My Orders
- Home
- TFX24PFXAWW
- Instructions
TFX24PFXAWW General Electric Refrigerator - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Water Line Broke that brings water to the Door
11 of 24 people
found this instruction helpful.
-
Ather from Commerce, CA
- Really Easy
- 30 - 60 mins
-
Nutdriver, Pliers, Screw drivers
First Remove the screw and cover from the left top front of the fridge using a Phillips Screw Driver # 2
Then using a nut driver 1/4 of inch (or Socket set)
remove the two nuts holding the door hinge keeping the door in closed position. Now unplug the electrical connector between the door and the fridge body(Simply pulling it ap ... Read more art) Now hold the door from the middle and raise it up so that it can slide out from the bottom hole, on the main body
Now place the door on a table or a flat surface(Put may be a sheet or some thing to prevent the finish from getting scratched) Now remove the nuts around the inner panel of the door(nut Driver or Socket set) Remove the old lining and discard .Install the new lines and then replace every thing in the reverse order.
Note : Before tighting the top nuts of the door, make sure you keep the door aligened so you would not have to do it after completeing the job.
Then using a nut driver 1/4 of inch (or Socket set)
remove the two nuts holding the door hinge keeping the door in closed position. Now unplug the electrical connector between the door and the fridge body(Simply pulling it ap ... Read more art) Now hold the door from the middle and raise it up so that it can slide out from the bottom hole, on the main body
Now place the door on a table or a flat surface(Put may be a sheet or some thing to prevent the finish from getting scratched) Now remove the nuts around the inner panel of the door(nut Driver or Socket set) Remove the old lining and discard .Install the new lines and then replace every thing in the reverse order.
Note : Before tighting the top nuts of the door, make sure you keep the door aligened so you would not have to do it after completeing the job.
Read less
Was this helpful?
Thank you for voting!
crushed ice feature inoperative, broken pieces in water dispensed.
6 of 9 people
found this instruction helpful.
-
Jim from Jacksonville, FL
- Really Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers
Found broken pieces of deflector in delivered ice. Removed dispenser, carefully disassembled it, marking fasteners, sprimgs, and levers. Local repaimen say no replacement part available, must replace entire ice maker @ $350. Found exact part in your online reference, ordered at price of $3.76, part arrived two days later--perfect fit, exa
... Read more
ctly same as original. Reassembled, and it works exactly like new. Family very happy. Good job!!!!!
Read less
Was this helpful?
Thank you for voting!
Fresh Food section door made a click noise on closing
5 of 6 people
found this instruction helpful.
-
Charles from Renton, WA
- Easy
- 15 - 30 mins
-
Screw drivers, Socket set
Since the cam riser was obviously broken I obtained a replacement.
It also broke. The door hinge cam needed to be replaced also.
To repair Remove the hinge cover using a #2 phillips driver. Than remove the Hinge using an 8mm socket. Turn the door upside down and, using an 8mm socket remoge the cam riser and the door hinge cam. ... Read more r />Replace in reverse order.
Be sure to inspect all parts and order all required.
It also broke. The door hinge cam needed to be replaced also.
To repair Remove the hinge cover using a #2 phillips driver. Than remove the Hinge using an 8mm socket. Turn the door upside down and, using an 8mm socket remoge the cam riser and the door hinge cam. ... Read more r />Replace in reverse order.
Be sure to inspect all parts and order all required.
Read less
Was this helpful?
Thank you for voting!
Tubing from vavle to reservoir had been degraded by compressor heat and had cracked, leaking water when door water dispenser was used.
6 of 10 people
found this instruction helpful.
-
Scot from Fort Collins, CO
- Difficult
- More than 2 hours
-
Nutdriver, Screw drivers, Wrench set
- Disconnect the valve assembly and remove electrical connection to water dispenser valve to prevent accidental water discharge
- Disconnect tubing from valve assembly, remove and keep compression nut.
-Disconnect tubing from junction to door tube remove and keep compression nut
-Remove screws used to moun ... Read more t reservoir, pull tubing into main refrigerator compartment and remove old reservoir and tubing.
- Note that one of the tubes on the new reservoir is 2' too short.
- Go to hardware store to purchase 5/16" universal tubing compression junction.
- Install reservoir and feed tubing through holes in main refrigerator compartment.
- Route tubing through woven tubing protectors and clips.
- Trim tubing to length and install in valve using old compression nut.
- Splice the piece of tubing trimmed from supply side of reservoir to the outlet side tube using the fitting purchased from the hardware store.
- Connect end of tubing to existing junction using old compression nut.
- Re-connect wires to valve solonoid and test for leaks.
- Re-install valve assembly to refrigerator frame.
- Disconnect tubing from valve assembly, remove and keep compression nut.
-Disconnect tubing from junction to door tube remove and keep compression nut
-Remove screws used to moun ... Read more t reservoir, pull tubing into main refrigerator compartment and remove old reservoir and tubing.
- Note that one of the tubes on the new reservoir is 2' too short.
- Go to hardware store to purchase 5/16" universal tubing compression junction.
