My Orders
- Home
- TFH24PRSMBB
- Instructions
TFH24PRSMBB General Electric Refrigerator - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Ice chute frosted up
6 of 9 people
found this instruction helpful.
-
Phillip from Springfield, VA
- Easy
- 30 - 60 mins
-
Screw drivers
Procedure for Replacing the Ice Chute Plate
1. Turn off the power.
2. Snap off the outside trim ring. Use a plastic screwdriver to avoid scratching the cabinet.
3. Locate the three small holes below the control panel facing, just above ice chute. The center hole is not used. With a small, blunt, object (wire – blunted nail) ... Read more that is slightly smaller than the holes, push up rather firmly up through the outer holes to release front control panel.
4. Remove the three wire connectors from printed circuit board. Firmly pull/pry them straight out of retaining clip. Use caution: Excessive force will break clips.
5. Release the secondary panel by removing four screws (one in each corner).
6. Remove the flap assembly.
7. Clean all accessible areas with 1/10 bleach water to sanitize. Rinse the cleaned area with clear water and thoroughly dry everything before re-assembling the panel.
8. Install the new flap assembly.
9. Re-installed everything in the reverse order and check the functionality.
10. Order a spare ice chute flapper to be ready for the next event.
1. Turn off the power.
2. Snap off the outside trim ring. Use a plastic screwdriver to avoid scratching the cabinet.
3. Locate the three small holes below the control panel facing, just above ice chute. The center hole is not used. With a small, blunt, object (wire – blunted nail) ... Read more that is slightly smaller than the holes, push up rather firmly up through the outer holes to release front control panel.
4. Remove the three wire connectors from printed circuit board. Firmly pull/pry them straight out of retaining clip. Use caution: Excessive force will break clips.
5. Release the secondary panel by removing four screws (one in each corner).
6. Remove the flap assembly.
7. Clean all accessible areas with 1/10 bleach water to sanitize. Rinse the cleaned area with clear water and thoroughly dry everything before re-assembling the panel.
8. Install the new flap assembly.
9. Re-installed everything in the reverse order and check the functionality.
10. Order a spare ice chute flapper to be ready for the next event.
Read less
Was this helpful?
Thank you for voting!
Fresh Food section door made a click noise on closing
5 of 6 people
found this instruction helpful.
-
Charles from Renton, WA
- Easy
- 15 - 30 mins
-
Screw drivers, Socket set
Since the cam riser was obviously broken I obtained a replacement.
It also broke. The door hinge cam needed to be replaced also.
To repair Remove the hinge cover using a #2 phillips driver. Than remove the Hinge using an 8mm socket. Turn the door upside down and, using an 8mm socket remoge the cam riser and the door hinge cam. ... Read more r />Replace in reverse order.
Be sure to inspect all parts and order all required.
It also broke. The door hinge cam needed to be replaced also.
To repair Remove the hinge cover using a #2 phillips driver. Than remove the Hinge using an 8mm socket. Turn the door upside down and, using an 8mm socket remoge the cam riser and the door hinge cam. ... Read more r />Replace in reverse order.
Be sure to inspect all parts and order all required.
Read less
Was this helpful?
Thank you for voting!
Ice maker would not dispense ice cubes
6 of 10 people
found this instruction helpful.
-
Barbara from Medical Lake, WA
- Really Easy
- Less than 15 mins
-
Screw drivers
Removed the face plate (4 screws) on the ice bucket/auger and put it on the new unit.
Was this helpful?
Thank you for voting!
I had a smell from the ice and bad taste
5 of 7 people
found this instruction helpful.
-
Henry from Rockville, MD
- Really Easy
- Less than 15 mins
-
Screw drivers
I removed the 4 screws from the cover and replaced the auger and ice bucket assembly. Extremely simple and I was amazed how easy it was.
Was this helpful?
Thank you for voting!
Broken light shield in freezer
4 of 4 people
found this instruction helpful.
-
Cathy from San Antonio, TX
- Really Easy
- Less than 15 mins
-
Screw drivers
SUPER easy repair, taking about 5 minutes. After taking out the ice bin, I removed one small phillip's head screw, put the light shield in place, and tightened the screw.
Was this helpful?
Thank you for voting!
Rusted Auger and Broken Ice Bin Door
4 of 5 people
found this instruction helpful.
