T1024ADF LG Washer - Instructions

Replaced valve body, very easy to fix as per the video, runs normal.

After unplugging the washer I cut the water off. I took the water hoses off, then the back top panel using a phillips head screw driver. I then used a pair of pliers to take off the two hoses and clamps. I unplugged the electric connection on each solenoid, took out 5 screws replaced the part and did everything in reverse order. Problem s ... Read more olved. Thanks for the fast service on my order.

I can’t really say it was easy and I just did it

Unplug washer , shut off water supply, remove water supply line, remove drain line from pipe, Unscrew 4 Philip head screws and gently bend panel enough to lift and remove. Beware of sharp edges. The hoses on the pump are hard to remove so remove the three # 10 MM bolts from the pump base and then squeeze the hose clamps and move them bac ... Read more k away from the pump. Use a pair of channel lock pliers and hold the hose while twisting the pump motor this should loosen the hose enough to remove the hose. Do not remove the plug wires on the pump, unplug at the wire harness in the plastic bag on the side of the machine. your new pump should come with a new wire harness already plugged into the pump. Just swap it out with the old one Be careful not to pry the blue connector apart just press down on the little pin in the center of the connector and it just slides out. Note how the wire harness was routed and held in with the supports.
When reinstalling the three bolts do not over tighten. Reattach the hoses and the compression clamps. Reinstall the back panel make sure the instruction label faces out and the vents are on the top. reconnect the drain line to the pipe and reconnect the supply hoses Make sure Hot and old are correct., Plug machine in and run with the towels you used to mop up the water through a wash cycle and check for leaks.

Everthing went to plan except the wet side of the parts removal was difficult. used puller to remove the wash plate and got it to release. But the plastic part of the wash plate released and left the aluminum part still on the coupling. Corrision was the problem, and I had to again use a puller to remove this part of the wash plate. So it ... Read more wasn't a matter of just lifting the wash plate off by hand. The rest of the replacement was fine.

Very close to the installation video online at Parts Select. Removed the back panel, unclipped the hose from the inner fitting and replaced with the rear hose. Why it didn;t leak on the inside is interesting as there was no clip on the at the inner fitting.
The one difference from the existing install video online was that I didn't ... Read more have to tip the washer over ~75 degs before replacing. I instead found that I could put to cinder blocks under the back edge to replace the drain hose. This made the job quicker without having to worry about having a box for it to rest on (with any risk of falling to the floor).

turn off the water, unplug washer from power. remove two screws holding rear top plate. Here's the hard part. Pry the rear top plate from the top of the washer. It has multiple snap in guides across the front edge and they are very tight. Be careful and apply steady pressure straight up and they will eventually come free.
I mark ... Read more ed each of the electrical inputs going to the old valve before removing. Remove the wiring harness. Again be careful and ease them off. the connectors
come apart easily. Remove the hose clamps with pliers and slip off the hoses. They are long enough that I trimmed off the soft ends of the old hoses and still had plenty of hose to reconnect. Remove the filler hoses. Remove the screws holding the valve to the machine. Re install the new valve in reverse order. Goes back in very easily.
Make sure to secure all the hoses. Run a wash cycle with an empty tub to make sure everything is working properly and nothing is leaking. Snap the rear top plate back into position and secure with the two screws Should take less than a couple of hours to do this job. Again the hardest part is getting the rear top plate off.

unplugged machine, turned off water valves. Moved machine away from the wall. Disconnected supply lines. Removed cover housing water valve assembly.
Took a picture with phone. Disconnected water and electrical wires. Removed water valve assembly . Installed new assembly ,cover and reconnected supply lines, plugged power cord in, turn ... Read more ed on water supply valves. Done.

I HAD A CHAT WITH LG EXPLAINED THE PROBLEM . SAID IT WAS THE WATER SHUT OFF VALUE. V EVEN SENT THE PAGE WITH PART# TO ORDER ONLINE.

LOVE LG CHAT!!!

The problem ended up being the pump motor which discharges water from the washer. I figured out this was the problem after trying several things. I determined the motor was fine when it was empty. With the unit turned off, if you can rotate the tube with a quick spin and it lights up, probably this is OK. Then I tried to run it again and ... Read more it went about 1/2 way through the cycle and stopped and started humming again. So I started emptying out the water, which I noticed was about 5 gallons which is way too much. so once empty, I took the pump off by turning unit on side. There are two hoses with hose clamps, and a few screws. Be careful to mark which wire plugs onto which side of the pump. One is brown and one is black. If you take the pump housing off, with the 3 screws, you should be able to pull the motor apart. Mine had water and scum from the wash in it, which was a dead give away that it was the problem.