Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Ice chute frosted up
6 of 9 peoplefound this instruction helpful.
Phillip from Springfield, VA
Easy
30 - 60 mins
Screw drivers
Procedure for Replacing the Ice Chute Plate 1. Turn off the power. 2. Snap off the outside trim ring. Use a plastic screwdriver to avoid scratching the cabinet. 3. Locate the three small holes below the control panel facing, just above ice chute. The center hole is not used. With a small, blunt, object (wire – blunted nail)
... Read more that is slightly smaller than the holes, push up rather firmly up through the outer holes to release front control panel. 4. Remove the three wire connectors from printed circuit board. Firmly pull/pry them straight out of retaining clip. Use caution: Excessive force will break clips. 5. Release the secondary panel by removing four screws (one in each corner). 6. Remove the flap assembly. 7. Clean all accessible areas with 1/10 bleach water to sanitize. Rinse the cleaned area with clear water and thoroughly dry everything before re-assembling the panel. 8. Install the new flap assembly. 9. Re-installed everything in the reverse order and check the functionality. 10. Order a spare ice chute flapper to be ready for the next event.
Read less
Was this helpful?
Thank you for voting!
Fresh Food section door made a click noise on closing
5 of 6 peoplefound this instruction helpful.
Charles from Renton, WA
Easy
15 - 30 mins
Screw drivers, Socket set
Since the cam riser was obviously broken I obtained a replacement. It also broke. The door hinge cam needed to be replaced also. To repair Remove the hinge cover using a #2 phillips driver. Than remove the Hinge using an 8mm socket. Turn the door upside down and, using an 8mm socket remoge the cam riser and the door hinge cam.
... Read morer />Replace in reverse order. Be sure to inspect all parts and order all required.
Read less
Was this helpful?
Thank you for voting!
crushed ice feature inoperative, broken pieces in water dispensed.
6 of 9 peoplefound this instruction helpful.
Jim from Jacksonville, FL
Really Easy
30 - 60 mins
Nutdriver, Screw drivers
Found broken pieces of deflector in delivered ice. Removed dispenser, carefully disassembled it, marking fasteners, sprimgs, and levers. Local repaimen say no replacement part available, must replace entire ice maker @ $350. Found exact part in your online reference, ordered at price of $3.76, part arrived two days later--perfect fit, exa
... Read morectly same as original. Reassembled, and it works exactly like new. Family very happy. Good job!!!!!
Read less
Was this helpful?
Thank you for voting!
The Ice Flapper warped and clogged up the Ice Shoot
5 of 6 peoplefound this instruction helpful.
Ronald from Elkridge, MD
Really Easy
15 - 30 mins
Screw drivers
I bought a Flapper replacement part from Parts Select. I installed it following their very complete on-line video directions. Their complete and easy to follow directions made my job very easy, and the work was completed without any problems and just as good as if it were done by a professional repair person. I am proud of my work, it
... Read morecouldn't have been done without their video insructions. Also I got delivery of the part within two days of my order. I will alway look for Parts Select any time I need an applicance repaired. Thanks to Parts Select!
Read less
Was this helpful?
Thank you for voting!
The vegetable pan was broken from closing the door on it too hard when still open
4 of 4 peoplefound this instruction helpful.
John from Randle, WA
Easy
Less than 15 mins
I just slide the new one in place, using exsisting sliders. I had to remove the old grab handle from old pan and snap it into place on new pan.
Was this helpful?
Thank you for voting!
There was a warm spot at the front edge of dividing wall. The fan motor was not working.
4 of 4 peoplefound this instruction helpful.
Kathrine from FORT MILL, SC
Really Easy
30 - 60 mins
Nutdriver, Pliers, Screw drivers, Socket set
I followed the directions of Steve on the installation video. He makes it easy to do the repair with his step by step description of the installation. I have repaired three different aging appliances with help of Steve and PartSelect's very helpful Customer Service. I wish Steve a wonderful retirement and hope PartSelect can find
... Read more someone as easy to follow for future videos. The videos are priceless for the repairs.
Read less
Was this helpful?
Thank you for voting!
Tubing from vavle to reservoir had been degraded by compressor heat and had cracked, leaking water when door water dispenser was used.
6 of 10 peoplefound this instruction helpful.
