My Orders
- Home
- TFK22PRDAAA
- Instructions
TFK22PRDAAA General Electric Refrigerator - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Frost buildup in freezer by the ice maker
1 person
found this instruction helpful.
-
Alex from Cary, NC
- Really Easy
- 15 - 30 mins
-
Screw drivers
Replaced dispenser door flapper by following the do it yourself video in this site. It was really easy. Just be careful when removing the dispenser black bezel. I broke one of the little tabs when taking it off.
Was this helpful?
Thank you for voting!
icemaker quit working when we moved
4 of 10 people
found this instruction helpful.
-
Regina from Taylorsville, KY
- Really Easy
- 15 - 30 mins
-
Screw drivers
My husband took out the old icemaker in about 5 minutes. The new icemaker was a perfect fit even though the refrigerator was >10yrs old. The only difficult part was the plug extension that was needed so that it would fit into an older appliance. The part was included, it just made the cord about 3 inches longer than it needed to. After wo
... Read more
rking with it for about 20 minutes we were able to fit it on the back side of the icemaker. Now it works great!!
Read less
Was this helpful?
Thank you for voting!
plastic cam risers on fresh food door worn out
1 person
found this instruction helpful.
-
Fred from Port St Lucie, FL
- Really Easy
- 15 - 30 mins
-
Screw drivers, Socket set
I unloaded the door and took the cover off at the top of the upper hinge (1 phillips screw) I then unbolted the upper hinge (2-28mm bolts) and lifted the door off. I was surprised how light it was. I laid the door down and installed the new cam riser on the door. I then unbolted the lower hinge (2-28mm bolts)and installed the new hinge.
... Read more
r />I lubed the 2 hinges with vaseline and put the door back on the lower hinge. I then reinstalled the upper hinge and cover. It took about 15 minutes, and a lot of that was cleaning up. Oh yes, to get at the lower hinge you have to pull off the lower grate that covers the coils. It just snaps off and on. It was a very easy job.
Read less
Was this helpful?
Thank you for voting!
The plastic hinge stops broke.
2 of 4 people
found this instruction helpful.
-
james from olney, IL
- Really Easy
- 15 - 30 mins
-
Screw drivers, Socket set
I cleaned out the door and removed the top hinge. Lifted the door and layed it on the floor. Removed bottom hinge from refridgerator installed new hinge. Replaced plastic stop on door. Used broke hinge to align it and tighten. Lifted door onto new hinge and installed top hinge. Instead of buying $35 dollar hinge buy 2 plastic stops. You
... Read more
'll have to drill out a rivet on bottom hinge but it will save over $30.00.
Read less
Was this helpful?
Thank you for voting!
Emptied refrigerator door shelves. Supported door with 4x4 blocks.removed old door hinge and replaced with new.
1 person
found this instruction helpful.
-
John from Medford, OR
- Easy
- 15 - 30 mins
-
Socket set
Emptied refrigerator door shelves. Supported door with 4x4 blocks. Removed old door hinge and replaced with new door hinge and cams. Pleased with end result and dealing with PartSelect.
Was this helpful?
Thank you for voting!
GE vegetable drawer broken.
1 person
found this instruction helpful.
-
Philip M. from SIMPSONVILLE, SC
- Very Easy
- Less than 15 mins
Concerned about removing and attaching front panel to broken drawer. Rep. said wasn't sure but most just snapped together. Rep. was correct. No tools required.
Was this helpful?
Thank you for voting!
Ice maker stopped working
1 person
found this instruction helpful.
-
Cary from ORLANDO, FL
- Really Easy
- 15 - 30 mins
-
Pliers
Remove the one screw holding the unit in place, unplug it, slide in the replacement, plug and screw it in.
Was this helpful?
Thank you for voting!
Bottom part was broken and the door would not close on it own.
1 person
found this instruction helpful.
-
Mark Andre from FREDERICKSBRG, VA
- Very Easy
- 15 - 30 mins
-
Screw drivers, Wrench set
Followed the video on the computer. Was fixed in no time. Works great.
Was this helpful?
Thank you for voting!
