SWFB73WN Speed Queen Washer - Instructions

ordered and replaced heater element, did not fix the problem so ordered thermal fuse and cycling thermostat when it arrived installed them still did not work. Went to the next item on list thermal cutoff kit ordered it, when it arrived installed and BINGO!!! It works... $107.00 later a dryer that works!!!!!

Replaced the heating element. Everything copacetic.

I watched the video on utube first, and thought this is a breeze. I'm older and so getting down on my but in the back was what I thought was going to be the hardest part. I removed the screws that held the back plate. Once inside the back I removed the plugs to the heating element with plyers, and the little round thing with nut driver ... Read more . Ok, what now the video showed where the element just lifted out, mine didn't it was totally encased in the housing. So I felt around to see what was holding it and found a little screw on the backside of the housing, which took some work, and the head lamp so I could see, finally after all that I got the little screw out. The housing for the element still would not come out. so I went back to the video, no help there because the housing on the video just came out and went together about halfway up the housing, mine didn't it was just one piece, so I came here to parts select site and read what other people had said regarding their dryer. I found the information I needed. Thank goodness. I removed the two screws in the front of the lent trap, opened the top of my dryer removed the little Hex nut that held the housing in place, then I went back and removed the heating housing, replaced the element. It was kinda tight, but it fit. I went back to the front put the hex nut back on replace the two nuts in the lent trap closed the top of my dryer, sat back down and replaced that little round thermostate thingy, plugged in the wires to the heating element replaced the back plugged it in and Oh Yeah I had heat. The experience demanded a "High Five" , I felt like a million bucks- this old lady did it herself and the hardest part was having the correct information and getting up and down off the floor. Thanks for all the help!

Pulled the dryer out, unplugged from wall, removed vent hose and back covers. Poked hole through the label on the dryer frame to remove the heat element case spring retainer. Pulled the element housing out of the dryer and separated the element from the outer housing and did an ohm test. Test showed an open circuit. I found the burnt spot ... Read more in the element and ordered a new one. Reinstalled with new element and everything works great.

Went on-line, used Youtube to diagnosed heater element problem, went online and PartSelect's name came up-- easily found the element I needed -- the price was so reasonable that I did not feel I needed to price repair. Ordered the part -- part came fast-- no hasles.

I replaced the heating coil and the dryer works perfect. Thanks for the quick service in shipping the parts to me.

Everything wears out with age. This is the second element I have replaced on this dryer. The time is fast approaching the dryer too will go the way side. For now, though, we just keep her going as best we can. Simple installation using simple tools. Safety first, unplug the unit. Make comfortable room to work on it from behind. Remove the ... Read more back panel, push the top off and unscrew the retainer. Remove the bottom retainer screw and the two wires on the element itself. All you have to do now is lift the element case off the bottom bracket, remove the old element and replace with the new in reverse order. Viola! Be cautious of your new drying times. It seems a fresh element brings new life to drying your clothes. We have found it has been cut by more than a third time. As a side note; bring the shop vac out to suck away all the lint that accumulates inside. Fire hazard for one, deterant to life of machine also. You don't have to be an electrical genius either. If it comes down to that type of repair....Better call a repairman! =0)

Aser your instructions I ordered and replaced the elemateand now it is back to normal. Much thanks

Remove the screws from back cover to remove it.
Remove the two philips screws of the filter on top of dryer, to open top cover.
Once open, remove the screw that holds the heating element housing.
Unplug the terminals from heating element.
Unscrew the heating element from its housing.
Replace the heating element. ... Read more r />Screw on the opposite way you disarm the dryer.

Read less