EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

TGS326VD0 Estate Range - Instructions

All Instructions for the TGS326VD0
91 - 105 of 149

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Oven gets too hot,if set at 350 it heats to 550. Changed the sensor and was not the problem.
0 of 2 people found this instruction helpful.
  • Joanne from Negaunee, MI
  • Really Easy
  • Less than 15 mins
  • Screw drivers
Took off the screws on the back of the stove and took out the sensor, and put in the new one.
Was this helpful?
Thank you for voting!
Bulb Replacement
0 of 2 people found this instruction helpful.
  • Judith from Phoenix, AZ
  • Really Easy
  • Less than 15 mins
I pulled down the wire around the glass cover. . . Released on end of the wire from its holder being careful to not let the glass cover drop. Unscrewed the bulb and replaced with replacement. Easy, easy.
Was this helpful?
Thank you for voting!
Both outside door handles turned very beige
23 of 76 people found this instruction helpful.
  • Howard from Boynton Beach, FL
  • Easy
  • 30 - 60 mins
  • Nutdriver
Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discol oring refer handles. Thank you
Was this helpful?
Thank you for voting!
Damaged Socket When Removing Bulb Base
  • Charles from Oceanside, CA
  • A Bit Difficult
  • 30 - 60 mins
  • Pliers, Screw drivers
This is a built-in oven, so the biggest problem was figuring out how to remove it from the cabinet. The solution turned out to be removing the cooktop above it and unscrewing two screws that connected the oven to the inside of the cabinet. The other problem was removing BOTH metal backs from the oven. The first one was easy. The secon d one wasn't. The old socket was recessed behind the second back, making it virtually impossible to access the metal "wings" that hold it in place, so I ended up pulling out the socket assembly from inside the oven with pliers.
Was this helpful?
Thank you for voting!
Valve stem broke at the knob
  • Randall from Corona, CA
  • Easy
  • 30 - 60 mins
  • Screw drivers, Wrench set
Lifted the top disconnected the old valve and replaced with a new one.I believe the valve should have been shipped with two gaskets,. One for the bottom and another for the top. I reused the old one on the top with no problem but would have preferred a new one.
Was this helpful?
Thank you for voting!
Ignater would ignate the first time, but then after the oven went off the ignater would not re-ignate and the ove would rmain off
  • Jose from Woodbridge, VA
  • Easy
  • 30 - 60 mins
  • Screw drivers, Socket set, Wrench (Adjustable)
The first thing you need to do is remove the racks from your oven.

Then look around at the back of your oven for the screws that hold the bottom pan down.

Remove those screws and remove the pan. Some need to slide back and then come up others will just pull up.

Remove the heat shield that is over the burn er.

Remove the bottom drawer of your oven.

Now you should be able to see the igniter that sits on an angle by the burner tubes with a couple of wires coming out of it.

Removing the screws that hold the igniter is probably the most difficult part with some ovens. Sometimes it is easier to remove the whole bracket that holds the igniter and then remove and replace the igniter out of the oven.

The wires for the igniter will go to a Molex plug. Follow the wires and undo the plug. On many units it will be below the oven in the drawer opening at the top back. You will need to lay flat on the floor and reach back in to do this.

Once you have the old igniter out then you can carefully install the new one.

Check to make sure that you can feed the Molex plug and wires down through to the bottom before fastening the igniter.

