SVD48600PC Jenn-Air Range - Instructions

Checked online to see what F3 readout on stove meant. It meant replace sensor. Ordered part on a Sunday and part delivered Tuesday, Monday being MLK day. Detached bad sensor(2 screws inside oven)had to pull new sensor connector through hole from behind as insulation was too heavy (only removed 4 screws on right rear panel.Clipped wires to ... Read more gether and reattached sensor inside oven. A cakewalk.

I did only tokeout the four tips balves like a screw 1/2 in. And replace the otherones and is it. Less than 5 minutes for all four to replace

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires to remove the old sensor. Went on line to find out where to order it from. Ordered it, It was on back order but was only about 1 week to receive. Reversed the procedure. WA LA. It works great.

easy to put in

Turned the circuit breaker to "off"
Unbolted the unit from its cabinet (4 screws - visible when the oven doors are open - secured the unit in its cabinet)
Slid the unit out of the wall about 2 inches
Removed the control panel.
Unbolted the cooling fan assembly
Unplugged the assembly from the wiring harness
Re ... Read more moved the cooling fan from the oven

Plugged in the new cooling fan
Bolted the new fan in place
Replaced the control panel
Slid the unit back into position
Bolted the unit in place
Turned the circuit breaker back on
Tested

No problems - the hardest part was having to reach to the back of the oven from the front.

unplug the oven and pull it away from the wall. looking at the oven from the back, the spark module is at the bottom on the lower left. there is a two piece sheetmetal cover over the area of the spark module. use a phillips head screwdriver to remove five screws and the covers come off. the spark module is the blue cube with four push ... Read more on wire connectors. all you have to do is hold the new one next to the old one and swap one wire at a time. both were clearly marked with identical numbers and letters. really nothing to it. it took me longer to clean the back of the oven than to replace the module. the old module was eaton part number Y-54052-3. the new one is eaton part number Y-054052-34.

Removed the two screws holding the element in place. I then pulled the element and wiring out until I saw the connecter. I disconnected the two wires and then chose the correct connector from the package, snapped it back into place, put the screws back, turned on the breaker then tested the oven and found that everything was working corre ... Read more ctly.
This is the second time I have ordered from Part Select, the first time was for a front LED panel on the same appliance. With the help finding the part you need and the comments from other customers I have saved a lot of money by repairing these problems myself. Oh, and the best part is the look on my husband's face when he came home and found out the repairs were made by me and not a repairman that he said I should call. He said he would laugh when the first repair by me didn't work but who's laughing now : )

I turned off the burner and allowed it to cool. I then checked the website for the part and also got a new grease filter and grill grate. When the parts came, I plugged in the new grill burner, replaced the grill grates, and dropped the filter in place. Total time was about 8 or 10 minutes--most of which was opening the packages. The ... Read more grill burner is designed so that it can be removed and replaced with a standard 2 burner unit. No tools were needed. I was glad to find the parts for my 17 year old dual-fuel range.

As the video described I just unscrewed the sensor from inside the oven. Although I couldn't pull the wiring harness through the insulation (the wires were gathered in back with a wire tie) just four screws to loosen the back panel for access to the connection. My wife says it seems to be heating perfectly now.

The problem was easy to find since the board had caught fire and you could tell which board was bad. I had to remove the protecting jacket. Then removed two screws. I disconnected and reconnected the wires one at a time so I could tell where they went.
The hardest part was pulling the stove out and cleaning the dust and split ... Read more food.

I removed two retaining screws that keep the hinges from falling off the stove. I lifted the door up and the hinges disengaged from their mounting pins. I put the door on the kitchen counter and removed the screws holding the stainless steel door cover on. The hinges have two small screws at the back of each hinge. I removed those and the ... Read more hinge lifts out. I put a new hinge in and replaced the two small screws. I did the same on the other side. Then I picked up the door and put the hinge mounts through their respective openings on either side of the oven and dropped them into place. I replaced the retaining screws and that was it. Door hinges replaced! It literally took me about 15 minutes and I had never done it before.

I was told by appliance repairman that sensor and electronic panel were out - so ordered both as PartSelect was less expensive (about 1/2) than service call price. Sensor was in stock and arrived in 2 days, panel was special order from factory.
Replaced the sensor. Pressed Control Lock pad for several seconds and oven clock came on ... Read more . Was able to set baking temp, broiler, and convection operation as normal.
Canceled order on panel as Sensor fixed my problem.

replaced broiler element - still would not heat.
Called repairman and the control panel is out and will cost around 200.00 to replace. To replace the element, my son helped as my arms weren't long enough. Removed two screws at back and two screws on front of broiler brace. Pulled out and removed wires and hooked them to the new el ... Read more ement. Had to turn off circuit breaker. Pushed element back into the holes and replaced screws.
In this instance, it would have been cheaper had I just called the repairman first. However, I have an extra broiler element in case it goes out again.

After reading three other reviews I decided to replace the hinges to save $ (REPAIR SERVICE ESTIMATE WAS $200 +). As another reviewer stated " I spent more time removing and cleaning the glass viewing doors than replacing the hinges". One critical part of the hinge replacement is the removal of the heavy oven door. TO AVOID INJURY DURING ... Read more DOOR REMOVAL IT IS IMPORTANT TO INSERT A "PIN, SMALL NAIL, HEAVY PAPER CLIP" INTO THE SMALL HOLE ON THE ARMS OF THE HINGES. If you fully open the door you will see a small hole on one part of each hinge arm. As the door closes the arm with this hole slips between the other hinge parts. Inserting a pin will prevent the hinge from snapping shut when you remove the door and potentially smashing your finger with its strong spring. Once inserted you can remove the cover plate for the hinge pocket (one screw each side). Close the door to "broiling position" (about two/three inches open) and lift the door up off the bars within the hinge pockets to remove from stove. (Our SS range doesn't have sides so you could see how the door hinges just slip over and lock onto the pins in the hinge pockets.......the pocket trim covers lock the hinges on the pins during normal operation. At this point you just need to remove a few screws to remove the SS door skin to expose the hinges. Remove the one or two screws at the end on the hinge and lift that end up to slide the other end out of the retaining slots. Installation is the reverse...the replacement hinges have cute little pins that hold them open so, after installing on oven door, you can insert them into the hinge pockets and onto the pins as you hold door in the "broil position". After reinstalling the hinge pocket cover plates, you can open the door and easily remove the retaining pins. Sounds like a lot but probably would take approximately one hour if you don't remove glass for cleaning.

I simply looked at the new switch , to see how it fastened in the stove. It had plastic clips that were easily depressed to allow the swithch to be removed. I removed it , (after turning the circuit breaker off to the stove) removed the three wires , and replace them on the new switch and simply pushed it in the space. It snapped in place ... Read more , and the job was done . Works great!