TED-265 Tanaka Gas Engine Drill - Parts

The fuel pipe/fuel line assembly is a genuine OEM parts kit used in gas-powered outdoor equipment with dimensions of 5mm x 160mm. It includes a pipe or line, which carries fuel from the tank to the carburetor, and a rubber grommet which holds the fuel line in place. The grommet also has a flange that prevents it from being pulled into the...Read more body of your equipment. Over time the grommet may wear down and the fuel line can become brittle and crack causing fuel leakages and difficulty starting or running your equipment. Therefore, it is important to routinely inspect this assembly and replace it when it shows signs of wear. Before your repair, drain the fuel for your safety and to prevent contaminating the fuel tank. To install a new fuel pipe assembly, simply pull off the old grommet and detach the fuel line. Carefully insert your new fuel line into the new grommet and connect the line to the carburetor and the fuel filter inside the fuel tank on your equipment.

This item has been OEM sourced to ensure a high level of quality. The clip is intended to be used with trimmers and blowers from Hitachi and Tanaka. The metal clip is part of the fuel system. The clip is used to fasten the fuel filter and the fuel line assembly. This part is priced as an individual replacement part.

This authentic OEM replacement spark plug is specifically designed for use with Tanaka power equipment and is sourced directly from the original manufacturer—not an aftermarket imitation. It delivers the electric current needed to ignite the air-fuel mixture in the engine’s combustion chamber, ensuring reliable performance. For optimal re...Read moresults, the spark plug should be properly gapped according to the specifications in your equipment’s owner’s manual. This item is sold individually and requires a spark plug wrench or socket wrench for installation or removal.

It is an authentic OEM sourced starter assembly, it is specially designed for use with Tanaka equipment. This is the mechanism that allows a user to pull-start the engine, over time any of the components may wear out and begin to fail eventually requiring a replacement. It is a complete assembly which includes the durable plastic housing,...Read more the starter pulley, the starter spring, and the pull rope with the grip, please note the hardware to secure it is sold separately.

This is a genuine Tanaka replacement part that has been sourced from the original manufacturer to be used with trimmers, edgers, hedge trimmers, blowers, and gas powered drills. The plastic pulley is used to store the starter rope and to engage the starter cam. This item is sold as an individual replacement part.

This piston ring is a small metal ring in an engine that seals the gap between the piston and the cylinder wall. It prevents the escape of combustion gases and maintains compression. When damaged, oil will leak into the combustion chamber and cause performance problems within the engine. You may experience rough running and a loss of powe...Read morer or notice that blue smoke is coming out from the exhaust when this happens. To remove the piston ring from your machine, you need to detach the piston from the engine. Using a small screwdriver, pry the damaged piston ring away from the piston and slide it off. Be careful not to scratch the piston nor the cylinder walls during this process. You may also need to compress the ring to remove or install it onto the piston. Please note that this authentic OEM replacement part is sold individually. It is recommended to replace your piston rings all at once as they wear out at the same rate, so be sure to read your user manual and confirm how many rings your machine will need.

It is a genuine replacement gasket which is supplied directly from the original equipment manufacturer for use with Tanaka power equipment. This special gasket provides an air-tight seal for the carburetor, over time material tends to deteriorate and may crack eventually requiring replacement to ensure peak performance. It is high-quality composite gasket which is sold individually.

This is an authentic Tanaka replacement part that has been sourced from the original manufacturer to be used with bike engines, chainsaws, blowers, gas powered drills, edgers, generators, trimmers, and powered augers. This screw is used with a variety of different types of machines and the application of the screw can vary based on the model of the equipment. The screw is available as an individual replacement part.

This is a genuine Tanaka replacement part, sourced directly from the manufacturer. The oil seal is found in many Tanaka power tools such as chainsaws and brush cutters. This part is a metal ring with a high-quality plastic inner ring, and is used to prevent oil leaks or contamination of the crank case. You may need a screwdriver and wrench to replace this part. This item is sold individually.

The pump filter body attaches to the fuel tank. It is an OEM replacement part for use in bicycle engines, trimmers, drills, generators, and brush cutters made by Tanaka. This is available as an individual replacement part and is made out of metal and a felt material. It might require a screwdriver, a set of pliers, a socket set, and a nutdriver to replace this part if it becomes broken or torn.