TBF20DFB General Electric Refrigerator - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Broken light switch
1 person
found this instruction helpful.
-
Deborah from BRADLEYVILLE, MO
- Very Easy
- Less than 15 mins
-
Pliers, Screw drivers
This was so easy I think it took me 2 minutes. I am not very mechanically inclined but that didn't matter! Works perfect thank you!
Was this helpful?
Thank you for voting!
Light went out in refrigerator
1 person
found this instruction helpful.
-
Gary from EAST JORDAN, MI
- Really Easy
- Less than 15 mins
-
Pliers, Screw drivers
Pop out switch, pull wires, attach wires to new switch and pop back in. Easy smeasy!
Was this helpful?
Thank you for voting!
Light Switch Not Working - Needed New Switch
1 person
found this instruction helpful.
-
Joe from SUGAR LAND, TX
- Really Easy
- Less than 15 mins
-
Screw drivers
Remove the top cover above the door by lifting it slightly and pulling forward. I used a mirror to make sure that there was nothing in the way of accessing the switch from above. I used a blade screwdriver to press against the switch retainer on the topside, while GENTLY prying from below with another blade screwdriver to get the switch d
... Read more
islodged. Once the retainer was past the opening, I wiggled the switch downward and then rotated it to the left when the rounded top right edge of the switch was visible. This allowed the wiring to the connector to pass thru the hole. I pushed the wiring from the top and pulled from below to get the connector below the opening for the switch. I then unplugged the switch, plugged in the new switch and reversed the removal process feeding the connector thru first then rotating the switch to the right to get the rounded edge of the switch thru the opening, then pressed the switch up into the opening until it snapped into place. Total time less than 10 minutes.
Read less
Was this helpful?
Thank you for voting!
40 year old refrigerator brittle light switch fell apart
1 person
found this instruction helpful.
-
Loren from EL PASO, TX
- Really Easy
- Less than 15 mins
-
Pliers, Screw drivers
with a jewelry screwdriver I pried the lock tab in and pulled switch down carefully, the hardest part was that the power wire connector was stuck on good but the pliers and the jewelry screwdriver was its match for a bout 5 minute for one connection a simple pull off prong connection. After the wire connected back to switch it popped back
... Read more
in SNAPP
Read less
Was this helpful?
Thank you for voting!
family member melted fan with hair dryer
1 person
found this instruction helpful.
-
Lauraine from Rocky Hill, CT
- Really Easy
- Less than 15 mins
-
Screw drivers
Unplugged fridge.Removed 2 screws holding a panel. After panel removed took off old fan and inserted new. Quite simple.
Was this helpful?
Thank you for voting!
Light would stay on when door closed
3 of 7 people
found this instruction helpful.
-
James from Glendale Heights, IL
- Really Easy
- Less than 15 mins
-
Nutdriver, Pliers
Extremely easy repair, the hardest part was getting the old switch out. I used a pair of needle nose pliers to squeeze the tabs in and it came right out.
Was this helpful?
Thank you for voting!
light switch freezer door
3 of 7 people
found this instruction helpful.
-
Sumlorq from Cleveland, OH
- Really Easy
- Less than 15 mins
put the gratefruit knife behind the old switch pooped it out pluged the new one in piece of cake 5min.even vacumed the dust off the coil
Was this helpful?
Thank you for voting!
water leaking from under dishwasher
1 person
found this instruction helpful.
-
Edward from E LONGMEADOW, MA
- A Bit Difficult
- 30 - 60 mins
-
Pliers, Socket set, Wrench (Adjustable)
Water was leaking from under the GE dishwasher, but once we pulled it out, had apparently been going on for a little while. Turning the water off to the dishwasher made it stop, so it was happening even when the unit was not running, potentially indicating somewhere early in the path of the water to and into the machine.
