SWFB71NN Speed Queen Washer - Instructions

Super easy!
-unplugged
-removed the 6 screws in the rear
-pulled off the back panel
-unplugged the 2 wires attached to the heater element (note which one connects to where)
-remove dryer filter and the 2 top screws that next to it
- lifted the top up
- there is one screw at the top of the heater elemen ... Read more t casing that needed to be removed.
- poped the heater casing away from the dryer.
then pulled it out from the bottom
- removed the one screw holding the heater element in the case, and slide it out
-slide the new one in, and put the screww back in
-pushed the heater casing back up in the dryer and connected the 2 element wires.
-slide the heater casing in the 2 slots and pushed it backing to the dryer at teh top.
-screwed the on screw back in at the top of the casing.
- put the dryer top back in place and 2 fliter screws back in.
- reattached the back panel. and plugged back in.
- viola...

Remove screws at lint filter, open top of dryer. Remove hex screw holding top of element casing. Slide dryer away from wall, remove 5 hex heads from rear panel, exposing element casing. Remove two screws holding sensors, and move aside. Lift dryer casing slightly and pull towards you to disengage from rear panel. Turn over and remove srew ... Read more holding element to casing at bottom. Slide element out, and unplug two wires, noting position of each wire. Reverse procedure to reinstall element. Dryer works better than it has for years !

Fairly straight forward except for hidden 5/16 self tap screw coming from back side of heat ducting that is welded to drier. You have to remove this by feel and restart by feel which may be difficult for some. This screw holds the element to the heat duct. It has to come out

My son did the repair and thought it went very well. You saved me about $400 to $800 in that I didn't have to buy a new one. You got this part to me in 48 hours and I appreciated your timely manner. Your service is great! Thanks MZ

ordered on-line monday recieved on tuesday wife drying clothes tuesday evening--------just took out old element and hooked up new one --- very easy

Replaced heating element,thermal fuse,cycling thermostat,thermal cut off kit and don't forget to flip your dryer fuse in the breaker panel that was a big one for me. Hope this helps you.

I removed the back panel and took the 2 screws out at the lint screen, lifted the top back so I could remove the bracket holding the heating element can. After this was completed I was able to remove the heating element and install the new one, I had to cut the old connectors off and wire nut the new connector together. After this part wa ... Read more s completed I reinstaaled the heating element can, secured the top back down,reinstalled the the back panel and pluged it in and wa-la it worked. I also wanted you to know that your prices are about $ 7.00 less than a few of the other part sites I checked on line and one of the sites even said that the part I needed was no longer available. I am sure glad that I kept looking and found your site because you saved me from buying a new dryer, thank you and if I get asked where to get parts I will recommend PARTSSELECT.COM.
Fred

Located heating element at PartSelect easily.Worked perfectly

Took off the back panel of the dryer. Removed the screw holding the drying element in only to discover it would not fit out the bottom of the case holding it because it was too close to the bottom of the dryer. Had to take off the top of the dryer and remove the casing, remove the element, replace it and put the casing back. Not too diffi ... Read more cult, only two wires and one screw. Did make a couple of rookie mistakes making me backtrack and redo a few things but nothing major.

Pulled the dryer out, unplugged from wall, removed vent hose and back covers. Poked hole through the label on the dryer frame to remove the heat element case spring retainer. Pulled the element housing out of the dryer and separated the element from the outer housing and did an ohm test. Test showed an open circuit. I found the burnt spot ... Read more in the element and ordered a new one. Reinstalled with new element and everything works great.

Following one of your site's more detailed repair suggestions, I began checking the higher percentage likelihood of failures and stepped-through to what my initial suspicion was: The Heating Element (13% ??). I first checked the fuse (rated at 73% probability) (both thermostats were rated very low as possible problems) and immediately w ... Read more ent to the element. The failure was discovered in short order by checking continuity along the coils until a physical break appeared. The most helpful advice I received was from the pointers to remove the two screws attaching the heat vent/filter plenum in order to lift the dryer top and access the anchor screw attaching the top of the heating element box. I was over-joyed to find that the 29-year-old part number I entered, with the replacement number your system displayed, was PRECISELY the physical size and shape of the original heating element when I opened the package !! To borrow a page from the old PGA TV ad: "(You) guys are good." Many thanks !!

it was easy to replace the element

Went on-line, used Youtube to diagnosed heater element problem, went online and PartSelect's name came up-- easily found the element I needed -- the price was so reasonable that I did not feel I needed to price repair. Ordered the part -- part came fast-- no hasles.

checked element leads with voltmeter (set on ohms) - no continuity. - biggest problem is that the can over the element is screwed in from the back - you have to take out the lint filter and unscrew the two screws beneath it then pry open the dryer top - then you can unscrew the one screw holding the clamp on the can. This seems to be a ... Read more feature added just so people would call out for repair - I can't imagine how it would have been quicker or easier to manufacture it this way. The can just pulls out and is hinged from the bottom - you may have to jerk on it after you remove the clamp. (pull from the top). One screw holds the element in. That is it for the replacement. Now the stupid part - check to see if the exhaust vent is clogged. I pulled several cubic feet of lint out and didn't bother to put a mask on and almost choked to death. I recommend you to get a dust mask before cleaning a tube longer than 8 feet.

un plug power, pull out from wall,remove 5 screws and remove back cover. check heater element for curcuit found to be open. check the 2 temperature units on the heater housing, both ok. Remove the 2 flag connectors on the heating element, 2 wires each on temperature switches.remove upper heater case screw and bracker, lift and slide heate ... Read more r housing out of the dryer. Remove 1 screw holding heater element in the housing. compare old and new element, being the same. follow reverse steps and re assemble.