UT-20581-1 Homelite Trimmer - Parts

This spool retainer is sourced from the equipment manufacturer for use in trimmers. It is a plastic knob, measuring 2 inches in diameter, with a threaded metal bolt in the center. The retainer has a right hand thread, and it is used to secure the spool within the trimmer head to prevent it from coming loose during operation. The retainer ...Read moreengages with the trimmer head to lock the spool in place, while it also advances the cutting line for greater cutting efficiency. If the threads on the retainer bolt wear out or the plastic body becomes damaged, the retainer will be unable to engage with the trimmer head, causing the line to tangle, the spool to come loose, and lowering the cutting performance of the trimmer. Remove the trimmer head cover and detach the retainer from the assembly. Position the new spool retainer in the assembly and thread it firmly into place.

This is a genuine OEM replacement part, sold individually. This Bumper helps keep the fuel tank in place, and minimizes vibration of the fuel tank. This part is used with a variety of string trimmers, compatible with the models listed below.

Springs are used within outdoor power equipment to provide tension and shock absorption, depending on their application and use. This spring is designed for use within trimmers/brush cutters and is made to provide tension on the spool reel mechanism, and in some cases may be used to advance the line whenever portions of it are cut off. Th...Read moreis spring measures approximately 1.3-inches in length when extended and comes as an individual part. If you notice the line/spool in your trimmer is not advancing or is coming too quickly, the spring may be damaged and need replacing. Since this spring is a high-use part, it is not uncommon for it to lose tension over time and need to be replaced. To replace the spring, you will need to unscrew the covering cap, remove the spool feeding reel, remove the old spring and install the new spring with the rest of the assembly. Make sure to feed the line back into the appropriate feeding holes prior to operation of the trimmer.

This is an OEM replacement part. It has a left hand threaded screw to remove and attach it to the trimmer head. Its purpose is to hold the spool with the cutting line, in the spool housing. It also acts as the bumper to advance the line from the spool. This is a well used and abused part of the trimmer. It may be a good idea to order an extra one.

This is a Manufacturer Sourced replacement part for Lawn and Garden equipment. This item is Metal an is Sold Individually. A lock nut is a type of nut that resists loosening when properly threaded onto a bolt. This Locking Nut secures the cutting blade on the Trimmers/Brushcutters. You would need a Wrench to tighten or loosen this Hex Nut.

This is a genuine OEM sourced replacement starter rope, not an aftermarket equivalent. This part is used to pull start Homelite and Ryobi handheld lawn and garden equipment. This rope is made from durable fabric and it is sold individually. Please note, the grip handle is sold separately. Replacing this starter rope you will need a screwdriver.

It is a genuine item that is supplied by the original manufacturer for use with Ryobi and Homelite handheld string trimmers. This washer-clutch is a special friction disk that helps to engage the clutch by ensuring a tight fit between connected components. It provides an identical replacement for a damaged or a missing hardware that was i...Read morenstalled on a new unit. Check the diagrams of your model for the exact location and the correct installation of this part. One durable metal washer is included. You may need a screwdriver and a wrench set to perform this repair.

This metal OEM wire clamp is a type of fastener that holds hoses or cables together and keeps them from moving while your machine is operating. It is mostly found in lawn equipment to attach its fuel line to the filter. You can tell that the metal clamp is broken if the parts it was securing has become loose or has fallen off. When this h...Read moreappens, your equipment may start leaking and can pose as a safety hazard. To remove the wire clamp, you need a pair of pliers. Grip onto a broken clamp before twisting it counterclockwise to release it from your machine. This item is sold separately.

This starter pulley is an OEM part direct from Ryobi. This part is compatible with a variety of lawn and garden devices. The pulley is most often fitted between the air baffle and the container w/spring within the starter assembly. Please consult specific manual and diagrams for repair instructions. This part is sold individually. A screwdriver and a hex key are usually needed in making the replacement.