TR522SW-P1182701WW Amana Refrigerator - Instructions

I used a flat-head screwdriver to pop out the old light rocker switch. Then, I unplugged the wires, plugged them into the new light rocker switch, and then popped the new switch into the hole. That's it! Lights began working again.

I removed the screws holding the old, cracked handle in place, and used the same screws to affix the new handle, which fit perfectly. The whole job, including a bit of cleaning to remove the scuzz that had built up around the top and bottom of the handle over 13 years' time, took about 5 minutes. Note: the screw at the bottom is covered b ... Read more y a small plastic tab (easily removed by prying, gently, with a screwdriver), which doesn't come with the new handle, so if covering the screw matters to you, don't break or lose the old one!

Bought a replacement gasket for the Refrigerator to solve the leaking air problem. After replacing the gasket, nothing changed, so it appears the problem is the door itself, so if you have a separation between in the gasket, be sure it's the gasket and not the door itself.

An easy job for smaller hands. Removed the two bolts holding the light cover. Removed two electrical connections from the old switch by pinching the retaining clip,removed the switch, snapped in the new one and re-attached the connectors. Your online illustrations helped me to know that the plastic housing for the light switch would only ... Read more swing down so far and was not intended to be removed. Saved me from breaking that plastic cover's tabs. This home repair saved me more than 5 times the cost of hiring a professional to do it. Very happy homeowner.

First I went on line and found detailed instructions how to do it. I also covered the frig with a large piece of card board to keep the "cool" in to some degree. I put the new gasket in a tub of hot water. I unloaded the door. Loosed all the screws..pulled off old gasket/seal.... carefully put the new one on the door. This was tedious ... Read more but okay. then I tightend the screws. Closed teh door...made adjustments ..leveled the refrigerator... checked for leaks by putting a flashlight in the frig and closing the door. I also used a dryer to help the seal form easier. awesome! Like a new refrigerator.

Once I saw the replacement part I understood how to pry out the switch with a small screwdriver. Then just unplug the old one, plug in the new one and pop it into place.

The PartSelect site made it easy to correctly identify the correct part, it was inexpensive, and the shipping was fast.

I'm very pleased!

very easy.....
1. removed the food items from the shelf
2. raised the shelf and removed the broken support post
3. inserted the new support post and guided the drawer rails to rest in the new support slots
4. cleaned the glass shelf and replaced the food items
5. made my wife very happy now that the veg draw ... Read more er opens and closed like new.

Step 1: Removed door because I wanted to change the opening from left to right. Step 2: Place door on 2 saw horses and remove gasket with a nut driver. Step 3: Install new gasket. Step 4: Reinstall refrigerator and freezer doors.

I found this proceedure to be one of the easiest I have ever accomplished.

First I read other repair stories which really helped. I decided to leave the door on and use a 1/4" nutdriver plus a flat blade screwdriver. I loosed the screws on one side at a time. I pulled off the old seal and replaced with the new, using the flat blade to help tuck the seal in as needed. I also had to use a hair dryer to soften the ... Read more new seal at some places in order to form it properly. Overall, I had great success!

tested bulb good ,replaced door switch first(least expensive)then ordered light socket and circuitboard.If clicking sound is heard replace circuitboard first to save on return shipping because the switch and socket where ok

Pop loose the plastic grate at the bottom.

Locate and remove the wheel leveling screw from the front bottom corner.

Remove cotter pin from the pin that mounts the wheel assembly to the refrigerator. Tap out the mounting pin.

Lift out the wheel assembly.

Remove the Roller pin from the wheel asse ... Read more mbly. I used a Dremel tool with a cutting disk. A hack saw will also probably work.

Install the new roller pin and wheel into the wheel assembly. Use a hammer or vice to peen over the end of the roller pin.

Reinstall and adjust wheel assembly.

I removed everything from the door, and unscrewed all of the nuts. I left the door on the refrigerator, mainly because I didn't think I needed to remove it. The gasket can be put on with the door attached, but I can see where it would be easier to take the whole door off. It would be easier to position the gasket laying down. All in a ... Read more ll, the repair went fine and the door seals much better.

Just replaced the switch, but unfortunately that was not the problem; nor was it the bulb....so I am back to square one.
But Parts Select is a great place to order from. Thank you.

1. I removed all screws holding the old gasket.

2. I removed the old gasket.

3. I removed and unfolded the new gasket from the shipping package.

4. I used a hair dryer to heat and straighten the gasket.

5. I installed the new gasket and secured it with the screws.

6. Some gasket defor ... Read more mation still remained, so I used the hair dryer again the next day to heat the gasket. Adding a small piece of cardboard behind
the gasket also helped to restore the gasket shape.

Inserted the glass shelf into position - very easy. Replaced the broken door handle. Note - the screws that held the handle in place and a plastic insert that covered the screws were not included with the repair parts. Fortunately, I had kept the old ones. Otherwise, the repair was very easy.