TPH21PRSAWW General Electric Refrigerator - Instructions

After inspection of the new door recess assembly, I realized that I could use sidecutters (electronic assembly type) and 'clip' off the inward lock tabs of the old recess assembly and disengage it from the crank door arm without any further disassembly of the refrigerator door. It was easy to 'unhitch' the tang from the crank arm and wi ... Read more ggle it out through the external opening of the ice/water dispenser compartment. I reversed the process and inserted the new assembly through the external opening of the compartment. The new door recess assembly snapped into place on the crank arm and fit tightly against the ice chute opening, correcting the issue caused by aging distortion of the old rubber seal cup portion of the door recess assembly.

Ordered at PartSelect and received the auger and blade within days. Printed the parts diagram and proceeded to take the auger apart the time it took would have been much less but I seized the opportunity to do a deep cleaning of the old parts before replacing them....The part diagram was the key to simplicity and the fast shipping was aw ... Read more esome. Thanks I'll be back....

The only difficult part was not knowing which parts had to be removed to gain access to the flapper to replace it. It appeared as if the frame around the control panel would have to be removed as well as the door handle; we tried but were not able to remove the frame. It turned out that the panel just popped out with the frame in place. O ... Read more nce we had access to the flapper, it was easy to replace it. The repair fixed the problem.

Let me start by saying, I usually hire something like this out but figured I would give it a try. The install was fairly straight forward, however it would’ve been nice if the instructions would have been more useful. Instructing me to remove one screw to release the auger and solenoid enclosure wouldve been nice. There were 3 other screw ... Read more s that I didn’t need to remove and they were the ones holding the auger in place, which made assembling that much more difficult. Once to enclosure was removed, and the solenoid was exposed, it was a seemless process. I would however, recommend paying attention to or taking a picture of the connections on the solenoid. I was lucky to remember or got lucky. Regardless, I was able to complete the project successfully. If I had to do it again, I believe it can be done in 30 minutes or less.

Removed old ice bucket with auger. Unscrewed front plates that form the front of the ice bucket. Replaced the front plates on the new part (ice bucket and auger). Replaced new assemblage. It took about 20 minutes. Had to empty ice out and put in a temporary cooler for storage. Bigger problem than the repair was diagnosing what was wrong ... Read more . Pushed disagnose button and it said ice maker was working normallly. Careful examination of the ice bucket removed from refrigerator showed spring out of place on long metal rod that protrudes from the back of the ice bucket and fits into a square hole in back of refrigerator. Examined other end of rod that engages with plastic parts that run the ice auger and ice crusher mechanism. A piece must have broken off. That was the problem. Refrigerator ice maker now works fine as originally designed. Push crudh the ice crusher engages and you get crused ice. Push cubes and the icemaker crusher slides out of the way and you get cubes.

This is the easiest thing in the world - thanks for sharing other's installation - it took 5 mins - works perfect & we have clean ice - 4 easy screws to remove - anyone can do it!

i ordered this ice maker on sunday night and paid for the cheapest shipping. it got here monday morning and i couldnt believe it. super fast shipping!! works great

Replaced flapper valve per website instructions. GE factory technician took two weeks to get here, charged over $100 for the call and told us we needed a new refrigerator door at a cost of over $500 to fix the problem. We sent him packing. After visiting the PartSelect website, the $5.88 PartSelect flapper valve fixed the problem. Ama ... Read more zing.

Screwed new bulb in socket

Use small putty knife to cut internal sealant on ice maker door trim piece. Then you can easily remove it.

Followed the online video. Unplugged refrigerator, removed trim piece, lifted control board cover, removed 4 screws retaining circuit control board and removed the 3 connectors from the control board. Located flapper and removed by using small flat tip to take tension off flapper connectors. Helper held flash light to illuminate flappe ... Read more r connectors. Reversed procedure. New flapper seals well and cured problems. Circuit board was a bit different than one in video, but still had the 3 connectors. Marked each connector with grease pencil at top edge to ensure correct reconnection. Should note how wires are threaded around circuit board to ensure they are tucked back in correctly in reassembly. Remove trim piece carefully. I broke 2 of the 8 plastic pins that hold trim on. May be due to age of unit as they were brittle. 6 pins still hold trim piece flush.

Remove front cover did not remove wires remove ice and water unit took off flapper put new one on 5 minutes back together

Replaced dispenser door flapper by following the do it yourself video in this site. It was really easy. Just be careful when removing the dispenser black bezel. I broke one of the little tabs when taking it off.

0. As a safety precaution, unplug the range or hit the relevant fuse breaker before you start. You might also want to grab a flashlight. Definitely do not try to do this while the oven is hot.
1. Pinch the wire over the light bulb cap to remove it. This is inside the oven at the back.
2. Pop off the hemispherical glass cap.
... Read more />3. Unscrew the old light bulb, and screw the new light bulb in its place.
4. Put the cap back.
5. Secure the cap by putting the wire back in its slots on the cap.

No tools needed, the cap is just held in place with pressure from the wire.

I just followed the instructions on the video and it was exactly as they said......no surprises.