TFH24PRSMBB General Electric Refrigerator - Instructions

Removed the 4 screws off the old bucket cover and place the cover on new bucket. Just that simply. Can't beat the price!!!

Replaced dispenser flapper

Determined that the little door that opens to allow full size cubes to fall was not opening. If you open freezer door, hold door switch in, select cubes and push in the lever that the glass pushes in you should hear the solenoid lift open which opens the little door. Mine was doing nothing. Removed ice bin and then removed icemaker motor ... Read more /solenoid section from back of freezer by disconnecting two wire harnesses and one screw. Found that solenoid smelled burnt and could see that inside of the solenoid was swollen out of round and burnt. Simple to replace.

Thanks to the stories on PartSelect my wife and I knew what to expect. The biggest hassle was sawing off the rivet that's on the hinge on the refrigerator (my wife volunteered for that job). When we got everything back together the door worked a lot better, but still wouldn't close without a little push. In frustration and running out ... Read more of time, we put the stuff back inside the refrigerator door and that did the trick! The weight was enough to allow the door to close on its own.

There was what seemed to be a half chewed up washer under the refig. door. The door wasn't closing all the way. DING!! Something was wrong!!

I looked up your schematic for the refrig door and decided what piece might have broken. It was a good guess and the part showed up a few days later.

I wedged up the refrig ... Read more door to take the tension off the lower bracket. Then, just took off the bracket and replaced the broken door closing cam.

I used a block of wood to hold up the door. Then unbolted the lower hinge from the fridge. That is when I found out that it was fine and it was the upper half of the hinge that was broken (worn).
So I unbolted the upper hinge (mounted on the bottom of door) It uses the same part. So I installed the part on the upper half of the hinge ... Read more .

I wish somebody would have told me that you need 2 of these for each hinge. The bottom one was in good shape, lucky for me.

First, I had to remove the face plate where the ice and water was dispensed remove 4 screws holding the electrical circuits, disconnect circuits ,remove 2 screws holding soleniod and one screw holdin crank assembly. repace parts and screws.

I removed two screws at the top of the door, lifted the door off. I got lucky: the broken cam was the one on the door (easy to remove), not the one on the body of the refrigerator (tough to remove).
There is a shim which was also broken - no way to know that ahead of time. I bent a 5/8" lock washer flat and it served acceptably a ... Read more s a shim.
It would be helpful if PartSelect.com could include with its listing of the cam, the fact that (1) the shim will probably be needed, and (2) there's a very good chance that you'll need TWO of the cams as well.

removed the door, installed the cam riser, and reattached the door. It took longer to remove the contents in the door than it did to install the cam riser.

I first removed all of the door contents. I then removed the door from its mountings by removing two screws at the bottom bracket. With the door lying on the floor I then removed the two screws holding the door cam assembly in place. I inserted the new door cam, then reversed the process replacing the four screws.

Replaced the old cams with new ones, door works perfect now.

Firts I removed the food from the freezer. Then I used the cordless drill/screw driver to loosen the broken piece of plastic. I inserted the plastic shield and screwed the shield in place. The majority of time was spent removing and replacing the food from the shelf.

Finding the part was made so easy by this website. I wish I h ... Read more ad done it years ago but because I am not handy, I didn't think I could do it. Reading how easily others did it convinced me to try.

removed top plate and raised the door off. I removed the L bracket from the fridge then noticed the part was rivited onto the L bracket. I cut the rivit and replaced the cam and used a small bolt and nut to sdecure it. Replaced the L bracket, the door, and the upper support. Only problem was the surprise rivit

Removed screws holding top door hinge. Lifted the door off bottom hinge. Unscrewed cam from bottom of door. Drilled out rivet holding the second cam in the bottom hinge. Replaced both cams using a flat headed bolt to hold the bottom cam. Dropped door into bottom hinge and replaced top hinge screws. Job done.

Make sure you buy t ... Read more wo cams and have a bolt to replace the bottom rivet.

Not a difficult job as long as you have a drill !!!

1. I removed the top door hinge.
2. I removed the door and laid it flat.
3. I replaced the cam attached to the bottom of the door. This was very easy.
4. I removed the bottom door hinge and had to remove the brad that held the second cam. This went well as I was able to saw it with a hacksaw.
5. Replaced the second ... Read more cam with a bolt and nut.
6. Replaced the door and top hinge.
7. Remember to order two cams when you do this repair.