TGS326MS2 Estate Range - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
broken knob
-
gerard from camarillo, CA
- Really Easy
- Less than 15 mins
Just push knob into place.
Was this helpful?
Thank you for voting!
broken knob
-
Steve from Katy, TX
- Really Easy
- Less than 15 mins
had to replace a broken knob, plastic was broken on the inside fitting. Took all of 2 seconds to replace
Was this helpful?
Thank you for voting!
Igniter went out
-
carl from peoria, IL
- Really Easy
- Less than 15 mins
-
Screw drivers
Pulled shelves out removed bottom plate of oven remove heat shield cover removed screws had to remove bottom drawer disconnect wire from bottom of igniter and remove from top side . Replaced by reversing steps.
Was this helpful?
Thank you for voting!
Oven Control Knob Broken
-
Gordon from Yukon, OK
- Really Easy
- Less than 15 mins
Remove old knob and put new knob in. About 10 minutes total.
Was this helpful?
Thank you for voting!
broken handle on drawer on range
-
Charles from Marshall, MI
- Really Easy
- Less than 15 mins
-
Screw drivers
The repair was VERY simple....2 screws, remove the broken handle, put now one in place, put back the 2 screws... done!! What I want other to know... is who with about 6 clicks from my home pc, I had the exact part i needed, ordered!!! I was dreading ordering this part so much because of all the hassle I have in getting to a website to ord
... Read more
er, and all the crap that goes with finding, the part....the ordering the part. This site was SOOOOO cool!! The handle had been broke for almost a year, and didn't want to replace it because of the usual hassle that goes with 'The Hunt". If I had know that Parts Select was so good about this, I would have had the new one installed 3 days after the original handle broke!! And shipping was SO FAST!! Have you people in my book marks for sure!! Thank you one and all!!!
Read less
Was this helpful?
Thank you for voting!
Oven light not on.
-
Kasey from Morrisville, NC
- Easy
- Less than 15 mins
-
Pliers, Screw drivers
Turn off the breaker to the range. Unplug, too. Took off the 8 screws that hold the upper back panel on. Took a picture of the wire setup (this ain't my first rodeo). Removed two screws on the bottom of the old latch that hold it in place. Carefully removed the wire leads with needle-nose pliers because I didn't want to replace the wi
... Read more
re leads. Reconnected the wires to the new latch, replaced the two screws to hold it onto the oven. Tested with the rocker switch on top and the oven door, both worked. Put the back panel on with the 8 screws.
Read less
Was this helpful?
Thank you for voting!
draw pull handle broke
-
Mark from Lawton, OK
- Really Easy
- 15 - 30 mins
-
Screw drivers
Took off the old handle ,cleaned the surface then peeled off the double sided tape and replaced the new handle.
Was this helpful?
Thank you for voting!
Oven did not rise to temperature when at the bakie setting
-
Brett from Arlington, WA
- Easy
- 15 - 30 mins
-
Screw drivers, Wrench (Adjustable), Wrench set
First make sure it is the gas valve not the ignitor. If the clicking sound still happens then the ignitor is fine, no clicking means ignitor may be broke and try to fix that first because it is cheaper. For us I knew it was the valve because the ignitor still clicked and the broil and top elements still worked. After the part arrived I tu
... Read more
rned off the gas and pulled the power to the oven. Disassembled all the components taking pictures along the way to remember what it looked like to go back together. Installed the new valve and use yellow gas tephlon tape at the seals. Put components back in reverse order. Run the top elements first to get gas in all the gas lines and remove the air. At this point the oven bakes again.
Read less
Was this helpful?
Thank you for voting!
oven temperature did not stay as set
-
Paul from Cornelius, NC
- A Bit Difficult
- 15 - 30 mins
-
Screw drivers
changing the part itself was easy, but the sheet metal covering the whole back of the oven was difficult to remove because of some screws that were stripped. The new sensor solved the problem.
Was this helpful?
Thank you for voting!
oven would not light (heat up)
-
william from parkville, MD
- Really Easy
- 15 - 30 mins
-
Screw drivers, Socket set
oven would not light but broiler and range top would. removed oven racks. removed 2 finger tight screws on oven pan floor and pulled up oven floor. also removed storage drawer under oven- also 2 screws. now your oven should look like the inside of your gas grill. removed 2 more screws on burner plate and removed plate. unplugged ignite
... Read more
r and 2 screws holding igniter. replaced igniter and put together in reverse order. oven now works perfectly
Read less
Was this helpful?
Thank you for voting!
Light bulb failure
-
Grant from Alexandria, VA
- Really Easy
- Less than 15 mins
Received the part the day after ordering. Appreciated the quick service and repair took less than a minute.
Was this helpful?
Thank you for voting!
Broken oven handle
-
CONSTANCE from LAWTON, OK
- Really Easy
- Less than 15 mins
-
Screw drivers
I removed the handle from the door, replaced the old one with the new one............. 1, 2, 3, just that easy. The replacement part arrived very quickly and the price could not be beat. Would I use them again...........Yes!
Was this helpful?
Thank you for voting!
Broken drawer handle
-
Nick from Chapel Hill, NC
- Really Easy
- Less than 15 mins
-
Screw drivers
My son broke the drawer handle of our stove a few years ago. It took me a while to get this repaired because the first company we ordered from shipped the wrong product to us and did not allow us to do a return! The team at PartSelect had the correct product delivered in just a few days! Once I had the product on hand the repair was su
... Read more
per easy. Thanks PartSelect for great service!! Nick, ShirtsThatGo
Read less
Was this helpful?
Thank you for voting!
Scews from old one didn't fit the new one.
-
Raymond from Ashland, WI
- A Bit Difficult
- Less than 15 mins
-
Screw drivers
I had to bring the new handle to the Hardware store and have them pick out screws that would work. The only problem is that I live 12 miles one way from the Hardware store. My advise is to order scews when ordering the handle.
Was this helpful?
Thank you for voting!
Bake would not work all the time
-
Philip from New York, NY
- Easy
- Less than 15 mins
-
Nutdriver, Screw drivers
The bake part of the oven was not igniting all the time . I checked the website and they don't list the igniter separately from the burner tube. This part is the exact fit for the igniter. There is no need to buy the whole kit if the igniter is all you need. it will fit right on the burner tube with no modification at all. Part number PS8
... Read more
97264 is the igniter and burner tube. Part number PS898618 is just the ignitor.
Read less
Was this helpful?
Thank you for voting!