Had a drip which filled up the tray and leaked on the floor from water dispenser
1 person
found this instruction helpful.
-
Rudy from CITRUS SPGS, FL
- Very Easy
- 15 - 30 mins
-
Screw drivers
There are Great videos on YouTube!!! Turned off power,Removed trim ring, Pushed a philips head screwdriver in one of the holes underneath the electrical panel with the selector push buttons. This releases the electrical panel. There are Three wire sets with plugs. I removed the plugs and took the electrical panel out. Removed four Phillip
... Read more
s head screws and pulled out the big paddle switch. This then exposes the flapper. Replaced flapper with new one and reassembled everything. When I had everything apart, I cleaned with window cleaner. It was pretty moldy from the water leaking. Turned power back on and tested everything to make sure I didn't mess anything up. Works great
Read less
Was this helpful?
Thank you for voting!
The fresh food side of my refrigerator had started to drop because of a broken cam riser.
1 person
found this instruction helpful.
-
Lucas from Chandler, AZ
- Really Easy
- Less than 15 mins
-
Nutdriver, Socket set
First I pulled the door up to the top hinge and propped it up with phone books. Secondly I used a nutdriver with an 8mm attachment and removed the bottom hinge. Thirdly, I removed one screw from the bottom of the door with a socket and 8mm attachment and removed the broken cam riser. Being careful as to take note of how the cam was pos
... Read more
itioned. I then attached the new cam riser to the bottom of the door, attached the bottom hinge to the refrigerator, making sure the pieces (cam riser and plastic on bottom hinge) matched up and after everything was tight, removed the phone books. Remember to first remove the vent on the bottom of the refrigerator and it is much easier to maneuver the door if you empty the contents on the inside. Very easy, I am not very mechanically inclined and this is the first job that I finished in the amount of time as stated. Also, do not chance just the riser as both pieces will be worn. Hinge assembly comes with all you will need.
Read less
Was this helpful?
Thank you for voting!
My ice container and Ice chute were freezing up and getting blocked, and my filtered water line was also freezing
1 person
found this instruction helpful.
-
Joe from BRICK, NJ
- Really Easy
- Less than 15 mins
-
Screw drivers
I just followed the instructions on the video and it was exactly as they said......no surprises.
Was this helpful?
Thank you for voting!
Cam riser washers broken
1 person
found this instruction helpful.
-
Richard from Waltham, MA
- Easy
- Less than 15 mins
-
Wrench set
Easy repair. No need to remove the door. Simply prop up the door with blocks or books - remove hinge and riser assembly - replace with new parts. Total repair time about 15 minutes. Tools needed only an open end wrench.
Was this helpful?
Thank you for voting!
drawer facing cracked
3 of 7 people
found this instruction helpful.
-
Christine from Delray Beach, FL
- Really Easy
- Less than 15 mins
ordered drawer face - perfect part- snapped right in. done. order came within 10 days.
will order again if needed.
will order again if needed.
Was this helpful?
Thank you for voting!
Door would not shut
1 person
found this instruction helpful.
-
Gregory from Glen Rock, PA
- Really Easy
- Less than 15 mins
-
Socket set
Really simple, I used a can of soup and a small piece of wood set under the door, and tapped it tight with the hammer to hold it in place while I removed the hinge. Two bolts at the bottom and two under the door itself. Installed the new hinge set, bolted tight and removed the shim.
The whole thing took less than 5 minutes
The whole thing took less than 5 minutes
Was this helpful?
Thank you for voting!
Ice maker was not making ice.
1 of 2 people
found this instruction helpful.
-
Tina from Beaumont, CA
- Really Easy
- Less than 15 mins
-
Nutdriver, Screw drivers
First i removed two screws that holds the ice maker in, unplug the plug to the ice maker. I was able to remove the old one. Place the new one in screwed in the two screws and pluged in the plug and in just a little while i had ice again. I am a women, if i can do it any one can. I had a repair man tell me it was going to be $250.00 dollar
... Read more
s to replace it. I got on line ordered the ice maker and had it in 4 days. Very fast shipping and easy to install. Tina Kearns Beaumont, Calif
Read less
Was this helpful?
Thank you for voting!