TFF20RBC General Electric Refrigerator - Instructions

Remove screw at hinge cover, top of door.
Remove two screw/nuts at hinge and remove hinge while holding door in place.
Lift door off of lower hinge
remove two nut/screws at bottom of door and replace closing cam. Be sure the pivot pin hole in the cam is lined up with the hole in door.

Next drill out rivet holdi ... Read more ng cam to lower hinge on the refer. Install cam with a pan head screw and nut (to replace rivet). It will help if you remove the plastic grille cover at the bottom of the frige.

Set door back on the lower pin and shut so the the magnetic strip holds the door in place. Re-install the upper hinge loosely. Adjust the door for an even gap and tighten the screw/nuts. Re-install the cover.

A very easy fix.

First of all, It was Christmas and no extra money to pay a repairman.
i got on the computer and started looking for a parts breakdown for an older GE side by side.
I finally found it and located the part I thought we needed.
I looked at several parts dealers and yours had the best price.
anyway it arrived in just 2 day ... Read more s. My son helped me remove the door and we put the new part on and I just saved the cost of a service call.

Thank You

Door needed to be supported before hinge assembly was removed. After replacing broken cam doors aligned and doors closing properly.

I first removed all of the door contents. I then removed the door from its mountings by removing two screws at the bottom bracket. With the door lying on the floor I then removed the two screws holding the door cam assembly in place. I inserted the new door cam, then reversed the process replacing the four screws.

Removed screws holding top door hinge. Lifted the door off bottom hinge. Unscrewed cam from bottom of door. Drilled out rivet holding the second cam in the bottom hinge. Replaced both cams using a flat headed bolt to hold the bottom cam. Dropped door into bottom hinge and replaced top hinge screws. Job done.

Make sure you buy t ... Read more wo cams and have a bolt to replace the bottom rivet.

Not a difficult job as long as you have a drill !!!

Thought I would only need one when I looked at the picture of the parts. Decided to order two just in case and after taking it apart both were broken. Needed two.
Took the top door bracket off and lifted the door off of the bottom bracket. Re-assembled cams, put a little white grease on all moving parts, placed the door into botto ... Read more m bracket and installed top bracket. Adjusted top bracket to make door line up with edge of refrigerator and all is well.

Removed refrigerator door and replaced bottom door pivot with the included mating cam and the door closing cam on the bottom of the door.

I didn't know that there were two mating cams and only ordered the door closing cam which I read online was the problem. It was the number one part on the part select list. The number two ... Read more part was a kit including the door closing cam and the pivot with mating cam attached. It would have been helpful if there had been some notes that said check condition of both cams before ordering the part. So I have a spare door closing cam and paid an extra $19 including $8 shipping which negated a return.

The repair is easy - getting the right parts the first time is the trick.

I did not realize I needed 2 cams to complete repair. Door cam was riveted in. I had to drill out rivet and replace with nut and bolt. Otherwise it went quite sommothly. At first I just replaced the cam on bottom of refridgerator but door was not quite right when closing. Further inspection showed the door had the other half of cam tha ... Read more t also needed replacement. Needed 2 orders. Paid for 2 shippings.

Why don't they just tell you that you have to buy 2 cams. I have now replaced the cams on both doors. The other door broke about 4 years ago. Fortunately the first time I read the user commetns or I would've bought just one. It is a quick easy fix. The longest step is drilling out and replacing the rivet. Everything else is done wit ... Read more h a nut driver.

Replaced the old cams with new ones, door works perfect now.

removed the door, installed the cam riser, and reattached the door. It took longer to remove the contents in the door than it did to install the cam riser.

Took the door contents out and put them on the counter, took the door off the hinges by unscrewing the 2 screws on the top of the Fridge and lifting the door off the hinge onthe bottom. Then laid down the Fridge on the kitchen floor and replaced the Door Closing Cam, keeping in mind the order of the 3 shims and other things on the bottom ... Read more of the door. Simple.

The bottom of the door was 5 " off the floor. A 2x4 block and a 4x4 block were pushed under the door and supported it while the water line was disconnected the hinge removed and the cam replaced. It was a simple fix and reading other people's experience made the repair so much easier.

Replaced both upper and lower cam's. Removed door from refrigerator, removed bolts on door cam on bottom of main door and replaced cam, then removed bolts from door hinge assembly, drilled out rivet holding on cam, replaced with new cam and re-riveted.

Removed the top cover using a Phillips screw driver to access the top 2 screws holding the bracket. Once the bracket was removed, lifted the door off the bottom hinge. Replaced the door closing cam, replaced shims and screws. Placed the door back on the bottom hinge, inserted the top bracket and secured.
This was the ultimate reso ... Read more lution to the problem. The problem I encountered was getting all of the correct parts. It took me 3 tries to finally identify and receive the parts needed to make the repairs. Using Part Select made it easy because they had the parts I needed. My 3 tries were partly my error and does not reflect on Part Select. I would recommend others use Part Select when choosing their replacement parts.