TFF24SCB General Electric Refrigerator - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Fridge door stopped closing.
1 person
found this instruction helpful.
-
Peter from Woodland Hills, CA
- A Bit Difficult
- 30 - 60 mins
-
Screw drivers, Socket set, Wrench (Adjustable)
The plastic door closing cams had broken after 17 years of use. It was tricky figuring out how the new cams fit as the old ones had disintegrated. Also you need 2 cams - not one. I first ordered only one. A detailed parts diagram would have helped. First unscrew the top door mount cover and then the top door mount. The fridge door t
... Read more
hen lifts up and off the lower door mount. Next is the hardest part - drilling off the old pop rivet which held the lower cam. The lower door mount had to be removed to get at the underneath of the pop rivet, and a bench vise was handy to hold it as I drilled off the old rivet. Then you need small stainless steel nut and bolt and split washer or lock nut to replace the rivet. Next unscrew the old upper cam from the underneath of the fridge door and replace. The large hole in the cam goes through the door hinge pins. The two plastic cams should interlock in a way that makes the door swing close. Anyway, now the door works fine.
Read less
Was this helpful?
Thank you for voting!
Door would not stay closed
1 person
found this instruction helpful.
-
Jennifer from Holt, MO
- Really Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers, Socket set
BUY TWO CAMS! Just like the others, both of the cams were shot. My husband & I did this ourselves & have NEVER attempted appliance repair before.
We propped the door up high enough to access the bottom hinge piece on the fridge & removed using socket. Removed the cover from the top hinge. Slid door down off the top hinge in able to g ... Read more et to the cam on bottom of door. Replaced this cam 1st in order to get door back on while worked to get the old cam off hinge. As others posted, this is rivited on. Used grinder to grind off rivit & hammer & punch to punch out. Attached new cam with bolt & nut found in our tin of leftovers. Inserted hinge into door & reattached to fridge. DONE! Not hard at all & didn't even argue the whole time.
We propped the door up high enough to access the bottom hinge piece on the fridge & removed using socket. Removed the cover from the top hinge. Slid door down off the top hinge in able to g ... Read more et to the cam on bottom of door. Replaced this cam 1st in order to get door back on while worked to get the old cam off hinge. As others posted, this is rivited on. Used grinder to grind off rivit & hammer & punch to punch out. Attached new cam with bolt & nut found in our tin of leftovers. Inserted hinge into door & reattached to fridge. DONE! Not hard at all & didn't even argue the whole time.
Read less
Was this helpful?
Thank you for voting!
door didn't close on its own..
1 person
found this instruction helpful.
-
George from Hawthorne, NY
- A Bit Difficult
- 30 - 60 mins
-
Screw drivers, Wrench set
Removed door off hinge , remove bottom hinge, drill out rivet, lift off old cam & replace with new cam ,add new 1/4' BOLT(NOT SUPPLIED) to location where rivet was, reinstall bottom hinge & door ,check alignment, works perfect.
Thanks
Thanks
Was this helpful?
Thank you for voting!
door didn't close by itselt
1 person
found this instruction helpful.
-
Louis from Anchorage, AK
- Really Easy
- 30 - 60 mins
-
Socket set
Placed blocks under the refrigerator door to take weight off the lower hinge pin. Removed the hinge by removing two screws into the refrigerator and two screws into the bottom of the door itself. This allows the hinge to be removed so the old nylon "closer" pieces can be removed (the one attached to the refrigerator has a rivet holding
... Read more
it in place so that has to be drilled out and replaced with a 3/16 inch bolt and nut). After re-attaching the nylon "closer" to the refrigerator side of the hinge and placing all the shims back in place, I re-attached the hinge to the door first, then the half hinge to the refrigerator. Had to line up the holes, tighten the screws and presto, the door closes like it was new again.
The freezer door side is more difficult as there are wires and a water line to work around.
The freezer door side is more difficult as there are wires and a water line to work around.
Read less
Was this helpful?
Thank you for voting!
Change bulb
3 of 8 people
found this instruction helpful.
-
Louis from LEAGUE CITY, TX
- Really Easy
- 30 - 60 mins
-
Nutdriver
Easy
Was this helpful?
Thank you for voting!
Refrigerator door was not closing by itself
1 of 2 people
found this instruction helpful.
-
MANUEL from PHILADELPHIA, PA
- A Bit Difficult
- 30 - 60 mins
-
Pliers, Screw drivers, Socket set
Please note that I did this repair 2 times before and it was very easy, it took me longer to get the stuff out of the refrigerator door.
But this time the existing upper and lower cams broke, and the lower part of the door was making contact with the screw that holds the lower cam to the lower support bracket damaging the head ... Read more of the screw.
Now I could not use a screw driver and I had to use a wrench and a vise grip to hold the round screw head (not easy), and then replace the screw and nut.
I had to insert 2 flat washers under the lower support, to separate the door an additional 1/32 from the ref. base to accomodate the fact that the door gasket had lost its regular shape in the lower part of the door (I discover this when I dismounted the door).
Then I removed the damaged cams, replace them with the new ones and now it is working ok.
Manny
But this time the existing upper and lower cams broke, and the lower part of the door was making contact with the screw that holds the lower cam to the lower support bracket damaging the head ... Read more of the screw.
Now I could not use a screw driver and I had to use a wrench and a vise grip to hold the round screw head (not easy), and then replace the screw and nut.
