TC900QPDB0 Whirlpool Trash Compactor - Instructions

I ORDERDED THE SELECTOR SWITCH WHICH SITS BEHIND THE TOUCH PANEL THAT SAYS ON/OFF/START.i REMOVED THE 2 PHILLIPS SCREWS JUST BELOW THE DISPLAY.SLIDE THE WHOLE DISPLAY UP AND IT WILL EXPOSE 3 WIRES AND THE SWITCH.REMOVE THE TWO PHILLIPS SCREWS,REMOVE THE CLEARLY MARKED Y=YELLOW R=RED AND V=VIOLET .INSTALL THE WIRES MOUNT THE SWITCH REPLACE ... Read more THE TWO SCREWS REINSTALL THE PANEL,HIT START AND GOOD TO GO!

The plastic drive gear broke and the unit was locked in the down position. The repair kit contained all of the parts required to fix the problem plus other replacement parts for the gear drive unit. It was very easy (about 20 min.) to replace the gear and other parts. The unit works fine now.

I removed the plastic portion to get to the switch and wires. I removed the old switch by disconnecting the two wires and pushing it out of its setting.

I discovered the old switch only had 2 prongs where the new switch had 3. Once I figured which 2 of the 3 prongs would light the lightbulb,
I then connected the two w ... Read more ires to the correct prongs of the new switch. I pushed the new switch into its setting and replaced the plastic portion on the refrigerator. Voila, success. The refrigerator door now comes on when its door is opened.

Thanks for the having the part and getting it at our door step in 3 days.

Unplugged trash compactor and removed from undercounter. Took cover off and removed broken plastic gear. Replaced with new gear and put cover back on

Simply removed the two plastic gears (held on by some sort of clip), put the new gears in place using the spacing instructions that were provided in the kit ....... and it is working!

Compactor ram would go to bottom but not return back up after compaction. Keep running until unplugged. After unplugging flipped unit on its side and remover bottom plate (5) nut screws, exposing gears. Found that the main large gear had fine crack which caused it to spin loosely. Ordered gear assembly and lossened four mount screw on mo ... Read more tor to move it forward and give slack on chain. Hint: Loosen motor mount bolts, DO NOT REMOVE bolts COMPLETELY! Removed broken plastic gear and reassembled with new. Held/ pushed motor back to retention chain and secured four (4) mount bolts Then reassembled bottom plate with screw nuts and it worked perfectly!!

replaced switch and fixed the problem. Still had one more problem after that though, but got that figured out and fixed that to.

Removed two screws on the front panel cover and lifted off the cover , removed two small screws on the switch bracket, you need a short nut driver, removed the spade clipped wires from the old switch and replaced them on the new part and thats all there was to it.

I broke the directional switch trying to replace the power nuts..duh huh... ordered a new switch, took off the front panel ( 4 screws) replaced the switch (2 bolts) be careful not to lose the small threaded plate used instead of nuts to secure the switch.. and now it works like new again....partselect is a great resource for the diyer

Unscrew the bottom, pull out the chain, replace the gear.

I have always used compactor bags made of paper & plastic. I was sent bags made of only plastic. I called and was told that is the only kind available. I am concerned that the plastic bags may not be strong enough.

I quest I will have to try these all plastic bags. I hope they are strong enough and work properly.

-Removed the forward sliding rail screws...lifted the rails up several inches to access the wheel assembly...bent back the steel tab to access the nuts holding the wheels to the frame...replaced the wheels and bent back the steel tabs to original position. Trash bin now rolls out completely as before

Removed 4 screws and the foot release to attach the new guard. Replaced the foot pedal and 4 screws and was done.

changed out the switch and that fixed the problem

remove the container from base lay on floor unscrew 2 screws one on each side and remove foot pedal. I could see that the foot pedal had small bow in the pedal. You can only see this if you removed. I ordered the rollers in the front but did not install as it is not the rollers. Will keep for future if needed. Replace your foot first ... Read more if hard to open.