UL2500CA2 Electrolux Freezer - Instructions

This freezer has many screws that hold the cover on the back of the door and assist clamping the edge of the gasket in place. Be sure to just loosen the screws 3/4 the way out, use a flat head screw driver to pry the cover from the door in case over time it is stuck to the door. The new gasket will come in a creative box trying not to kin ... Read more k the gasket itself, but there will be some distortion of the gasket when you get it. Put it in the sun or in hot water. I put it in my dryer for 10 minutes. Remove the old gasket, and start at the top of the door to replace the gasket. TIPS: If the screws are backed out enough, there should not be any problem sliding the back part of the gasket under the cover. When on the sides, do not pull the gasket down to make it easier to slide the gasket underneath the cover. This will distort and lengthen the gasket so it will not fit and thin it out so it will not function well. Once the gasket is in place, tighten the screws being sure to feel along the outside edge of the gasket for any bulging that would indicate that portion of the gasket is NOT under the cover properly.

I accidently threw away both freezer keys to our upright Gibson and G.E. Freezers!!!! I had no luck finding replacements locally, so I got on the internet and came across PartSelect.com. I called them on the telephone; and after giving the model numbers of my freezers, the keys were on their way!! I received the keys very quickly and bot ... Read more h worked perfectly. I would highly recommend Partselect.com. Charlotte M. Bishop

We ordered the part, which was a key, tied it on the freezer door handle, locked the door and voila, the problem was fixed. (We still have the children. :-)

Pretty straight forward. Loosen all screws "but do not remove" pry door panel from door just enough to slip gasket behind panel. Make sure gasket is seated properly around door.. Tighten all screws snug...

Gasket may not seal right away due to being kinked from packaging, use a little heat on gasket witth hairdryer and push so ... Read more mething heavy against door over night. The gasket will straighten out over night.

Bought a new
capacitor.

This was a simple job. Raised the flap in the back that houses the compressor, removed the wire that holds the relay, pulled out the old relay and pushed the new one on. Replaced wire holder and that was it. Plugged it frig and freezer is at zero and lower compartment at 35. As easy as brushing your teeth!

I located the part that was the culprit as it had buzzed very much before quitting. This is an easy removal as the part is in a two prong jack and just needs to be carefully removed with the new part inserted back in the jack provided. The refrigerator works fine now, but the run capacitor will still buzz on start up of the compressor. I ... Read more do hope this is normal in this model? anyway it runs fine mow. Thank you.

Removed the numerous screws and took the door panel off. Cleaned and dried it. Replaced the insulation and hung the penal with 2 screws at the top and sides. Started to fit the gasket under the edge of the panel and put on the screws as I went across the top then down the sides finishing across the bottom. Perfect fit but could not get th ... Read more e door to seal at all. Went out and bought a new freezer(did I say it was 17 yrs old?!?!).

Had to drag the full freezer out from the wall to expose the name plate, got the Model # and S/N and found the key on the partselect website in minutes. It was cheap so I got two. Other than FEDEX not knowing my address correctly, when I finally got the key it worked fine. Not a problem anymore.
Thanks

I originally ordered an aftermarket replacement seal off intranet at half the price. It came in poor packaging & crumpled in a ball when received. After install, it would not seal & worse than the old seal that was replaced. I removed poor quality seal & returned it. I then ordered the OEM seal from PartSelect. It came in proper packaging ... Read more . I kept the inside door shelving in place with two mid screws. Beginning at top I inserted sealing grove into channel of shelving working all the way around door frame. Making sure there was no crinkles or bulges at one place & it was all even. I replaced all screws ensuring not to over tighten. Close door and made sure magnetic seal pull closed to freezer & door on both sides by sliding my finger all the way around. I did not open the door for 1 hour to ensure rubber seal had taken proper shape to freezer frame. After I worked door Open/Close many times. Door seal worked perfectly every time then and now. This is a perfect example why to buy quality parts the first time.

Purchased new freezer.

Remove door remove old gasket, put new seal in dryer for 10 minutes to help it shape better then install new gasket with about 50 screws

My issue was water leaking from the door. I thought it was the gasket, so I removed the gasket and the entire panel off of the door. There was water behind it that had soaked the cardboard seal, so I left that front part off for over a week to let it dry. We determined between us and our two toddlers that perhaps the door hadn't been prop ... Read more erly closed enough on a number of occasions, so before I bought a $100 gasket, I'd try making sure the door was shut with tape, turning the freezer on and seeing what happened. There was no water after a few days, so on another user's suggestion I purchased the $15 key and twist tied it to the freezer door. Now I am locking the door after use so we won't have leaking water any longer.

The site offers a video for this part which worked perfectly. In addition to replacing the part, since the cardboard panel was off, we also cleaned all the dust off of the coils which someone recommended to do annually.

Took out screws completely then had to wedge gasket underneath. Gasket comes a little tangled in box should remove immediately and keep at room temp till ready to use.