My Orders
- Home
- TFT22JABCAA
- Instructions
TFT22JABCAA General Electric Refrigerator - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
The light inside the oven had burned out
3 of 7 people
found this instruction helpful.
-
Catherine from SEATTLE, WA
- Very Easy
- Less than 15 mins
0. As a safety precaution, unplug the range or hit the relevant fuse breaker before you start. You might also want to grab a flashlight. Definitely do not try to do this while the oven is hot.
1. Pinch the wire over the light bulb cap to remove it. This is inside the oven at the back.
2. Pop off the hemispherical glass cap.
... Read more />3. Unscrew the old light bulb, and screw the new light bulb in its place.
4. Put the cap back.
5. Secure the cap by putting the wire back in its slots on the cap.
No tools needed, the cap is just held in place with pressure from the wire.
1. Pinch the wire over the light bulb cap to remove it. This is inside the oven at the back.
2. Pop off the hemispherical glass cap.
... Read more />3. Unscrew the old light bulb, and screw the new light bulb in its place.
4. Put the cap back.
5. Secure the cap by putting the wire back in its slots on the cap.
No tools needed, the cap is just held in place with pressure from the wire.
Read less
Was this helpful?
Thank you for voting!
plastic cam risers on fresh food door worn out
1 person
found this instruction helpful.
-
Fred from Port St Lucie, FL
- Really Easy
- 15 - 30 mins
-
Screw drivers, Socket set
I unloaded the door and took the cover off at the top of the upper hinge (1 phillips screw) I then unbolted the upper hinge (2-28mm bolts) and lifted the door off. I was surprised how light it was. I laid the door down and installed the new cam riser on the door. I then unbolted the lower hinge (2-28mm bolts)and installed the new hinge.
... Read more
r />I lubed the 2 hinges with vaseline and put the door back on the lower hinge. I then reinstalled the upper hinge and cover. It took about 15 minutes, and a lot of that was cleaning up. Oh yes, to get at the lower hinge you have to pull off the lower grate that covers the coils. It just snaps off and on. It was a very easy job.
Read less
Was this helpful?
Thank you for voting!
door would not close by itself - broke cam riser
1 person
found this instruction helpful.
-
Mike from Alpharetta, GA
- Easy
- 15 - 30 mins
-
Nutdriver, Wrench (Adjustable)
My right door (food door on side-by-side) stopped closing - I found pieces of the plastic washer (cam riser) on the floor. After reading the stories on the web I decided to order the new part - and YES there are many universal parts that work for Kenmore/GE. The part comes with two parts (hinge and cam riser) - you should install both to
... Read more
insure a good fit. I took 3 blocks of wood and a shim and supported the bottom center of the door, unscrewed the hinge off and dropped it out (3 minutes). The "only" tough part was unscrewing the cam riser from the bottom of the door - it required a very small socket and you will only have about 6-8 inches of work space. Be sure you have a socket that fits before you take the hinge off. The entire repair took less than 30 minutes and contrary to some of the posts, you DO NOT need to take the door off. Good as new again!
Read less
Was this helpful?
Thank you for voting!
The food compartment door would not close completely.The botom door cams were worn.
1 person
found this instruction helpful.
-
Joseph from Pittsburgh, PA
- Easy
- 15 - 30 mins
-
Socket set
I removed the door from the bottom hinge assembly by removing the top hinge assembly.
1. Installed the cam to the bottom of the door.
2. Installed hinge and bottom pin & cam to the refrigerator.
3. Reinstalled door and adjusted front roller height to make door close better.
1. Installed the cam to the bottom of the door.
2. Installed hinge and bottom pin & cam to the refrigerator.
3. Reinstalled door and adjusted front roller height to make door close better.
Was this helpful?
Thank you for voting!
Emptied refrigerator door shelves. Supported door with 4x4 blocks.removed old door hinge and replaced with new.
1 person
found this instruction helpful.
-
John from Medford, OR
- Easy
- 15 - 30 mins
-
Socket set
Emptied refrigerator door shelves. Supported door with 4x4 blocks. Removed old door hinge and replaced with new door hinge and cams. Pleased with end result and dealing with PartSelect.
Was this helpful?
Thank you for voting!
Old hinge washer worn out.
1 person
found this instruction helpful.
-
James from Lockport, IL
- A Bit Difficult
- 15 - 30 mins
-
Socket set
First I placed a 2x4 under the frig door to keep it in place while I removed the hinge on the bottom of the door. I removed two screws holding the hinge and one screw holding the washer in place. I also loosened a screw adjacent to the washer so that I could more easily remove and replace the washer. The parts went in easily. The repa
... Read more
ir took much less time than I anticipated.
Read less
Was this helpful?
Thank you for voting!
The fresh food side of my refrigerator had started to drop because of a broken cam riser.
1 person
found this instruction helpful.