I had to insert 2 flat washers under the lower support, to separate the door an additional 1/32 from the ref. base to accomodate the fact that the door gasket had lost its regular shape in the lower part of the door (I discover this when I dismounted the door).
Then I removed the damaged cams, replace them with the new ones and now it is working ok.
Manny
Read less
Was this helpful?
Thank you for voting!
Broken drawer slide rail
1 of 2 people
found this instruction helpful.
-
Ralph from Pagosa Springs, CO
- Really Easy
- Less than 15 mins
-
Screw drivers
I unscrewed the broken slide rail and screwed in the new one. Voila!
Was this helpful?
Thank you for voting!
ice maker pump and water line leaking
2 of 5 people
found this instruction helpful.
-
Edward from Jenks, AL
- Really Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
I replaced both the punp and water line. the website depicting the repair parts was the best i ever worked with. The parts were high quality delivered on time and easy to install. Total job cost $30 as opposed the cost of of a service man or a new refrig.
Was this helpful?
Thank you for voting!
not closing. part broke.
1 of 2 people
found this instruction helpful.
-
Clinton from Melbourne, FL
- Really Easy
- 15 - 30 mins
-
Screw drivers, Wrench set
Watched the video very good. Thank You
Was this helpful?
Thank you for voting!
Both door Cams broken even though I could see only one.
1 of 2 people
found this instruction helpful.
-
Tom from Ammon, ID
- A Bit Difficult
- 30 - 60 mins
-
Socket set
I learned from previous descriptions. Most important is there are two cams so order two. Second is that the door can be blocked from the bottom so the door doesn't have to be unloaded if you are careful. Remove the vent cover. Raise the door as high as possible while closed then block it from dropping down. I used wooden blocks. Remove th
... Read more
e lower hinge and bracket on the bottom of the door. Put everythng back and you're back in business. A kit with both cams, spacers, and screws with diagram would have been nice to have.
Read less
Was this helpful?
Thank you for voting!
Refrigerator door wouldn't close properly due to broken cams.
1 of 3 people
found this instruction helpful.
-
Timothy from Rockville, MD
- Easy
- 1- 2 hours
-
Pliers, Screw drivers, Socket set
Thanks to the stories on PartSelect my wife and I knew what to expect. The biggest hassle was sawing off the rivet that's on the hinge on the refrigerator (my wife volunteered for that job). When we got everything back together the door worked a lot better, but still wouldn't close without a little push. In frustration and running out
... Read more
of time, we put the stuff back inside the refrigerator door and that did the trick! The weight was enough to allow the door to close on its own.
Read less
Was this helpful?
Thank you for voting!
door wouldn't close all the way.
1 of 3 people
found this instruction helpful.
-
Thomas from Las Vegas, NV
- Really Easy
- 15 - 30 mins
-
Socket set
There was what seemed to be a half chewed up washer under the refig. door. The door wasn't closing all the way. DING!! Something was wrong!!
I looked up your schematic for the refrig door and decided what piece might have broken. It was a good guess and the part showed up a few days later.
I wedged up the refrig ... Read more door to take the tension off the lower bracket. Then, just took off the bracket and replaced the broken door closing cam.
I looked up your schematic for the refrig door and decided what piece might have broken. It was a good guess and the part showed up a few days later.
I wedged up the refrig ... Read more door to take the tension off the lower bracket. Then, just took off the bracket and replaced the broken door closing cam.
Read less
Was this helpful?
Thank you for voting!
Door does not shut on its own
1 of 3 people
found this instruction helpful.
-
Gary from Sandy Hook, CT
- Easy
- 15 - 30 mins
-
Nutdriver
I used a block of wood to hold up the door. Then unbolted the lower hinge from the fridge. That is when I found out that it was fine and it was the upper half of the hinge that was broken (worn).
So I unbolted the upper hinge (mounted on the bottom of door) It uses the same part. So I installed the part on the upper half of the hinge ... Read more .
I wish somebody would have told me that you need 2 of these for each hinge. The bottom one was in good shape, lucky for me.
So I unbolted the upper hinge (mounted on the bottom of door) It uses the same part. So I installed the part on the upper half of the hinge ... Read more .
I wish somebody would have told me that you need 2 of these for each hinge. The bottom one was in good shape, lucky for me.
Read less
Was this helpful?
Thank you for voting!
Refrigerator door would not close properly
0 of 1 people
found this instruction helpful.
-
Joe from Woodbury, NJ
- Really Easy
- 15 - 30 mins
-
Socket set
I first removed all of the door contents. I then removed the door from its mountings by removing two screws at the bottom bracket. With the door lying on the floor I then removed the two screws holding the door cam assembly in place. I inserted the new door cam, then reversed the process replacing the four screws.
Was this helpful?
Thank you for voting!
door did not close automatically
0 of 1 people
found this instruction helpful.
-
Gerald from Charlotte, NC
- Easy
- 15 - 30 mins
-
Screw drivers
Removed screws holding top door hinge. Lifted the door off bottom hinge. Unscrewed cam from bottom of door. Drilled out rivet holding the second cam in the bottom hinge. Replaced both cams using a flat headed bolt to hold the bottom cam. Dropped door into bottom hinge and replaced top hinge screws. Job done.
Make sure you buy t ... Read more wo cams and have a bolt to replace the bottom rivet.
Not a difficult job as long as you have a drill !!!
Make sure you buy t ... Read more wo cams and have a bolt to replace the bottom rivet.
Not a difficult job as long as you have a drill !!!
Read less
Was this helpful?
Thank you for voting!