TFX24PFXBAA General Electric Refrigerator - Instructions

Screwed new bulb in socket

Concerned about removing and attaching front panel to broken drawer. Rep. said wasn't sure but most just snapped together. Rep. was correct. No tools required.

Remove the burned out bulb and install the new light bulb.

replaced the broken one with the new part

I placed books under the door until I had enough to hold the door up about 1/2 inch higher then when it is closed. The books and the magnetic gasket will hold the door, JUST DON'T TRY TO OPEN IT TILL YOU'RE THROUGH. That's about how high the cams lift the door when opened. I removed the two screws holding the door stop. Then removed the ... Read more two screws holding the lower hinge pin.

It takes two of the cams

and the bottom one is riveted to the hinge. I used a grinder to grind the rivet so I could tap the pin out holding the cam. Put the new cam on and put the pin back in. I didn't put a new rivet, just gravity should hold it. I put the second cam on the hinge pin and one of the screws on the door stop holds it in place after you slide the hinge pin back into the door and replace the screws in the bracket then the door stop.
Make sure your lower door gasket didn't get damaged while the cams weren't working because the door wasn't being lifted up when opened.

Same problems as already described .... door would not close, plastic bits on floor, angry, ready to throw-out 15 year old “dog” and blow at least $1,000 on a new appliance!

This repair is dead easy. Remove the two bolts holding the top hinge and lift off the entire door. Don’t be surprised if the original Riser Cam has virt ... Read more ually disintegrated, mine was a wreck. Remove two bolts that retain the old flat metal “shim” and fiber “gasket”.

Fit new Riser Cam and re-use old shim and gasket. Replace door on dome-shape bottom hinge mount and then re-fit top hinge.

If in any doubt order new shim and gasket along with the new cam riser. Or, do as I did, and “manufacture” either of these parts from scrap material found in the workshop ....

Like the rest of the other statements it was easy with 2 2X4 pieces of wood to block the door up. The other suggestion about buying two of the pieces was a good idea. Once I took off both the top and bottom pieces they were both worn out and it was easy to replace them both at the same time. The door is working good again and shuts on ... Read more its own.

took top bracket off--then removed door--took
bottom bracket off bottom of door and replaced
door closing cam and reasembled---a piece of
cake

I blocked the door up with one 2X4 Then removed the lower hinge, installed the closing cam. Then I found that I needed one more closing cam that I didn't order the first time. This other one mounts to the lower section of the door and both cams set together. Re-ordered another cam. When it came in I installed it. Between ordering both ... Read more parts I had them both in three days. The best to Parts Select
I now know where to buy my parts if needed again.

Thanks
Bob
Sandusky, Ohio

Removed the top hinge cover held by one screw. Removed the top hinge held by two screws and them lifted the door up and off the bottom hinge. Laid the door on the floor and replaced the cam piece from the kit on the bottome of the door. That required removing one screw and losening another. Removed the lower hinge (two screws) and replace ... Read more d it with the new one in the kit. The lower hinge includes the other cam piece. Lifted the door onto the lower hinge and then replaced the top hinge and cover.

Removed four screws at bottom of door, while someone held the door in place replaced the upper cam (there are two) applied some silicone plumbers lube between the mating surfaces and tightened it up. Works like new bottom cam was only slightly worn. P.S. Remove everything from the door first.

I was set to buy a new magnetic seal to hold the door closed, when I looked it up on PartSelect I saw the recommendation that the problem might be the door closing cam.. I check it with a mirror and sure enough the cam had broken and the door sagged about 1/4 inch. I then followed the instruction and removed the top hinge, lifted the door ... Read more off and replaced the cam. I did need two and the one attached to the lower hinge had to be drilled out and a new screw and nut attached to hold the cam. It was simple to do, I would recommend selling the door closing cam be sold in pairs with a #10 1/2 inch long screw with lock nut.

Removed door off hinge , remove bottom hinge, drill out rivet, lift off old cam & replace with new cam ,add new 1/4' BOLT(NOT SUPPLIED) to location where rivet was, reinstall bottom hinge & door ,check alignment, works perfect.

Thanks

Use small putty knife to cut internal sealant on ice maker door trim piece. Then you can easily remove it.

Remove front cover did not remove wires remove ice and water unit took off flapper put new one on 5 minutes back together