TFG27PFXFWW General Electric Refrigerator - Instructions

The Ice flapper was warped therefore, it was not closing well. Because of this, the ice dispenser got air in it and the ice cubes would deice causing to make a chunk of ice inside.I went on line, order the part ($5.75 + tax= $12.00) checked Part Select video and did it myself. It really is as seen on the video. It took me less than 10 min ... Read more utes! I saved $200.00

I followed the Video on your website and that made it so easy and simple to follow. Thank you!

I watched the how to video and followed the instructions. The entire repair took less than 4 minutes. Hardest thing was disconnecting the control panel.

I followed the instructions on the youtube video on the company web page. I removed the cover by hand, removed the exisitng flapper door and install the new door, easy as pie.

Very Easy, follow direction I the video.

I watched the video on the PartSelect.com website and decided to give it a try. The replacement of the flapper was even easier than I anticipated! The old flapper was extremely warped and was allowing air into the freezer. I'm not sure how/why it was in that condition but I am happy to report that I have no more ice buildup. Thank you ... Read more , PartSelect!

I followed the directions on the video. Although my dispenser was a little different, I was able to get to the faulty door in less than five minutes.

I followed the instructions on the video presentation, stopping the video each time until I had completed the described step. Only one minor change from the video...my refrigerator door (stainless steel) does not have the plastic edging around the control panel as shown in the video. It took me a minute or two to figure out that I had t ... Read more o push the tabs on the bottom of the control panel. The rest was easy.

I am clueless around the house. But this was easy: Removed ice maker bin, fiddled with freezer shield to line up with the single screw hole that holds it in place. Use screwdriver to install shield with original screw that stayed in place after the original freezer mount cracked and broke. Put ice maker bin back. Done!

Easy to take apart just keep track of all your screws and parts most inportant of all are the 3 claw like and spacers that are inside the clear round part at the end of the ice bucket these pieces only turn in one direction if you put them on backwards or in the wrong order you will tear up your ice bucket so pay close attention when taki ... Read more ng it apart and reassembling it. One think that might be helpful is to take some pictures of the ice bucket before disassembly something i wish i had done prior to taking it apart. Some people download instructions off the internet but i felt like i could do it with out help well good luck

I followed the video instructions (very helpful) and used others comments for removing the control panel. For the latter I used a small allen wrench to carefully wedge the bottom two indents (look from below panel edge) slightly up and forward to release the panel. Next, after removing the four screws, the assembly (housing shield) remove ... Read more d fairly easily. I then had full access to the flapper and removed this carefully with the pliers so as not to damage the piece it was attached to (Dispenser Door Recess Crank?). The rubber outer flange on the otherwise plastic flapper was very irregular for approx. 1/4 of the circumference and thus did not seal. So far it's been one week and no more frost build up or frozen water dispenser line.

Replaced flapper, which was in surprisingly good condition. Major part of repair was removing a lot of mold incurred from long term seepage of room air into the ice channel. In the process of the repair, I discovered that the solenoid to the right of the flapper was hanging up badly. I removed it and cleaned both the plunger and the inter ... Read more ior cone of the solenoid with alcohol. This removed quite a bit of rust and some mold. Reinstalled solenoid, replaced flapper and it works just fine. May need to replace solenoid if problem recurs. Certainly worth $37.00!

I followed a video supplied with the e-mail notification of the shipment of the part. This was one of the best experiences I have had with locating, purchasing and installing a replacement part for an appliance.

I watched the Utube video, repeated the process at home while awaiting the part, and installed the flapper door in about 15 minutes after it arrived--piece of cake. The hardest part was removing the escutcheon plate on the front of the freezer door. I figured out I could slide a putty knife under it and the rest of the project was compl ... Read more eted in no time at all.

Your Video really made it easy, showing the actual replacment of the part. However I did have one problem, which was I could not unplug the panel just by pulling on the plugs. A locking catch is on each plug so I just moved the panel out of the way.