- Install reservoir and feed tubing through holes in main refrigerator compartment.
- Route tubing through woven tubing protectors and clips.
- Trim tubing to length and install in valve using old compression nut.
- Splice the piece of tubing trimmed from supply side of reservoir to the outlet side tube using the fitting purchased from the hardware store.
- Connect end of tubing to existing junction using old compression nut.
- Re-connect wires to valve solonoid and test for leaks.
- Re-install valve assembly to refrigerator frame.
Read less
Was this helpful?
Thank you for voting!
Ice maker would not dispense ice cubes
6 of 10 people
found this instruction helpful.
-
Barbara from Medical Lake, WA
- Really Easy
- Less than 15 mins
-
Screw drivers
Removed the face plate (4 screws) on the ice bucket/auger and put it on the new unit.
Was this helpful?
Thank you for voting!
Broken light shield in freezer
4 of 4 people
found this instruction helpful.
-
Cathy from San Antonio, TX
- Really Easy
- Less than 15 mins
-
Screw drivers
SUPER easy repair, taking about 5 minutes. After taking out the ice bin, I removed one small phillip's head screw, put the light shield in place, and tightened the screw.
Was this helpful?
Thank you for voting!
I had a smell from the ice and bad taste
5 of 7 people
found this instruction helpful.
-
Henry from Rockville, MD
- Really Easy
- Less than 15 mins
-
Screw drivers
I removed the 4 screws from the cover and replaced the auger and ice bucket assembly. Extremely simple and I was amazed how easy it was.
Was this helpful?
Thank you for voting!
Dispenser Water Reservoir failed seem
5 of 8 people
found this instruction helpful.
-
Scott from South Lake Tahoe, CA
- Really Easy
- Less than 15 mins
-
Nutdriver, Screw drivers
This was a very easy fix. I cut the water lines at the reservoir, coupled the old lines to the new lines with two plastic barbed fittings used for outdoor drip irrigation. All I had to do was pull the old lines out and the new lines followed. Easy as pie!
Was this helpful?
Thank you for voting!
Rusted Auger and Broken Ice Bin Door
4 of 5 people
found this instruction helpful.
-
JOHN from CONROE, TX
- Really Easy
- Less than 15 mins
-
Screw drivers
After bagging the ice in the old bin and rinsing out the new bin, I removed 4 screws that held the old ice bin facing/door frame to the old ice bin and the facing came right off. Then I just screwed the facing on the new ice bin, popped the new door into place, and put the new ice bin back into the freezer. Although web descriptions for
... Read more
the parts I ordered referenced GE and other appliance brands and not Kenmore at all, the search engine led me to these parts and everything fit perfectly.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
ice bucket was broken
5 of 8 people
found this instruction helpful.
-
ROY L from TIGRETT, TN
- Really Easy
- Less than 15 mins
-
Screw drivers
it was really easy now it works like it did when it was brand new
Was this helpful?
Thank you for voting!
Auger was rusted causing brown spots in ice and metal pieces in water
4 of 5 people
found this instruction helpful.
-
Jane from Clifton, NJ
- A Bit Difficult
- More than 2 hours
-
Nutdriver, Pliers, Screw drivers
Took unit apart but did not take photos of how to put unit back together, so needless to say it took longer then it should have. My error. Ordering the part was very easy and within days the part arrived at my door. Should the need arise, I would order again from Part Select.com.
Was this helpful?
Thank you for voting!
would not crush ice
3 of 3 people
found this instruction helpful.
-
Larry from Mount Airy, NC
- A Bit Difficult
- 30 - 60 mins
-
Nutdriver, Screw drivers
you must pay careful attention when taking the dispenser apart,especially the long rod that controls the deflector,but if close attention is payed to disassembly you should have no problem.
Was this helpful?
Thank you for voting!
Door was squeaky and would no close
3 of 3 people
found this instruction helpful.
-
Ronald from Yuma, AZ
- Really Easy
- Less than 15 mins
-
Nutdriver
I layed several small 2x4 blocks on the floor, then raised the door up from the hinge, using the small pry bar. Then removed the the screws for the hinge. Removed the screws holding the door stop and removed the door cam. Then, I replaced the door closing cam. Replaced the hinge and screws. I Lowered the door on to the hinge and ap
... Read more
plied a little lubricant to the cam and job complete.
Read less
Was this helpful?
Thank you for voting!
drawer was broken
3 of 5 people
found this instruction helpful.
-
Mary from Fort Collins, CO
- Really Easy
- Less than 15 mins
The replacement part fit perfectly and was easy to install. No problems at all.
Was this helpful?
Thank you for voting!
Broken Light Shield
3 of 5 people
found this instruction helpful.
-
Jeffrey from Cumming, GA
- Really Easy
- Less than 15 mins
-
Screw drivers
Removed the Ice Maker container. Removed the one screw that held the remnant of the old light shield. Placed the new light shield in place and installed the screw. 5 Minutes from start to finish.
Was this helpful?
Thank you for voting!