My Orders
- Home
- TFX27PFXDBB
- Instructions
TFX27PFXDBB General Electric Refrigerator - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Frost buildup in freezer by the ice maker
1 person
found this instruction helpful.
-
Alex from Cary, NC
- Really Easy
- 15 - 30 mins
-
Screw drivers
Replaced dispenser door flapper by following the do it yourself video in this site. It was really easy. Just be careful when removing the dispenser black bezel. I broke one of the little tabs when taking it off.
Was this helpful?
Thank you for voting!
My ice container and Ice chute were freezing up and getting blocked, and my filtered water line was also freezing
1 person
found this instruction helpful.
-
Joe from BRICK, NJ
- Really Easy
- Less than 15 mins
-
Screw drivers
I just followed the instructions on the video and it was exactly as they said......no surprises.
Was this helpful?
Thank you for voting!
drawer facing cracked
3 of 7 people
found this instruction helpful.
-
Christine from Delray Beach, FL
- Really Easy
- Less than 15 mins
ordered drawer face - perfect part- snapped right in. done. order came within 10 days.
will order again if needed.
will order again if needed.
Was this helpful?
Thank you for voting!
Bulb burned out.
3 of 7 people
found this instruction helpful.
-
Jimmie from Surprise, AZ
- Really Easy
- Less than 15 mins
Screwed new bulb in socket
Was this helpful?
Thank you for voting!
The light bulb in my freezer door burned out.
1 person
found this instruction helpful.
-
Peter from HAZELHURST, WI
- Very Easy
- Less than 15 mins
Remove the burned out bulb and install the new light bulb.
Was this helpful?
Thank you for voting!
Freezer Light Shield Cracked at mid fastening point
1 person
found this instruction helpful.
-
George V. from PITTSBURGH, PA
- Very Easy
- Less than 15 mins
replaced the broken one with the new part
Was this helpful?
Thank you for voting!
Ice maker discharge was slow and jammed with ice and frost. The cause was a distorted flapper that did not seal properly, admitting warm air into the dispenser chamber.
1 of 2 people
found this instruction helpful.
-
Al from River Edge, NJ
- Really Easy
- Less than 15 mins
-
Screw drivers
Excellent video was available on the Parts Select website. It was simple. The selector panel pulled out by hand from the bottom. The subpanel was removed with the four screws. The flapper snapped out of the holder with two clips. The new one was inserted in reverse order.
Was this helpful?
Thank you for voting!
Ice Maker Clogging up from frost build-up
1 of 2 people
found this instruction helpful.
-
GARY from LIVONIA, MI
- Really Easy
- Less than 15 mins
-
Screw drivers
Turn off power
Remove operator faceplate by pullling out on outer lower corners
Disconnect wire connectors from circuit board
Remove four screws from dispenser and pull out dispenser assy
Replcae Door ASsembly
Put everything back in place
Power up
Job Done
Remove operator faceplate by pullling out on outer lower corners
Disconnect wire connectors from circuit board
Remove four screws from dispenser and pull out dispenser assy
Replcae Door ASsembly
Put everything back in place
Power up
Job Done
Was this helpful?
Thank you for voting!
Ice Building Up In The Ice Dispenser Chute
1 of 2 people
found this instruction helpful.
-
joselito from riverview, FL
- Really Easy
- Less than 15 mins
-
Screw drivers
Under the control panel there are three small holes. Insert ballpen or small flat screw driver on both outer holes to push a tab lock that holds the control panel in place. Then pull out control panel and three set of wires will be exposed and disconnect wire connectors (connectors have different sizes so you wont get confused in reconn
... Read more
ecting). Unscrew four screws on each corner that holds the ice dispenser assembly (a part where you push your glass against to dispense ice or water. The flapper is exposed and easy to replace.
Read less
Was this helpful?
Thank you for voting!
The shield light had burned the shield
1 of 2 people
found this instruction helpful.
-
George from Cun City Center, FL
- Really Easy
- Less than 15 mins
I hung the new shield on the two inside pegs that were already there.
Was this helpful?
Thank you for voting!
froze in freezer
1 of 2 people
found this instruction helpful.
-
Ken from Wesley Chapel, FL
- Really Easy
- Less than 15 mins
unclipped and replace with new part.
Was this helpful?
Thank you for voting!
Frost collected in the ice dispenser shute clogging it
1 of 2 people
found this instruction helpful.
-
George from HOSCHTON, GA
- Really Easy
- 15 - 30 mins
-
Screw drivers
Replace the flapper and this solved it. The video provided was excellent and allowed me to do this repair myself.
Was this helpful?
Thank you for voting!
Only crushed ice. No cubed.
1 of 2 people
found this instruction helpful.
-
JACOB from COLLEGEVILLE, PA
- Very Easy
- 15 - 30 mins
-
Nutdriver
Found a step by step video on YouTube made replacement very easy. Cubed ice is back. Time for a cocktail to celebrate!
Was this helpful?
Thank you for voting!
Broken plastic on ice hopper that helped stabilize the auger
1 of 2 people
found this instruction helpful.
-
Phil from MADISON, WI
- Very Easy
- 15 - 30 mins
-
Screw drivers
Emptied hopper
Removed screws to remove auger from existing
This was so easy I impressed my wife
Removed screws to remove auger from existing
This was so easy I impressed my wife
Was this helpful?
Thank you for voting!
rusty plate in the ice dispenser.
1 of 2 people
found this instruction helpful.
-
Roberto from Wildomar, CA
- A Bit Difficult
- 30 - 60 mins
-
Nutdriver, Screw drivers, Wrench (Adjustable)
removed the dispenser and disasembled it repaced plate and reasembled.
Was this helpful?
Thank you for voting!