TES325KQ0 Estate Range - Instructions

I simply removed the elements and replaced the drip bowls with new ones. Put the elements back in and my stove looks %1000 better!

Unplugged burners. . . . . Removed old bowls and replaced with new. . . . . . Plugged burners back in. However, I do want you to know that I could not believe the promptness of your service and the courteous customer service person that assisted me with my problem in selecting the correct drip bowls. You are definitely a unique company!!!!

first I pulled the stove from the wall. Then unplugged the stove from the wall (electric stove) for safety. then I removed the middle back panel screws(2) and then the panel. I then pulled the wires off the heating element that was bad. I took the screws (2) off the heating element inside the oven. I had to use WD-40 to loosen the screws because with the heat they were really stuck. I removed the heating element and replaced it with the one I got through partselect.com. Put everything back and walla finished. Partselect.com sent me the right part at the right price and fast. No hassles at all.

I numbered every part. ex: 1 L., for first part removed left side. I used a magic marker to circle the holes and wrote the number of screws used on the part, set the srews in a separete place, so that I new where these screws went to. The cleanup was pretty time consuming, but I was able to keep my stove, when every repairman I called to fix my stove told me I was better off buying a new stove. ($600.00 stove 2 years old)Please Note: The insulation blanket needed for the entire stove is two pieces, the sides and top are one part # and the bottom and back, are another part #. I did not know this. I just purchased the top and sides. I got lucky, the back and bottom were still in good shape. So I guess I should have read the description of the part more carefully to see what it covers, before I ordered it. It took two people two hours to do the work, it was really nice to have an extra set of eyes, to remember what direction pieces of metal from the stove went. I would do it all over in a heart beat instead of buying a new stove.

Opened up the back of the stove. Unpluged the sensor. Replaced the sensor. Replace the back of the stove.

The sensor that has been replaced is not what is expected. After reading all of the instructions for adjusting the temperatures, the only temp that stays steady is when we first turn on the oven to 350 degrees. That stays steady but when I turn it to 400 it slowly goes up to 425 degrees.

I went to the local discount mart and bought drip bowls. The ones available at that store did not fit, so I decided to buy directly from the stove's manufacturer distributor.

The drip pans were simple to replace, as was the new burner element. My old one had broke and was still working, but I decided to replace it when I ordered the drip pans.

Everything was easy to install and it looks like a brand new new stove top! I saved a lot of money doing it myself.

Start by turning off the power to the range.
It was fairly easy to take the "Control Deck" off the top of the range by removing about 8 screws. I leaned the deck forward without removing any wires except a green ground that was held on by one of the screws.
There are two small screws under the switch knob holding the Infinite Switch to the panel. I removed these and let the switch hang on the wires. To avoid missplacing or crossing the wires... I moved one wire at a time to the new switch, then attached the switch to the panel and put it all back together.
Whole job was done in about 15 minutes

Replacing the bowls was simple, simply removing the burner units and pulling out the bowls and inserting the new ones.

The ONLY reason I am answering this questionaire is to complement Partselect.com for their incredibly fast shipping of my parts after I placed the order. I received my order within 2-3 days with normal shipping. I expected to wait at least a week or longer. Thanks again Partselect.com for being there when I needed you the most!

well had I known that the trim did not go over the glass, the project would have been easy, but I thought the trim held the glass in, but that was not the case. After much juggling discovered that the trim went under the glass, and at that point the instilation was very easy.

So often we feel inclined to contact repairmen for simple jobs. This was easy because I ordered the part by looking on the side of the range. It arrived in less than a week. I simply snap the bowls inside the correct sockets and now my stove looks new. I definitely would use this service again.

Went online and located the correct part, which I had shipped to me next day. The part arrived I removed the two screws which held the element in place, unclipped the two wire leads, then replaced old element with the new one, reattached wire clips then screwed new element in place. All done 10 min.

After turning off the circuit breaker, I removed the elements and pans, raised the top and cut the wires to the receptacle assembly. Stripped the wires, slid on the shrink tubing and applied the wire nuts. I used a hair dryer rather than a match to shrink the tubing. Reinstalled the drip pans and inserted the elements. The instructions were clear and the project was easy. The stove works like new.

Socket Lite come with clips attached to the outside
of the housing. After you unhook the 3 lead wires
that are attached to the unit. All you have to do is push in on the clips and release the unit. Then you
snap in the new unit. Attach the 3 wire leads, put a
oven bulb in the socket end, and the install the light cover

screwed in the new glide by taking out old broken one and screwing in new one. wife happy now.

Removed two screws that held the unit in then pulled out a few inches so I could see where the 5 wires were. Then I replaced one at a time till done. then replaced the retaining screws.