TUD6710PB1 Estate Dishwasher - Instructions

After pulling the dishwasher out from under the cabinet, I found it underneath near the back right side. I disconnected the old thermostat, unscrewed the clamp holding it into place, put the new thermostat in, screwed it back in and replaced the two plugs. Then I pushed the dishwasher back into place, and it initially didn't work until ... Read more I found an online forum that was able to identify the reset command for my dishwasher (for the WDT710PAYM4, press any three buttons in a sequence of 1 2 3 1 2 3 1 2 3. After completing that all the lights lit up, and I shut the door leaving it for half an hour) Once the reset finished, the heated dry worked like it was suppose to.

screwed it in with my hands

1) Removed the two white clips from the left and righ hand side of the top tray roller rail. this allows the tray to be completely removed and ease access to the washer assembly. The clipe looks like the letter "k", so you will need to close the "k" to almost straight line in order to get it through the hole.

2) Put a sheet ... Read more or a towel at the bottom of the machine, just incase you drop the two small cross head screws. This prevents the screws from falling to the bottom of the machine.

3) Remove the screws. At this time the washer assembly will/should slip out very easily. very little force is required to pull the assmbely out.

4) Slip on the new washer assembly and put the screws back in place. Tighten screws, Be careful not over tighten the screw as you may crack the plastic flange.

Note: My machine is an older model, so the washer assembly had two screw fixing. The new assembly only had one hole. Although one fixing appeared to be sufficient, I decided to drill a hole on the other side and this worked fine.

5) Replace the top tray, taking some care to ensure rollers are correctly located within the rails. Then replace the clips and job's complete.

first i picked out the old seal, use a screwdriver to get it started. Then I pushed the new one in after cleaning the seal channel. I fixed it during a commercial while watching my favorite tv show.

Simply removed deflectors and gasket, replaced all , took all of 5 mins. workes great now.

The old gasket came out easily, but had calcium deposits in area. I cleaned the area with vinegar and water and waited until it was completely dry. The new gasket went in very easily and looked great. I started the dishwasher and alas, it still leaks, so the problem was apparently not with the gasket, but some other area. But the gasket i ... Read more s nice and new. Any suggestions on next step0 in troubleshooting?

Had to use a standard flat screw driver to pry off the old mount. used a phillpips head driver to fasten the mount to the spray arm and pushed the new mount in place.

unscrewed sprayarm, removed bearing and seal, used PartSelect pic and description schematic to identify part numbers then placed order. Parts arrived in two or three days.

All I had to do is lay the shield over the top and sides and used a couple of clips to hold in place as it was slid under the counter top. It couldn’t have been easier.We had searched everywhere for this replacement shield and parts select was the the only ones that had it. Very good service and fast delivery,

Looked at other side of top rack which still had the stop. Just had to orient the direction of the stop and push it firmly onto the rack arm. Took a couple tries, but it went in and locked. Works perfectly. Inexpensive and easy fix to to very annoying problem.

replaced the rack adjusters

I first removed the old part. when i removed the old part i could not get the conector piece off when i when to get a new one they told me i should replace the copper tubing with the more flexable tubing because the copper tubing can kink up and possibly break from the kinking. so i screwed the inlet valve on i put teflon tape on the all ... Read more the threads of the conector piece screwed it into the new inlet valve with and adjustable wrench then i conected the new tubing, and tightend it down with the wrench i slowly turned the water back on to cheak for leaks. When i saw there were no leaks i turned the water on the rest of the way pushed the dishwasher back in and screwed it into place an i was done.

Pulled off the old valve using a crescent wrench and screw driver. The replacement part was a 100% exact match. Slapped on the new valve and that baby was water tight. $50 on a new valve is a lot better than $500 for a new washer.

Partselect.com was so easy to use and find the right part. Way more helpful than whirlpool's s ... Read more ite, but that's not surprising seeing as they have an "authorized repair technician" page.

Thanks Partselect.com!

Eay repair. Replacement tube was one piece and only required removing one phillip's head screw to replace

actually my wife did the repair. she unsrewed the water sprayer and removed it, then unscrewd the star key screws and then replaced the seal. she put everything back the way it was and it is now ready to use and we no longer have the problem.
just a suggestion...if you take some baking soda and some vinager you can clean the drain ou ... Read more t. just simply poor in the soda and then the vinager.and it will fiz cleaning your drain.