TPX24PBBABB General Electric Refrigerator - Instructions

Use small putty knife to cut internal sealant on ice maker door trim piece. Then you can easily remove it.

Followed the online video. Unplugged refrigerator, removed trim piece, lifted control board cover, removed 4 screws retaining circuit control board and removed the 3 connectors from the control board. Located flapper and removed by using small flat tip to take tension off flapper connectors. Helper held flash light to illuminate flappe ... Read more r connectors. Reversed procedure. New flapper seals well and cured problems. Circuit board was a bit different than one in video, but still had the 3 connectors. Marked each connector with grease pencil at top edge to ensure correct reconnection. Should note how wires are threaded around circuit board to ensure they are tucked back in correctly in reassembly. Remove trim piece carefully. I broke 2 of the 8 plastic pins that hold trim on. May be due to age of unit as they were brittle. 6 pins still hold trim piece flush.

Turned water supply off; pressed dispenser sw to release presure ; cut tubing holding reservoir ; nuit driver to release screw holding reservoir and pulled out ; took outside and used hose nozzle to try to clear; did not clear at first then took weedeater string and disloged something and water flowed freely; turned out had to change waer ... Read more solenoid valve (both) as the one for the water dispener was also plugged which did not show up before.
P.S. Had back flow water thru system before and changes of parts. Water flowed freely.

Separately (from a different site) purchased new compressor fan and motor. I purchased the grommets here because the other site listed the grommets as temporarily out of stock. I did watch one of the videos on PartSelect about the grommet replacement. Repair was pretty simple, biggest challenge was getting to the screw on the far side o ... Read more f the motor. Removed the two screws holding the fan motor into place. Removed motor and blade. Reinstalled with new fan blade, new grommet and new motor.

I removed the plate covering the water valve for the ice maker and water dispenser, removed the nut holding the 5/16" tubing to the valve and took off the tubing and nut. I did not need to turn off the water supply or unplug the unit. I removed the kick panel in the bottom front of the refrigerator, replaced the existing plastic fitting w ... Read more ith a new push-on fitting, then spliced the tubing coming from the water chiller to the valve where the leak was thus bypassing the broken tubing with new tubing. I reassembled the valve using the original plastic compression nut, replaced the cover and ran the water dispenser while checking for leaks. The water dispanser works great with no leaks.

Take a thin flathead screwdriver (or metal spatula) to separate the lower molded strip from the handle. Once removed, I discovered two small screws that secure the bottom of the main handle were loose. The head of the screws had five points which required a special drill bit that I had in my tool box. The screws were tightened allowing ... Read more me to align the replacement Tail strip and snap it in place. Some pressure is needed to secure it to the door. Once you hear the inserts "snap", then check for any open spaces between the strip sides and the door. If none, you're done!

Replaced flapper. Followed the video. The lamp caused the removable plastic bracket (which supports the control panel and the ice chute) to fuse with the plastic frame in the door. Eventually broke the fused plastic, removed the bracket, and filed the rough broken plastic before reassembly.

Part attaches to metal plate near crushing fingers which attaches to ice holding bin. Remove about 6 screws total on each side of plate. You must disassemble the auger & other parts so you can reassemble it in the proper order. Not many parts but i always take pics to cut down on time. New part is at the other end of the auger and acts a ... Read more s the holde of the auger shaft. Picture a crankshaft with a bearing on each end so the auger rotates between new part and the other end of auger shaft. That's it.

Part was perfect fit .Removed fan .three screws.replaced that s it

Opened, discovered not flapper but more complicated

I didn’t do the repair because I ordered two grommets. When they arrived, one of the packages was empty! Instead of just sending me another one, they refunded the part so I still need one. By the way, I was not refunded half the shipping either which was more than the part itself.

The video to replace the flapper looks easy, howerer the first step is to remove thestic cover of the icemaker. In my refrigerator model (as oposed to teh one shown n teh video) teh coved if firmly attached and goes under the refrigerator external plate so I was never abel to take it oot (so step 1 failed).
I was able to replace the ... Read more flapper TROUGH the whole whre te ice comes from! this took lots of patients and someone with small hands!

Cut the line inside the regiferator behind the bin and used the tube union to attach new 5/16" tubing to run to the solenoid valve assy in the back of the refigerator. Location of the valve assy makes connecting very difficult. But was able to complete repairs.

1. Use skewer to press plastic tabs under control panel, 2. Remove control panel and unplug solenoid, 3. Unscrew dispenser assembly and solenoid screws, 4. Press in tabs on lamp and remove assembly - unplug, 5. Replace lamp assembly, 6. Replace solenoid assembly and fasten scr ... Read more ews, 7. Replace flapper. 8. Replace other parts in reverse order.

son did the work BUT ONLY AFTER- trying to order the part from Sears parts online, in which they never from the right part and i spent 1 and 1/2 hours on chat and finally gave up. THEN i called sears replair, made appointment for two weeks later requesting 1st repair time of the day, was asured the repair would take place between 8-12 an ... Read more d beacuse it was 2 weeks away it should be the 1st repair. The day of the appt I received a phone call at 11:38 saying they would be here about 12:20, I SAID NO THANK YOU< OUR AGREEMENT WAS BY 12:00. THen I got online typrd in water tank your company come up, showed photo, and price which i ordered it can in my son fixed it and all was complete within an hr.