-
JOHN from CONROE, TX
- Really Easy
- Less than 15 mins
-
Screw drivers
After bagging the ice in the old bin and rinsing out the new bin, I removed 4 screws that held the old ice bin facing/door frame to the old ice bin and the facing came right off. Then I just screwed the facing on the new ice bin, popped the new door into place, and put the new ice bin back into the freezer. Although web descriptions for
... Read more
the parts I ordered referenced GE and other appliance brands and not Kenmore at all, the search engine led me to these parts and everything fit perfectly.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
ice bucket was broken
5 of 8 people
found this instruction helpful.
-
ROY L from TIGRETT, TN
- Really Easy
- Less than 15 mins
-
Screw drivers
it was really easy now it works like it did when it was brand new
Was this helpful?
Thank you for voting!
Auger was rusted causing brown spots in ice and metal pieces in water
4 of 5 people
found this instruction helpful.
-
Jane from Clifton, NJ
- A Bit Difficult
- More than 2 hours
-
Nutdriver, Pliers, Screw drivers
Took unit apart but did not take photos of how to put unit back together, so needless to say it took longer then it should have. My error. Ordering the part was very easy and within days the part arrived at my door. Should the need arise, I would order again from Part Select.com.
Was this helpful?
Thank you for voting!
would not crush ice
3 of 3 people
found this instruction helpful.
-
Larry from Mount Airy, NC
- A Bit Difficult
- 30 - 60 mins
-
Nutdriver, Screw drivers
you must pay careful attention when taking the dispenser apart,especially the long rod that controls the deflector,but if close attention is payed to disassembly you should have no problem.
Was this helpful?
Thank you for voting!
Door was squeaky and would no close
3 of 3 people
found this instruction helpful.
-
Ronald from Yuma, AZ
- Really Easy
- Less than 15 mins
-
Nutdriver
I layed several small 2x4 blocks on the floor, then raised the door up from the hinge, using the small pry bar. Then removed the the screws for the hinge. Removed the screws holding the door stop and removed the door cam. Then, I replaced the door closing cam. Replaced the hinge and screws. I Lowered the door on to the hinge and ap
... Read more
plied a little lubricant to the cam and job complete.
Read less
Was this helpful?
Thank you for voting!
Broken Light Shield
3 of 5 people
found this instruction helpful.
-
Jeffrey from Cumming, GA
- Really Easy
- Less than 15 mins
-
Screw drivers
Removed the Ice Maker container. Removed the one screw that held the remnant of the old light shield. Placed the new light shield in place and installed the screw. 5 Minutes from start to finish.
Was this helpful?
Thank you for voting!
Ice maker Auger and ice was rusty.
3 of 5 people
found this instruction helpful.
-
David from Danbury, TX
- Really Easy
- Less than 15 mins
-
Screw drivers
Pull out the old, dump the nasty ice. Remove 4 screws attached to the front cover. throw in trash, replace with new auger assembly, with 4 screws. Put it back in ice maker and let it make ice. Easy, cheap and never left the house to searc for the right part, found it on the front porch.
Was this helpful?
Thank you for voting!
LIGHT SHEILD BROKE.
2 of 2 people
found this instruction helpful.
-
PAUL from ALBUQUERQUE, NM
- Very Easy
- Less than 15 mins
SNAPPED THE NEW SHIELD IN PLACE. DONE!
Was this helpful?
Thank you for voting!
lights blown out
6 of 14 people
found this instruction helpful.
-
Gerald from WINTERVILLE, GA
- Very Easy
- Less than 15 mins
replaced lights in refrigirator and freezer
Was this helpful?
Thank you for voting!
Ice was discolored due to rust on auger
3 of 5 people
found this instruction helpful.
-
Angel from Chandler, AZ
- Really Easy
- Less than 15 mins
-
Screw drivers
Removed the old assembly from the refrigerator. Used a screwdriver to remove the four screws attaching the old assembly to the plastic front plates. Opened the box holding the new part (which had arrived very promptly at our doorstep), removed it and attached it very easily to the plastic front plates using the same four screws. Placed th
... Read more
e new assembly in the refrigerator and started making new ice. It was EASY!! We had read what others had said about this repair and knew it would be something we could do. Your website is very user friendly and helpful.
Read less
Was this helpful?
Thank you for voting!