Indeed ... Read more , inspecting the water inlet vale showed a slow leak. Getting the replacement part was fine, and it fit the electrical, water inlet (existing 90-degree water inlet elbow), and water outlet connections just fine - but the original machine screws that held on the original water inlet valve did not work. It took a little research to figure out the new type of screw required, which was apparently a 10/16 Type AB, which seemed to be a less common type of sheet metal screw (with a point), as opposed to the original flat-ended machine screws. So, after ordering those separately (which were a bit expensive), it went together fine.
A note on the water inlet valve part just indicating the the threading on those parts has changed over time, so potentially ordering the screws to attach it might be worthwhile, would be good information to add about the water inlet valve.
Indeed ... Read more , inspecting the water inlet vale showed a slow leak. Getting the replacement part was fine, and it fit the electrical, water inlet (existing 90-degree water inlet elbow), and water outlet connections just fine - but the original machine screws that held on the original water inlet valve did not work. It took a little research to figure out the new type of screw required, which was apparently a 10/16 Type AB, which seemed to be a less common type of sheet metal screw (with a point), as opposed to the original flat-ended machine screws. So, after ordering those separately (which were a bit expensive), it went together fine.
A note on the water inlet valve part just indicating the the threading on those parts has changed over time, so potentially ordering the screws to attach it might be worthwhile, would be good information to add about the water inlet valve.
Read less
Was this helpful?
Thank you for voting!
Broken light switch
1 of 2 people
found this instruction helpful.
-
Ted from SANDWICH, IL
- Easy
- 15 - 30 mins
-
Screw drivers
took a little more effort than the video show to remove old module and replace new. Works fine now.
Was this helpful?
Thank you for voting!
Fan blade broken
2 of 5 people
found this instruction helpful.
-
John from Cumberland, MD
- Really Easy
- Less than 15 mins
Removed the broken fan blade (just pulled off) and replaced with part purchased PartSelect. Very easy repair, no tools required.
Was this helpful?
Thank you for voting!
Light was flicking
1 of 2 people
found this instruction helpful.
-
Stephanie from KEARNY, NJ
- Really Easy
- Less than 15 mins
-
Screw drivers
It was way to ez to install only a couple of minutes that's it
Was this helpful?
Thank you for voting!
The door activated light switch was missing.
1 of 3 people
found this instruction helpful.
-
Don from Eugene, OR
- Really Easy
- Less than 15 mins
Pulled the two wires out from the access hole in the lower part of the refrigerator. Put them in the spade connectors on the new switch, and pushed the switch into place.
Was this helpful?
Thank you for voting!
end cap for door shelf retainer bar had broken
1 of 4 people
found this instruction helpful.
-
Ariane from Mineola, NY
- Easy
- Less than 15 mins
Used a flat screw driver to push in the small metal piece holding the end cap in place(this was to detach the old broken end cap). Then snapped on the new end cap.
Was this helpful?
Thank you for voting!
Bad switch for door prevented interior light from coming on
0 of 1 people
found this instruction helpful.
-
Patricia from Sylva, NC
- A Bit Difficult
- 15 - 30 mins
-
Pliers, Screw drivers
Just as your video described, although due to the age of the fridge, it took a bit longer to remove the defective switch. Your video made this so simple, I can't imagine why we lived with a dark fridge for so long! I was ready to buy a whole new fridge, as repairmen are often nonexistent for small repairs. I am the biggest fan of yo
... Read more
ur company & it's repair video. THANK YOU SO MUCH
Read less
Was this helpful?
Thank you for voting!
light in freezer section not working
6 of 24 people
found this instruction helpful.
-
Victor from Fort Myers, FL
- Easy
- 15 - 30 mins
-
Pliers, Screw drivers
Using plyers Pulled old switch down and out. Put new one in and pushed new switch up into position. The switch plugs into the contacts, no wiring needed. Worked like a charm. You saved me 200 dollars GE repair bill. Thanks
Was this helpful?
Thank you for voting!