Once the igniter is secured and the plug is connected, you can then replace the other parts in the reverse order that they came out.
Was this helpful?
Thank you for voting!
the bottom hinge pin fell out and door was loose
  • Peggy from Ogden, UT
  • A Bit Difficult
  • 1- 2 hours
  • Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
Ordered parts that I thought were correct. BUT I ordered from the door parts... which gave me the wrong screw and unnecessary shims. What I really needed was the cabinet parts! At the time of doing the order, I could not find the owner manual... but found it before the parts arrived. That is what saved me and also thanks to me, for b eing a pack rat and my grandson finding the spacer on floor after it came out. That made it possible to fix the door. The screw I tried to install, but soon realized it was wrong. I went thru the pack rat stash and found the screw that fell out late last year.....! I then noticed the screw holding the hinge bracket was loose, now that is almost impossible to tighten because everything or tools that I owned were tooooo long (it's only 1 1/2" off the floor)! I tightened that and put the spacer and bottom hinge pin in. The screw was only 3/4" off the floor and difficult to get into the hole without a mirror on the floor under the spot. I finally used a clamp wrench to hold the screw and thread the screw into the hole. From there, most sockets are too long, so I did find a short socket. Now that still took me to the mirror, so I used the clamp wrench to hold the socket to tighten the screw. Thank goodness I am mechanically inclined and can look at a schematic to to understand how something works or I would have had to call for a mechanic. Also I should say ... FIND you manual before ordering to start with the right parts! Manual showed the parts of the cabinet and the door as one long picture, which helped with the repair and would have for ordering.
Was this helpful?
Thank you for voting!
oven not maintaining temperature
  • John from East Elmhurst, NY
  • Easy
  • 30 - 60 mins
  • Nutdriver, Socket set
Replaced bake igniter only as recommended by others, no need to buy the whole unit. The bottom screw is difficult to access, use a 1/4 inch socket set with 8 mm socket. Advice to remove bottom storage drawer to make sure wire is connected to the igniter. So far it works fine.
Was this helpful?
Thank you for voting!
oven wouldnt stay lit
  • jasper from pekin, IL
  • Easy
  • 30 - 60 mins
  • Screw drivers
all I did was replace the igniter and that fixed my problem simple to do.
Was this helpful?
Thank you for voting!
Often would not heat. Burners on syove were O.K.
  • Bruce from Michigan City, IN
  • Easy
  • 1- 2 hours
  • Screw drivers
Removed door per instructions in manual. Removed racks and storage drawer per manual. Removed two phillips head screws holding bottom pan and removed pan. Removed two phillips head screws holding igniter tube (#12) and withdrew tube from the cavity. Removed two phillips head screws holding igniter and bracket to the tube. Unplugged elcetr ical connection to igniter and installed new igniter in reverse order. Too bad the igniter wasn't the problem.
Was this helpful?
Thank you for voting!
broken knob
  • Steve from Katy, TX
  • Really Easy
  • Less than 15 mins
had to replace a broken knob, plastic was broken on the inside fitting. Took all of 2 seconds to replace
Was this helpful?
Thank you for voting!
Igniter went out
  • carl from peoria, IL
  • Really Easy
  • Less than 15 mins
  • Screw drivers
Pulled shelves out removed bottom plate of oven remove heat shield cover removed screws had to remove bottom drawer disconnect wire from bottom of igniter and remove from top side . Replaced by reversing steps.
Was this helpful?
Thank you for voting!
Oven has not heat
  • Gregory from Arlington, VA
  • Really Easy
  • Less than 15 mins
  • Screw drivers
Open oven door and remove racks. Remove 2 screws at back of oven floor and remove bottom plate. Unscrew screws that hold flame defuser. Remove defuser. Remove screws that hold bake igniter and flame tube. Unplug wire to bake igniter. Remove screws to bake igniter. Replace old igniter with new igniter. Replace screws and wire to ig niter. Replace flame defuser and put screws back. Put bottom plate back into oven. Replace 2 screws at back. Replace racks. close door and test by setting thermostat to some temperature and verify that oven works.
Was this helpful?
Thank you for voting!
Missing control knbs on stove.
  • Dawn from Anthem, AZ
  • Really Easy
  • Less than 15 mins
This could not have been any easier. The site walked me through selecting the correct part and it arrived quickly. When I got the part, it slid right on.
Was this helpful?
Thank you for voting!
broken knob
  • gerard from camarillo, CA
  • Really Easy
  • Less than 15 mins
Just push knob into place.
Was this helpful?
Thank you for voting!
All Instructions for the TGS326VD0
91 - 105 of 149