TBF23DFC General Electric Refrigerator - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Ice in freezer running down sides
8 of 9 people
found this instruction helpful.
-
P. Michael from Tustin, CA
- Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
This is a built-in unit. Remove the external bezel at the top of the unit. Reach through the unit and unplug the frig. On the compressor unit, you'll see a vertical metal panel. Remove the metal panel and the timer is right behind it. Remove one wire at a time and switch it to the new timer. Remove timer and replace with new one.
... Read more />
Just an added comment, GE Service wanted to put an "ice kit" into my unit. The full repairs would have cost $1,000. While I described how to replace the defrost timer, the problem was the tray heater. But that's another story.
... Read more />
Just an added comment, GE Service wanted to put an "ice kit" into my unit. The full repairs would have cost $1,000. While I described how to replace the defrost timer, the problem was the tray heater. But that's another story.
Read less
Was this helpful?
Thank you for voting!
defrost system kept freezing up
8 of 10 people
found this instruction helpful.
-
Robert from Williamstown, NY
- Easy
- 15 - 30 mins
-
Screw drivers
took out 4 screws - lowered timer cover - replaced timer- put it back together
Was this helpful?
Thank you for voting!
Refridgerator wouldn't cycle into defrost mode without doing it manually.
9 of 14 people
found this instruction helpful.
-
Ben from Warrior, AL
- Easy
- 15 - 30 mins
-
Screw drivers, Socket set
I removed the shield over the timer and the part that supported the timer. Just unpluged it and pluged in new timer and put back shield. I had already replaced the defrost heaters which had totally burned up. I also replaced the thermostat while I was making the repairs although the old one was still o.k. All the information that I needed
... Read more
to make the repairs I obtained through your website. After looking at several websites to compare prices-etc, I found yours to be the best overall. Thanks-a-million your website is worth it's weight in Cold Food !
Read less
Was this helpful?
Thank you for voting!
refrigerator wasn't cooling but the freezer was working properly
6 of 6 people
found this instruction helpful.
-
Don from BELLVILLE, TX
- Very Easy
- 15 - 30 mins
-
Nutdriver
From instructions found on the site I was directed to the defrost timer part being bad. And from the information others posted that have had the same problem I was able to replace that part by removing the bottom grill just below the door and on the left side was the part. Removing one screw to remove the bracket from the frame and then
... Read more
another screw to remove the part from the bracket. I found it easier to remove the part from the bracket before I pulled the part out so I would have more room to unplug the connector. Just reverse the steps to replace the new part. It took about a day or so for the refrigerator to get to the proper temp.
Read less
Was this helpful?
Thank you for voting!
broken fan blade in the freezer compartment
7 of 9 people
found this instruction helpful.
-
John from Cumberland, MD
- Really Easy
- Less than 15 mins
-
Pliers
Unplugged frige, removed top shelf, pulled broken fan blade off. Replaced with fan blade just purchased from PartSelect. Very simple repair. Orderd and recieved the right part.
Was this helpful?
Thank you for voting!
Started to see a little sweat in freezer and ice cream not getting hard frig staying on longer.
6 of 7 people
found this instruction helpful.
-
Frank from Philadelphia, PA
- Easy
- 15 - 30 mins
-
Socket set, Wrench set
Pulled frig out. Removed back cover. Unplugged frig, unplugged motor. Removed fan from old motor first then 3 screws from bracket that holds motor and removed motor. Reattached motor back on bracket, reattached fan on motor. Plugged fan back in and then frig. Everything worked fine no more soupy ice cream !!
Was this helpful?
Thank you for voting!
Not cooling - cond fan did not turn
6 of 7 people
found this instruction helpful.
-
Daniel from Great Falls, VA
- Easy
- 15 - 30 mins
-
Pliers, Screw drivers, Socket set
Unplug refrig! Removed back cardboard covering (~5 screws)
(1) Cleaned all the dust out (hardest part!)
(2) Removed power wire to motor
(3) Removed 3 bolts holding motor to frame
(4) Removed motor/fan blade to the left
(5) Moveded fan blade to new motor (clean it!)
(6) Replaced motor, reinstalled 3 bolts
... Read more >(7) Plugged power wire to new motor
(8) Tested it - worked fine, failed safe, drained to bilge!
Replaced back cover (had to tape it since I horked it up removing it)
(1) Cleaned all the dust out (hardest part!)
