UT-15089-D Homelite Trimmer - Parts

This is a genuine OEM replacement part, sold individually. This Bumper helps keep the fuel tank in place, and minimizes vibration of the fuel tank. This part is used with a variety of string trimmers, compatible with the models listed below.

This flanged star washer is a manufacturer-sourced replacement part designed for use trimmers. It is also known as a tooth lock washer due to its serrated inner edge which resembles inward facing teeth. These teeth bite into the head of the fastener and provide a better grip than standard washers. This washer also has a flange on one side...Read more which is a lip that extends past the edge of the washer. It helps to distribute the load of the fastener over a wider area to provide extra stability and a more secure hold. Over time the washer may wear down or become damaged. To remove the washer, first unthread the bolt/screw it is fastened on. Use pliers to grip the washer and gently twist it off. Place the new washer over the fastener with the teeth facing toward the surface being fastened and insert it into the designated hole. Ensure that it is locked into place. Each washer is sold individually.

This is a genuine OEM replacement part, it is sold individually. The purpose of the 900994004 Carburetor Gasket is to prevent an air leak, which would cause the engine to run poorly. It is advised to replace these gaskets when replacing or repairing the carburetor.

This item has been OEM sourced and is intended to be used with gas-powered trimmers and pruners from Ryobi & Homelite. The gasket is used to seal the connection between the cylinder and the crankcase. It is recommended to replace gaskets when servicing the motor to ensure proper seals and spacing when the parts are reassembled. This item is priced as a single part.

The cupped washer attaches to the tri-arc blade with the use of the lock nut. This part is an OEM from Ryobi and Homelite to be used in brushcutters and trimmers. It is made of metal and helps to keep the cutting tool in place. A wrench will be needed if this part needs to be replaced. This washer is priced as an individual replacement part.

This is a genuine OEM replacement strap made for various yard tools. This fabric strap features one metal lobster clasp, which attaches to the tool via the strap hanger. It is adjustable with a plastic slide adjuster. One strap is included.

This is a manufacturer approved replacement part designed for use with gas string trimmers. This tube is the fuel return line that returns fuel back into the fuel tank after the carburetor has been primed. It is made out of rubber and it is sold individually.

A genuine replacement part which is supplied directly from the original equipment manufacturer for use with Homelite and Ryobi handheld lawn and garden equipment. Please make sure to refer to the appropriate diagrams of your model for the correct location and application of this hardware. Keep in mind this high-quality screw is made of durable metal and is sold individually.

It is a genuine item that is supplied by the original manufacturer for use with Ryobi and Homelite handheld string trimmers. This washer-clutch is a special friction disk that helps to engage the clutch by ensuring a tight fit between connected components. It provides an identical replacement for a damaged or a missing hardware that was i...Read morenstalled on a new unit. Check the diagrams of your model for the exact location and the correct installation of this part. One durable metal washer is included. You may need a screwdriver and a wrench set to perform this repair.

This metal OEM wire clamp is a type of fastener that holds hoses or cables together and keeps them from moving while your machine is operating. It is mostly found in lawn equipment to attach its fuel line to the filter. You can tell that the metal clamp is broken if the parts it was securing has become loose or has fallen off. When this h...Read moreappens, your equipment may start leaking and can pose as a safety hazard. To remove the wire clamp, you need a pair of pliers. Grip onto a broken clamp before twisting it counterclockwise to release it from your machine. This item is sold separately.

This is a genuine OEM replacement part, it is sold individually. This is the fuel return-line it is connected from the fuel tank. It is then connected to the carburetor. It is used on the model numbers shown below.