SU130 Jenn-Air Range - Instructions

1. Diagnosed problem = switch at fault not element
Made a diagram of wire positions on faulty switch
2. Ordered part = remarkable service! Switch arrived in less than 24 hours
3.Installed new switch
4. Tested appliance = success!
5. Saved $150 and a lot of aggravation
Terrific site. Excellent help in figu ... Read more ring out and solving the problem. Two thumbs up!

Well I was just guessing the controll switch was bad so I ordered a new one. So I cut off the power and held the switch close to the old one and changed the wires one at a time matching the connection terminals and cut the power back on and presto it WORKED..The service man wanted to charge me 65.00 dollars just to check it out. I ... Read more figure I saved about 100.00 dollers plus I learned something.

Very simple---shut off the power, removed six screws, detached five wires, replaced control switch, put everything back together, turned on power and made husband happy!!!

Followed instructions, once saw and how to replace and replug wires as the instructions it was easy as per your instructions

Really easy ...followed advice posted from others with same problem. Before anything disconnect the power at the breakers and use a voltage detector to verify there is NO POWER!!!! Only need to remove the two phillips screws on the four controller panel, Slide panel away from you to access the controllers. Match wire/connector for connec ... Read more tor from the old to new controller. Reassemble, restore power .. Happy wife!!!. She has been on my case to fix this thing for several years.

I removed two screws that held the switch plate together. Then I removed two screws that held the faulty switch to the swtich plate. I then unpluged one wire at a time from the old switch and pluged it into the new switch. Reattached the switch to the switch plate and then reattached the switch plate to the stovetop. Bingo! Everything wor ... Read more ked beautifully. It was so easy and I saved ~ $100.00 by doing it myself, as opposed to a quote that I got from a local repairman.

AFTER turning off the power supply to the range/cooktop, remove 2 screws holding element in place then remove two slip electrical connectors, and remove element. Reverse procedure for installation of replacement.

1. Turn off power at breaker. Take no chances. Turn on each working burner, fan, oven light to be sure there is no power to the appliance. Then, turn them off.
2. Pull knob on switch straight out to remove.
3. Remove 4 Phillips head screws under control panel. Pull panel gently down, then out toward you slightly to release t ... Read more op edge. Rest control panel on self-clean lock knob.
4. Confirm terminals on new switch match up with old switch.
5. Use needle-nose pliers to gently remove wires from old switch one at a time and place them on the
corresponding terminal on new the switch.
6. Reverse steps 3, 2 and 1. Test switch and burner.

The element is held in by two screws located at the rear of the oven. After killing the power, I unscrewed the two screws (one was stripped so I used a pliers to remove it) and replaced them with 2 new screws. Total time was about 20 minutes. Easy fix!

Removed the element and did a continuity check, the element was bad. The stove is over 25 yrs. old. Went to a local shop who usually are very good in situations like this. They could not find the part. Went on line to Part Select, found the part and verified with a phone call. Ordered and received the part the next morning and fixed the ... Read more stove.

First I removed 7 screws, using a Philips head screwdriver, to allow access to the inside of the oven door. I then removed several more screws to separate the panel holding the seal so that I could remove it and replace it with the new seal. Once the seal was in place I re-inserted all the screws to the panel and door to complete the re ... Read more pair. The knobs just slipped on to replace the ones that broke and fell off.

Removed old element by removing screws from plate and removing old wires. Had to get conversion from electric store as new element was screw in and the old one was hard wired. Stripped old wires and placed on converters. Screwed the electric converter parts to the element. Screwed into oven wall.

I removed 2 screws to release the plate that held four the switces. I removed 2 screws to release the bad switch. I removed one wire at a time and connected the to the same post on the new switch, screwed the switch into place and reinsalled the mounting plate. The stove works fine.

Removed top and front panel

It was worth the money for that little screw, since I didn't have to run all over trying to find the right one.