TMH14XMS2 Estate Microwave - Instructions

First, we had to clean up all the interior surfaces, which was just cleaning. There was no internal damage. Then, just setting the center connector, rotary rollers and glass plate. Simple

Removed bed two screw replace grill

Whirlpool Model# MH1150XMS-0 purchased in 2004. I called Whirlpool and they suggested a new microwave. No big surprise - being the thrifty person that I am I wasn’t taking this for an answer. I figured if I had to purchase a new microwave what was $35.22 (part# PS373828 + shipping) if it worked.

I replaced the latch on th ... Read more e microwave door. Once the latch was replaced. I also took this time to make sure that the microwave door was in alignment. Thereafter, I had to adjust the door interlock switch behind the microwave console panel to recognize the microwave being closed. Yes, gaining access to all these areas was a bit difficult but have patience. TADA!!!....microwave is working. #girlsrock

We took a chance on the less expensive black Whirlpool vent grille as I found online that it would fit our stainless steel Kitchenaid microwave. My husband was able to pry the stainless cover off the broken grille and snap it onto the new black one. Then just screw in the top screws to secure. We are very happy with the stainless/black ... Read more of the new setup. It goes very well with the stainless/black of the cooktop and oven.

After taking the three screws out of the side of the door, I actually had to get help from my Dad who came over and was able to pry the top corner of the door out of the casing. I was afraid I was going to break the door. Once he got the door pried apart, I was able to replace the handle, clean the entire door and quickly snap it back i ... Read more nto place and then replaced the screws.

removed perimeter screws from the bottom side and the lower cover is hinged at the wall side. Motor is visible and easily removed with two screws. Take of the old one, install the new one, and reverse the procedure to put the bottom cover back in place. Will nee helper to hold one side of the bottom until couple of screws can be put in on ... Read more the other side.

Unscrewed glass panel, removed old bulb, cleaned glass panel and installed new bulb. Screwed panel back into place.

Ordered a new motor. Removed the outside trim of the oven-microwave combo. 2 screws at the bottom of the trim. Removed the screws that held the combination micro and oven unit in place. Removed the top and bottom black plastic grill of the microwave. 3 screws each. Pulled the entire unit out about 1 inch exposing the screws at each ... Read more side of the microwave that hold it in place.
Snapped off the top control panel which exposed the wiring connecting the control panel.
Unplugged a couple of wire harness units to free the control panel.
Be sure to label the units to know which goes where during reassembly.
Remove the microwave unit from the housing and place it on its side.
Remove the metal plate that houses the motor. 4 screws hold the motor in place. Disconnect the 2 wires from the old motor and you are ready to install the new motor. Be sure to TURN OFF THE POWER to the unit at the breaker box and remove the turntable from inside the microwave.

Ordered the glass tray and installed it. Received the orderin about two days.

The most difficult part was getting the old screw out of the top of the grille. Once that was accomplished, the rest was easy as can be. I would highly recommend your service - very good! Thank you!

Removed retaining screws and broken parts; inserted new grill and screws. Fin!

removed old vent and replaced by snapping in and two screws inserted into right and left top connections.

Took out the turntable parts to ensure I ordered the correct cooking tray. Matching those with photos of related parts on PartSelect worked great. Put turntable drive and support ring in place and cooking tray went in very easily. Plan to order a second one to have on hand for this rental property.

Placed to new grille on the microwave and attached
with the screws.

The part came very quick less than a week. The installation took less than 15 minutes.