TFG27PFXFBB General Electric Refrigerator - Instructions

1. Use skewer to press plastic tabs under control panel, 2. Remove control panel and unplug solenoid, 3. Unscrew dispenser assembly and solenoid screws, 4. Press in tabs on lamp and remove assembly - unplug, 5. Replace lamp assembly, 6. Replace solenoid assembly and fasten scr ... Read more ews, 7. Replace flapper. 8. Replace other parts in reverse order.

The video to replace the flapper looks easy, howerer the first step is to remove thestic cover of the icemaker. In my refrigerator model (as oposed to teh one shown n teh video) teh coved if firmly attached and goes under the refrigerator external plate so I was never abel to take it oot (so step 1 failed).
I was able to replace the ... Read more flapper TROUGH the whole whre te ice comes from! this took lots of patients and someone with small hands!

Under the control panel there are three small holes. Insert ballpen or small flat screw driver on both outer holes to push a tab lock that holds the control panel in place. Then pull out control panel and three set of wires will be exposed and disconnect wire connectors (connectors have different sizes so you wont get confused in reconn ... Read more ecting). Unscrew four screws on each corner that holds the ice dispenser assembly (a part where you push your glass against to dispense ice or water. The flapper is exposed and easy to replace.

unclipped and replace with new part.

Turn off power
Remove operator faceplate by pullling out on outer lower corners
Disconnect wire connectors from circuit board
Remove four screws from dispenser and pull out dispenser assy
Replcae Door ASsembly
Put everything back in place
Power up
Job Done

Excellent video was available on the Parts Select website. It was simple. The selector panel pulled out by hand from the bottom. The subpanel was removed with the four screws. The flapper snapped out of the holder with two clips. The new one was inserted in reverse order.

Replaced dispenser flapper

First, I had to remove the face plate where the ice and water was dispensed remove 4 screws holding the electrical circuits, disconnect circuits ,remove 2 screws holding soleniod and one screw holdin crank assembly. repace parts and screws.

Firts I removed the food from the freezer. Then I used the cordless drill/screw driver to loosen the broken piece of plastic. I inserted the plastic shield and screwed the shield in place. The majority of time was spent removing and replacing the food from the shelf.

Finding the part was made so easy by this website. I wish I h ... Read more ad done it years ago but because I am not handy, I didn't think I could do it. Reading how easily others did it convinced me to try.

1. Unplug the fridge
2. Removed the outer facing of the dispenser outside the freezer door. This is fairly easy, better with a tool (plastic scraper) that won't mar the finish.
3. Removed the plastic plate with labels -- water, ice, etc. This is done by sliding a small jewelers screwdriver into the slots on the left, middle ... Read more and right in back of the plate. These are difficult to see without a flashlight.
4. Removed the four screws in the panel behind this plate.
5. Unpluged the large cable on the left side after the panel is freed.
5. Removed the rubber "dispenser" button. this just pulls off.
6. Remove the panel
7. Lift flapper up and remove. Clips hold this in.
8. Put new flapper in place.
9. Use reverse order to put back together.
Piece of cake. Ice maker no longer frosts up.!!!!

Removed ice dispenser trim from bottom-up and then removed control panel by gently pulling up from the bottom. Removed four screws holding dispenser chute and then two screws holing flapper assembly. Replaced gnarly old flapper with a new one and put all removed pieces back together.

Super fast replacement, and the part was sent to us FAST and WELL-PACKAGED and REASONABLY PRICED! Thankyouverymuch!

Followed the instructions and replaced the door recess.

Pulled the outter cover off, removed the electronic board, replaced the flapper and put it back together again.

I only installed a light shield. However, I injoyed using your web site. It was easy and much better than Repair Clinic web site. I'm a do it your self person and this is the site I will return to!