Scot from Fort Collins, CO
Difficult
More than 2 hours
Nutdriver, Screw drivers, Wrench set
- Disconnect the valve assembly and remove electrical connection to water dispenser valve to prevent accidental water discharge
- Disconnect tubing from valve assembly, remove and keep compression nut.
-Disconnect tubing from junction to door tube remove and keep compression nut
-Remove screws used to moun
... Read moret reservoir, pull tubing into main refrigerator compartment and remove old reservoir and tubing.
- Note that one of the tubes on the new reservoir is 2' too short.
- Go to hardware store to purchase 5/16" universal tubing compression junction.
- Install reservoir and feed tubing through holes in main refrigerator compartment.
- Route tubing through woven tubing protectors and clips.
- Trim tubing to length and install in valve using old compression nut.
- Splice the piece of tubing trimmed from supply side of reservoir to the outlet side tube using the fitting purchased from the hardware store.
- Connect end of tubing to existing junction using old compression nut.
- Re-connect wires to valve solonoid and test for leaks.
- Re-install valve assembly to refrigerator frame.
Read less
Was this helpful?
Thank you for voting!
Dispenser Water Reservoir failed seem
5 of 8 peoplefound this instruction helpful.
Scott from South Lake Tahoe, CA
Really Easy
Less than 15 mins
Nutdriver, Screw drivers
This was a very easy fix. I cut the water lines at the reservoir, coupled the old lines to the new lines with two plastic barbed fittings used for outdoor drip irrigation. All I had to do was pull the old lines out and the new lines followed. Easy as pie!
Was this helpful?
Thank you for voting!
Water line was leaking
4 of 5 peoplefound this instruction helpful.
Doug from MODESTO, CA
Really Easy
Less than 15 mins
Nutdriver, Pliers, Wrench (Adjustable)
The internal water line was leaking. I could not find any repair parts for my refrigerator but the GE 5/16 water line was the same size. I purchased 6' of tubing and two unions. Make sure the clean and square. If possible, make the cuts in a spot where you can use the pliers and wrench to tighten the union. I cut approximately 2' out of t
... Read morehe existing line and replaced it with the same length of new line using the 2 unions, one on each end. Took about 5 minutes.
I layed several small 2x4 blocks on the floor, then raised the door up from the hinge, using the small pry bar. Then removed the the screws for the hinge. Removed the screws holding the door stop and removed the door cam. Then, I replaced the door closing cam. Replaced the hinge and screws. I Lowered the door on to the hinge and ap
... Read moreplied a little lubricant to the cam and job complete.
Read less
Was this helpful?
Thank you for voting!
5/16" tubing to chilled water dispenser cracked
4 of 6 peoplefound this instruction helpful.
Mark from Indian Trail, NC
Easy
15 - 30 mins
Nutdriver
Cut out cracked tubing between valve and where tubing enters into refrigerator. Cut new tubing to length and attach to existing using union.
you must pay careful attention when taking the dispenser apart,especially the long rod that controls the deflector,but if close attention is payed to disassembly you should have no problem.
Was this helpful?
Thank you for voting!
The existing auger was rusty and made the ice taste bad.
5 of 10 peoplefound this instruction helpful.
Scott from martinez, CA
A Bit Difficult
15 - 30 mins
Screw drivers
Removed the screws holding the faceplate. Then couldn't change out the auger so needed to remove all of the other screws in the unit and fully disassemble the icemaker unit. Should have marked the parts as I took them apart as I needed to find a parts diagram on-line to reassemble. Not sure that I put them back together right as the un
... Read moreit will not dispense whole ice cubes as it did previously.
Read less
Was this helpful?
Thank you for voting!
Old auger was rusting
4 of 7 peoplefound this instruction helpful.
ROBERT from FREEHOLD, NJ
Easy
30 - 60 mins
Nutdriver, Pliers, Screw drivers
removed old auger; replaced it with a stainless steel auger
Was this helpful?
Thank you for voting!
The auger and ice bucket assembly was worn out and rusty
3 of 4 peoplefound this instruction helpful.
Philip from Sterling, VA
Easy
Less than 15 mins
Screw drivers
I simply removed the screws holding the plastic face plate to the old auger/ice bucket and attached it to the new one. It was a simple procedure
My Orders
