EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

TGS325VT2 Estate Range - Instructions

All Instructions for the TGS325VT2
121 - 135 of 178

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Side trim broke
  • Paul from Adamsville, TN
  • Easy
  • 15 - 30 mins
  • Screw drivers
take the 2 screws that hold the handle on out...watch the glass front and the side trims because the handle holds them on. Take the glass out then remove the side trims. Replace the side trims holding the glass in place with 2 pieces of masking tape om each side then install the handle with the 2 screws and remove the masking tape.
Was this helpful?
Thank you for voting!
Could not get self cleaning oven to engage
  • Charles from Fairfield Bay, AR
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
Removed back of stove, 8 screws, removed original latch assembly and installed new assembly. One thing that can cause you difficulty is that the rod that connects the assembly to the front latch on the door can disconnect and has to be reconnected.[Problem]
Was this helpful?
Thank you for voting!
Gas range would not go into self cleaning mode. When pushing the self clean button, would get three beeps!
  • Lee from Saint James, NY
  • Easy
  • 15 - 30 mins
  • Pliers, Screw drivers
The malfunction was narrowed down to the oven door motor lock, located at the upper left back of the unit. Removed two panels from the back of the unit, 8 screws. Then the motor, 2 screws, 4 wire connectors. Reversed the procedure for the installation, and solved the problem. About 30=35 minutes for the job. If your handy at all, it should not be a problem.
Was this helpful?
Thank you for voting!
E-2 F-3 codes..Oven inop w/trying to bake.Beeps @ start attempt.
  • Dave from Titusville, FL
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
Contrary to instructions(go thru front of oven) I had to pull out the range, remove two (2) screws from back chassis. At this point you pull out the connector, snap in new, reverse proceedure. Very simple. Hardest part is cleaning up debris generated by moving range.
Was this helpful?
Thank you for voting!
Ignater would ignate the first time, but then after the oven went off the ignater would not re-ignate and the ove would rmain off
  • Jose from Woodbridge, VA
  • Easy
  • 30 - 60 mins
  • Screw drivers, Socket set, Wrench (Adjustable)
The first thing you need to do is remove the racks from your oven.

Then look around at the back of your oven for the screws that hold the bottom pan down.

Remove those screws and remove the pan. Some need to slide back and then come up others will just pull up.

Remove the heat shield that is over the burn er.

Remove the bottom drawer of your oven.

Now you should be able to see the igniter that sits on an angle by the burner tubes with a couple of wires coming out of it.

Removing the screws that hold the igniter is probably the most difficult part with some ovens. Sometimes it is easier to remove the whole bracket that holds the igniter and then remove and replace the igniter out of the oven.

The wires for the igniter will go to a Molex plug. Follow the wires and undo the plug. On many units it will be below the oven in the drawer opening at the top back. You will need to lay flat on the floor and reach back in to do this.

Once you have the old igniter out then you can carefully install the new one.

Check to make sure that you can feed the Molex plug and wires down through to the bottom before fastening the igniter.

Once the igniter is secured and the plug is connected, you can then replace the other parts in the reverse order that they came out.
Was this helpful?
Thank you for voting!
The Parts Came With No Instructions And We Couldn't Find Directions On Line.
  • Kathleen from Livingston, MT
  • A Bit Difficult
  • 1- 2 hours
We took the door off and took it and the side panels to the local dealer and he put them on for us - for anyone needing to replace the side panels on the over, be aware they slide under the glass front -not over it like we tried to do. We thought, though, that we were going to have a buy a new stove but for a little over $70. 00 We got the parts, had them installed and saved over $800 on a new stove - well worth the effort.
Was this helpful?
Thank you for voting!
oven not maintaining temperature
  • John from East Elmhurst, NY
  • Easy
  • 30 - 60 mins
  • Nutdriver, Socket set
Replaced bake igniter only as recommended by others, no need to buy the whole unit. The bottom screw is difficult to access, use a 1/4 inch socket set with 8 mm socket. Advice to remove bottom storage drawer to make sure wire is connected to the igniter. So far it works fine.
Was this helpful?
Thank you for voting!
oven wouldnt stay lit
  • jasper from pekin, IL
  • Easy
  • 30 - 60 mins
  • Screw drivers
all I did was replace the igniter and that fixed my problem simple to do.
Was this helpful?
Thank you for voting!
broken knob
  • Steve from Katy, TX
  • Really Easy
  • Less than 15 mins
had to replace a broken knob, plastic was broken on the inside fitting. Took all of 2 seconds to replace
Was this helpful?
Thank you for voting!
burner grate burnt out
  • Derrick from Marlton, NJ
  • Really Easy
  • Less than 15 mins
Replaced grates
Was this helpful?
Thank you for voting!
Igniter went out
  • carl from peoria, IL
  • Really Easy
  • Less than 15 mins
  • Screw drivers
Pulled shelves out removed bottom plate of oven remove heat shield cover removed screws had to remove bottom drawer disconnect wire from bottom of igniter and remove from top side . Replaced by reversing steps.
Was this helpful?
Thank you for voting!
Oven Control Knob Broken
  • Gordon from Yukon, OK
  • Really Easy
  • Less than 15 mins
Remove old knob and put new knob in. About 10 minutes total.
Was this helpful?
Thank you for voting!
Knob on range was broken
  • Ann from Scotch Plains, NJ
  • Really Easy
  • Less than 15 mins
Just put it on, very easy
Was this helpful?
Thank you for voting!
Oven has not heat
  • Gregory from Arlington, VA
  • Really Easy
  • Less than 15 mins
  • Screw drivers
Open oven door and remove racks. Remove 2 screws at back of oven floor and remove bottom plate. Unscrew screws that hold flame defuser. Remove defuser. Remove screws that hold bake igniter and flame tube. Unplug wire to bake igniter. Remove screws to bake igniter. Replace old igniter with new igniter. Replace screws and wire to ig niter. Replace flame defuser and put screws back. Put bottom plate back into oven. Replace 2 screws at back. Replace racks. close door and test by setting thermostat to some temperature and verify that oven works.
Was this helpful?
Thank you for voting!
Missing control knbs on stove.
  • Dawn from Anthem, AZ
  • Really Easy
  • Less than 15 mins
This could not have been any easier. The site walked me through selecting the correct part and it arrived quickly. When I got the part, it slid right on.
Was this helpful?
Thank you for voting!
All Instructions for the TGS325VT2
121 - 135 of 178