EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

TGS326MS2 Estate Range - Instructions

All Instructions for the TGS326MS2
61 - 75 of 169

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
oven would not completely heat up, only heating to about 150 degrees Temp.
2 of 2 people found this instruction helpful.
  • Isaac from MATTESON, IL
  • Very Easy
  • 15 - 30 mins
  • Screw drivers
contracted a repair service person
Was this helpful?
Thank you for voting!
Corroded/greasy bottom oven tray
2 of 2 people found this instruction helpful.
  • Robert Ruth from FERNDALE, WA
  • Very Easy
  • 15 - 30 mins
  • Screw drivers
Loosened two screws and removed tray, very simple. Replaced new tray and adjusted screws to hold tray. Easiest part was finding new tray part number and ordering replacement using online parts diagram.
Was this helpful?
Thank you for voting!
Oven not reaching temperature
2 of 2 people found this instruction helpful.
  • Marsha from Clermont, FL
  • Really Easy
  • Less than 15 mins
  • Screw drivers
Simple-pulled range away from wall, unplug from socket. Removed back panel unscrewed thermoses and replace. Put back panel back on plug in, tested temperature setting before sliding range back on place
Was this helpful?
Thank you for voting!
Replacing the bulb in the freezer side
5 of 11 people found this instruction helpful.
  • Yafa (and David) from Bothell, WA
  • Easy
  • Less than 15 mins
  • Nutdriver
Removed the ice brucket,
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.

Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.
Was this helpful?
Thank you for voting!
Broken handle
3 of 5 people found this instruction helpful.
  • Derek from Middleport, NY
  • Really Easy
  • Less than 15 mins
  • Screw drivers
Simple removed two screws pulled old one off installed new.
Was this helpful?
Thank you for voting!
Stove would not light due to faulty electronic ignighter
2 of 2 people found this instruction helpful.
  • Victor from SAINT PETERS, MO
  • Really Easy
  • 30 - 60 mins
Very easy repair, simply remove old ignighter and install new one. Take pictures if you need help remembering where everything goes.
Was this helpful?
Thank you for voting!
oven handle broke
2 of 2 people found this instruction helpful.
  • Jim from CAMDENTON, MO
  • A Bit Difficult
  • 30 - 60 mins
  • Screw drivers
new handle arrived black for white oven - screws did NOT fit new handle- glass came off the door when removing old handle
Was this helpful?
Thank you for voting!
Draw handle broke. Slides worn out
2 of 2 people found this instruction helpful.
  • Richard from EAST LYME, CT
  • Easy
  • 30 - 60 mins
  • Pliers, Screw drivers
Replaced handle and slides. Drill third hole in handle add one more screws.
Was this helpful?
Thank you for voting!
Oven would not maintain Heating
2 of 2 people found this instruction helpful.
  • Cheryl from WEST JORDAN, UT
  • A Bit Difficult
  • 30 - 60 mins
  • Screw drivers, Wrench (Adjustable)
Following details from the installation video, after removing the main gas line and the two output lines I removed the four screws that removed the valve but found it was easier to remove and install the new one if I first removed the oven burner(it made for lining up the valve nozzle to the burner easier) from the inside, 3 wires attach on the side towards the stove taking one wire from the old valve and putting it on the new valve in the same place. Everything went back together just fine, I did have some problem with tightening one of the two gas lines for the output and found I just had to keep tightening it a little until there were no bubbles appearing when I applied soapy water to the connections, other than that it was very straight forward.
Was this helpful?
Thank you for voting!
Didn’t work
2 of 3 people found this instruction helpful.
  • James E. from WAYNE, MI
  • Really Easy
  • 30 - 60 mins
  • Screw drivers
Took out old one but electric hook up fell in the hole had to fish it out also dropped a screw in the hole could’ve find it used a different one
Was this helpful?
Thank you for voting!
I was trying to remove the oven door so I could clean the glass. Spills had run down between the layers of glass.
3 of 6 people found this instruction helpful.
  • Karen from Oklahoma City, OK
  • Difficult
  • More than 2 hours
  • Screw drivers
This oven probably was manufactured in the '60s when the house was built. The door doesn't just pull off like the newer models. These pins fit into small holes on the oven hinges. I inserted the pins and lifted the door to a 45 degree angle, before pulling the door completely off. Now that turned out to be the easy part. I then proce eded to completely dismantle the door. It actually has 4 glass layers which had to be cleaned individually. The hardest part of all was actually remembering how to put it back together again. I put the door back on just as I had removed it, then took out the pins, and I was finally done! This was not an easy project, BUT the results look great.
Was this helpful?
Thank you for voting!
last oven bottom was ruined by melted and burnt plastic
2 of 3 people found this instruction helpful.
  • Dennis from Missouri Valley, IA
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
took out old oven bottom by removing 2 screws, placed the new oven bottom in place put the screws back in and was done.
Was this helpful?
Thank you for voting!
LIght switch on oven door was broken
2 of 3 people found this instruction helpful.
  • James from Sequim, WA
  • Easy
  • Less than 15 mins
  • Screw drivers
Turned off power at circuit breaker. Removed 4 phillips screws from area over oven door. Pulled control panel out and twisted to clear top rail. Pulled two wires off of old switch.Pulled old switch through panel. Inserted new switch. Attached the two wires to new switch. Replaced panel and inserted four screws. Turned on power - it works!
Was this helpful?
Thank you for voting!
temp level uneven
2 of 3 people found this instruction helpful.
  • Paul from HARMONY, MN
  • Very Easy
  • 15 - 30 mins
after watching the video, installed the temp sensor. Super easy
Was this helpful?
Thank you for voting!
the oven temperature was not working right. I installed a new oven sensor. Works get now
3 of 6 people found this instruction helpful.
  • Rosalind from APOLLO, PA
  • Very Easy
  • 15 - 30 mins
  • Screw drivers
Watch the video...
Was this helpful?
Thank you for voting!
All Instructions for the TGS326MS2
61 - 75 of 169