-
Lucas from Chandler, AZ
- Really Easy
- Less than 15 mins
-
Nutdriver, Socket set
First I pulled the door up to the top hinge and propped it up with phone books. Secondly I used a nutdriver with an 8mm attachment and removed the bottom hinge. Thirdly, I removed one screw from the bottom of the door with a socket and 8mm attachment and removed the broken cam riser. Being careful as to take note of how the cam was pos
... Read more
itioned. I then attached the new cam riser to the bottom of the door, attached the bottom hinge to the refrigerator, making sure the pieces (cam riser and plastic on bottom hinge) matched up and after everything was tight, removed the phone books. Remember to first remove the vent on the bottom of the refrigerator and it is much easier to maneuver the door if you empty the contents on the inside. Very easy, I am not very mechanically inclined and this is the first job that I finished in the amount of time as stated. Also, do not chance just the riser as both pieces will be worn. Hinge assembly comes with all you will need.
Read less
Was this helpful?
Thank you for voting!
Cam riser washers broken
1 person
found this instruction helpful.
-
Richard from Waltham, MA
- Easy
- Less than 15 mins
-
Wrench set
Easy repair. No need to remove the door. Simply prop up the door with blocks or books - remove hinge and riser assembly - replace with new parts. Total repair time about 15 minutes. Tools needed only an open end wrench.
Was this helpful?
Thank you for voting!
Door would not shut
1 person
found this instruction helpful.
-
Gregory from Glen Rock, PA
- Really Easy
- Less than 15 mins
-
Socket set
Really simple, I used a can of soup and a small piece of wood set under the door, and tapped it tight with the hammer to hold it in place while I removed the hinge. Two bolts at the bottom and two under the door itself. Installed the new hinge set, bolted tight and removed the shim.
The whole thing took less than 5 minutes
The whole thing took less than 5 minutes
Was this helpful?
Thank you for voting!
Bottom part was broken and the door would not close on it own.
1 person
found this instruction helpful.
-
Mark Andre from FREDERICKSBRG, VA
- Very Easy
- 15 - 30 mins
-
Screw drivers, Wrench set
Followed the video on the computer. Was fixed in no time. Works great.
Was this helpful?
Thank you for voting!
Closing Cam Broke
1 of 2 people
found this instruction helpful.
-
Brandon from Covington, TN
- Really Easy
- Less than 15 mins
-
Screw drivers, Socket set
Cake walk repair.
Unload the door then close it.
Remove screw holding plastic cover over hinge on top.
Remove 2 bolts attaching the hinge on the door.
Slowly open and lift door off of bottom hinge lay on counter.
Unscrew bolt, insert new cam, tighten bolt ,set back on bottom hinge, center install top hinge, ... Read more tighten and install cover. tool me 6 minutes.
Unload the door then close it.
Remove screw holding plastic cover over hinge on top.
Remove 2 bolts attaching the hinge on the door.
Slowly open and lift door off of bottom hinge lay on counter.
Unscrew bolt, insert new cam, tighten bolt ,set back on bottom hinge, center install top hinge, ... Read more tighten and install cover. tool me 6 minutes.
Read less
Was this helpful?
Thank you for voting!
Cam Riser On Lower Hinge Broke
1 of 2 people
found this instruction helpful.
-
Jim from Ridgeley, WV
- Really Easy
- Less than 15 mins
-
Screw drivers
Removed 2 screws holding top hinge. Removed door. Removed 2 screws that holds the door stop and cam riser replaced cam riser, provided, replaced stop and screws. Removed 2 screws holding lower hinge replaced with hinge, provided, replaced screws. Put door in place and replaced top hinge and srews. Job done
Was this helpful?
Thank you for voting!
cam riser craked
1 of 2 people
found this instruction helpful.
-
Kevin from Onley, VA
- Really Easy
- Less than 15 mins
-
Nutdriver
removed door, removed old cracked riser aand replaced with new. You have a easy to follow parts site and very good prices. I will use you for all my future repairs.
Was this helpful?
Thank you for voting!
Door would not close on its own
1 of 2 people
found this instruction helpful.
-
Rick from Yadlley, PA
- Really Easy
- Less than 15 mins
-
Screw drivers, Wrench set
I removed the top hinge, lifted the door off the bottom hinge, rmoved and replaced the bottom hinge assembly, and reinstalled the door. I then aligned the door and reinstalled the upper hinge. The fridge works just like new!
Was this helpful?
Thank you for voting!
the plastic slide cracked wouldn't support drawer
4 of 11 people
found this instruction helpful.
-
Cynthia from Hillsborough, NJ
- Really Easy
- Less than 15 mins
-
Screw drivers
Super simple! Hardest part of the entire process was identifying which part I needed to order. Once I received the part (which shipped promptly and was at my front door within 2 days), all it took was 5 mins and a screwdriver and I was back to having a usable snack drawer!
Was this helpful?
Thank you for voting!