(2) Removed power wire to motor
(3) Removed 3 bolts holding motor to frame
(4) Removed motor/fan blade to the left
(5) Moveded fan blade to new motor (clean it!)
(6) Replaced motor, reinstalled 3 bolts
... Read more >(7) Plugged power wire to new motor
(8) Tested it - worked fine, failed safe, drained to bilge!
Replaced back cover (had to tape it since I horked it up removing it)
Read less
Was this helpful?
Thank you for voting!
light not working
7 of 11 people
found this instruction helpful.
-
robert from FRANKLIN SQ, NY
- Very Easy
- Less than 15 mins
-
Pliers, Screw drivers
I used pliers to pull lightly on the head of the switch, while I inserted a small flat head screw driver into the base of switch and gently worked around the edges to free it from the panel.
Was this helpful?
Thank you for voting!
unusually noisy
5 of 6 people
found this instruction helpful.
-
Anthony from South Plainfield, NJ
- Really Easy
- Less than 15 mins
-
Socket set
Removed the three screws from old motor body-bracket assembly , pulled off 1/4'' spade terminals and removed shield from terminal block for re-use.
Removed fan from old unit and installed on new,
screwed new motor in place, replaced terminal wires, plugged back in refrigerator.
Now my old rerfrigerator is whisper quiet
Removed fan from old unit and installed on new,
screwed new motor in place, replaced terminal wires, plugged back in refrigerator.
Now my old rerfrigerator is whisper quiet
Was this helpful?
Thank you for voting!
freezer cold but refrigerator warm, would not cycle the defrost on freezer
4 of 4 people
found this instruction helpful.
-
MATT from OAKLAND, MI
- Really Easy
- Less than 15 mins
-
Screw drivers
two screws and a connector were removed to replace the timer.
Timer was located on the top front of fridge
Timer was located on the top front of fridge
Was this helpful?
Thank you for voting!
Bad defrost timer
5 of 7 people
found this instruction helpful.
-
Bruce from Silver Spring, MD
- Really Easy
- 15 - 30 mins
-
Screw drivers
Parts Select made this an effortless process. From finding the part, ordering, to the online diagrams.
I'll be back...
I'll be back...
Was this helpful?
Thank you for voting!
Noisy refrigerator.
5 of 8 people
found this instruction helpful.
-
Rodney from Lafayette, LA
- Really Easy
- 15 - 30 mins
-
Screw drivers, Socket set
Remove the 4 screws holding the back cover onto the refrigerator. Unplug the power for the refrigerator. There's 3 bolts holding the fan motor assembly to the refrigerator. Loosen the two bolts which allow the brackets to pivot out , and remove the third bolt. Disconnect the electrical leads, and remove the fan blade, then rotate th
... Read more
e fan motor assembly out from the refrigerator. Install mounting brackets from the old motor onto the new motor, then reinstall the assembly in the reverse order of removal.
Read less
Was this helpful?
Thank you for voting!
Fan Stops - Bad Bearing
4 of 5 people
found this instruction helpful.
-
JACK R from LEESBURG, FL
- Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers, Socket set
Unplug unit from wall. Removed cover from rear of unit. Cleaned coils with vaccuum cleaner. Unplug wires from fan motor and remove nut holding fan blade to motor. Remove 3 screws holding motor to mount. Replace with new motor,make sure fan blade does not hit housing. Plug unit back in wall and replace cover.
Was this helpful?
Thank you for voting!
Refrigerator light wouldn't come on.
4 of 5 people
found this instruction helpful.
-
Daniel from Crown Point, IN
- Easy
- 15 - 30 mins
-
Pliers, Screw drivers
After replacing the light bulb and still no light I manually pushed the light switch button. Intermittently the light would come on then go out. I removed the power plug from the power source then replaced the light switch. I plugged the refrigerator back in and now I open the door the light comes on and stays on until the door is closed.
Was this helpful?
Thank you for voting!
Difficulty in removing the old switch
5 of 8 people
found this instruction helpful.
-
James from Federal Way, AL
- A Bit Difficult
- 30 - 60 mins
-
Screw drivers, Socket set
The old switch was hard to remove. Thinking that I may have to loosen the wires I used a socket wrench to remove a clamp. This was unnecessary. In the end the switch did come out using a large size screwdriver. The problem was that the expanding plastic tongue is not visible from the ouside so you have to try to feel your way around.
... Read more
If i had ordered the replacement before and not afterwards I would have seen this before hand.
Read less
Was this helpful?
Thank you for voting!