as one of the main components in the ignition sequence. The rotor has magnets on its edge that create an electric charge as they pa...Read moress the ignition module, this ignites the air/fuel mixture in the cylinder which rotates the crankshaft and the drive shaft. This item includes the pawls that make contact with the recoil starter pulley when the starter rope is pulled.

This rope is part of the pull starter system on Homelite and Ryobi gas powered lawn and garden equipment. It is an authentic manufacturer sourced replacement part, not an aftermarket equivalent. When the rope is pulled to start the engine, it is returned back into the starter pulley by means of the starter spring which is sold separately....Read more Please note, this rope is made out of strong fabric and it is sold individually. Replacing this starter rope you will need a screwdriver. • Remove the housing-cover • Remove the carburetor • Disconnect the clutch housing • Bind the engine • Remove the clutch drum • Remove the clutch • Remove the starter • Remove the starter handle • Remove the recoil pulley • Remove the old rope • Install the new starter rope • Reassemble and test the unit

It is an authentic OEM sourced replacement item designed for use with Homelite and Ryobi handheld lawn and garden equipment. The ignition module also known as an armature-magneto provides an electric current for the ignition system. It produces high voltage pulses for the spark plugs. It is made out of metal with a rubberized wire and a spark plug boot. Please note, this ignition module is sold individually.